Download
Share
Print this page
  1. Manuals
  2. Brands
  3. SCALE-PARKFLYER Manuals
  4. Toy
  5. Beriev Be200
  6. Construction manual

SCALE-PARKFLYER Beriev Be200 Construction Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Scale-parkflyer.de
Beriev
Be200
Construction manual
Part 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Beriev Be200 and is the answer not in the manual?

Questions and answers

Related Manuals for SCALE-PARKFLYER Beriev Be200

Summary of Contents for SCALE-PARKFLYER Beriev Be200

  • Page 1 Scale-parkflyer.de Beriev Be200 Construction manual Part 1...
  • Page 2 Beriev Be 200 Beriev Be 200 Beriev Be 200 Beriev Be 200 by Scale-Parkflyer.de Material List Part No. Title piece Material Rumpf: each 2 R1 / R2 Frame side front / back 6 mm Depron each 1 R3 / R4...
  • Page 3 Border reinforcement 6 mm Depron Overlay for Wing 6 mm Depron Overlay for Wing Wood 0,8 mm wood Landing Gear box low 6 mm Depron Landing Gear box side 6 mm Depron Landing Gear box back 6 mm Depron Landing Gear box front 6 mm Depron Border reinforcement 6 mm Depron...
  • Page 4 Nose strip outside 6 mm Depron Wingtip 6 mm Depron 6 mm Depron each 2 R2 - R7 Ribs 6 mm Depron each 2 R8 / R9 Ribs 3 mm Depron each 2 6 mm Depron R10a Reforcement for Rib 1,5 mm Depron each 2 R11 / R12...
  • Page 5 Construction manual, Part 1 1. Frame R5 and R6 stick together. 2. Check for a perfect fit all Rib / Frame parts. ( without any glue )
  • Page 6 3. Put together Frames S2-S9 and S14-S19. 4. Put together wood Parts each on the wing side on the FrameR10 and R13 S10b and S13b. S10 until S13 Frame put together in Hull.
  • Page 7 5. Side Frame R1 and R2 put in the Hull without twist..
  • Page 8 6. For a perfect Hull without any twists, please take a Heeling in wood or see here in 6 mm Depron ( its easy ) You can fix all bars with two-sides tapes.
  • Page 9 8. The Spacer have got follows lenght: Rear Part: 120,5 mm, in the Front: 88,5...
  • Page 12 9. Half-Frames S10c and S13c put in.. 10. S 12a/b parts put together for one Part.
  • Page 13 11. Frame S1 put in the front of the Hull.
  • Page 14 12. Planking the Hull: The Hull please cover with 3 mm Depron. For a perfect finish, please follow next steps: Please flex the Depron Material in the right direction before. Its going easy with a commercial Hairdryer ( min. 1000 Watt ). Take only one Segment from Frame to Frame.
  • Page 15 A bent Segment...
  • Page 19 13. Please take a cut between R13 and R13b for pine wood R17/R18 ( 10x2x262 mm ).
  • Page 20 14. Please cut out space for pine wood.
  • Page 22 15. 6X6 Depron R8 for a better hold...
  • Page 23 16. Planking for the side, ready to fix.
  • Page 27 18. Ready to turn the Hull on the Top.
  • Page 28 19. And now you need follow spacer to hold on: Front 120,5 mm und aft part 88 mm. Please wait for planking on this lower side on four segments to turn again in the normal position. ( front, middle and aft part ) Here you see a Picture from the finished hull, You see the part No.R30 like a surf Step.
  • Page 30 Scale-parkflyer.de Beriev Be200 Constuction Manual Part 2...
  • Page 34 20. Turn back the Hull in first position. 21. Tail Montage:...
  • Page 36 23. Please cut both Hull Frames ( up and low ) to fit the Tail. Check before the perfect geometric position.
  • Page 37 Behind them, please put in again the cut Part from the Hull Frames. Put inside the Servo for Rudder and Check function before a montage. Here you see a water protect cover. 24. Elevator Montage:...
  • Page 38 You need a 160 mm Carbon pipe ( diameter 5 mm ). Outside is a Aluminium 6 mm Pipe ( inside 5 mm ) to fix the Elevator. The Middle Part is fix in the Tail. Outside Pipes are fix in the Elevators. Alu: 2 X 60 mm, one Part 15 mm. 25.
  • Page 40 26. To move the Elevator, take a 4 mm Carbon or Aluminium Pipes ( Inside 3 mm ) in the Elevator. A 3 mm Full material Carbon Pipe in the Rudder bar move the Elevator. 27. Servo Rudder bar please construct it see template by all Kits and blueprint.
  • Page 42 28. For a better fixing, please take outside a roof mate with glas fiber. 29. Servo for Elevator please pu in the hull and test the Roof bar for a perfect way in all positions.
  • Page 43 Servo neutral position Servo in Pull position...
  • Page 44 Servo in pull position...
  • Page 45 Servo in push position...
  • Page 46 Now you can close the second Tail Cover. 30.Beginning the construction of the Wing: Put on T1, Wing ground Main Support T2 / T3.
  • Page 47 31. Please cut Ribs in the position of the Main Support.
  • Page 50 32. By Rib R10 put on reforcement R10a. For Aileron flaps, take T7/T8 on the position.
  • Page 51 33. Both Wing Parts take it together. Fix the Main Support with Glas fiber. The same case by Rib R10.
  • Page 54 34. Second Support with wood take into construction. Before, please cut the Ribs out.
  • Page 57 35. To fix the Wing later on the Hull, take two Aluminium Pipes ( 7 mm outside, 6 mm inside for 6 mm Plastik screws ) in the Wing ground. Fix it with fiber glas and roof. Please see on picture, on the up side of the Pipe, it is 3 mm higher than the Support ( for Wing Cover )
  • Page 58 36. Overlay for Wing R9 and Reforcement R10 put together.
  • Page 59 37. Take any wood ( 1,5 mm ) to fix the Plastik Screws on the lower side of R9/10. For the correct geometric position, please take this part with the Wing on the Hull and check the correct hole see Aluminium pipes in the Wing.
  • Page 60 38. Put in the Servo for both Elevators.
  • Page 63 39. Prepare the Wing Cover T28:...
  • Page 66 40. cut all material over wing part. 41. Nosestrip T8 / T9 put on.
  • Page 68 42. A perfect shape is urgent for good flight conditions. The middle of the Nose you see in this scheme. Measurement by R1 ist 10 mm, by R7 6 mm and R11: 4 Nose strip lease grind in correct shape.
  • Page 69 43. Overlay R9/R10 screw on Wing. Both together on the Hull to fix the correct position. Then you can fix R9/R10 on the Hull. The wood part in the front. 44. Now you can cut the Depron see here from the Hull.
  • Page 70 45.Landing Gear box please prepare see picture. Parts ( R11-R15 ). Put it under the lower side of the Wing Overlay.
  • Page 72 46. Take R16 with R17 together. ( Wood on the up side ). Take a small cut intoDepron, by the position for pine wood R18.
  • Page 75 47. Lower side, put on R20 / and R21.
  • Page 76 48. WoodCover R22 take it in the Corner of Wing Overlay.
  • Page 77 49. Wing mount it again on the Hull. Parts T24 / T25 on the Hull, and with the Cover T27 close it.
  • Page 78 Scale-parkflyer.de Beriev Be200 Construction Manual Part 3...
  • Page 80 50. R23 / R24...
  • Page 81 51. Cover R25 52. Cover ( Wing side ) T22...
  • Page 82 53. R26 in a round shape with R25 and put on R27. Take Parts by Cover R25. The same system for part R28.
  • Page 84 54. Hull nose please grind like template by Kit or blue print.
  • Page 85 55. L14 between Hull and Tail.
  • Page 86 Situation Now.
  • Page 87 56. Turbine Pipe R29 please turn around to a Pipe.
  • Page 88 57. The Template R31 show you the correct shape. Pull over the Template over R31 and put it together with Epoxy. You can put in the EDf Fan for a correct shape. 58. Same situation with R30 in 6mm.
  • Page 89 59. Take EDF Fan out, Tamplate R32 inside and stick together.
  • Page 90 Fix by Tape...
  • Page 91 60. EDF Fan stick in, cable goes outside. 61Grind the Fan see scheme.
  • Page 92 61. Turbine outlet R33 turn it to an cone and stick in the aft part.
  • Page 94 62. One of the Engine Support R34 take it together with reinforcement R35. Two of R34 take ist together too. Take it in a angle of 90° degrees of the Hull. Please take a reinforment like glas fiber and roof mate for a better hold. Next step, you can stick on the side the two R34 parts.
  • Page 96 Ist your opinion to found the position for Controllers. In this picture, the Controller are in the Parts R34. I have put my Controller in the Hull to save for any Water. Urgend: Please cut one of the red cable for BEC. Your Receiver need only one signal.
  • Page 99 63. cable goes in the Hull, see Pictures. 64. When you are finish, close the Gear Box with Part R19.
  • Page 100 65. Flap Casing T13 until T16 preparing: You need a 9 mm Casing, so we use a 6 and a 3 mm Depron Part. Please stick by all 6 mm Depron Parts a 3 mm Part off. Grind the reday part into a aerodynamic shape and stick in the lower side of the Wing ground.
  • Page 102 Position of all Flap Casing parts.
  • Page 104 66. Prepare all Floaters: stick on all parts T19-T21 together, see pictures.
  • Page 105 67. In the middle take wood part T17.
  • Page 106 68. grind the floaters.
  • Page 109 69. Stick on position R10, see attached Picture. Take fiber-glass with roof to fix.
  • Page 111 70. For all Servos, you can built a Box with pipes to protect all Servos. Please spray all Servos with Wet protect too. Rudder: Elevator:...
  • Page 112 71. fixing aileron with smallscrews. ( 2 mm Hole in Alu and Carbon Pipe )
  • Page 113 72. The Center of Cravity is 84 mm before aft Border see Scheme.
  • Page 114 73. Lipo Position is in the front of the opening place in the Hull. Recommendation for kapazity is 3 S 3500 – 5000 mAh.
  • Page 116 74. Both Controller please take 40A or more. 75. a small Rubbertape ( 1 mm ) please stick on one of the Overlay. 76. Finish: To found the corrct position fort he Window, take both templates from the blueprint to fix it on the Hull, see picture.
  • Page 118 77. For Finish take only colours without solvent glues.
  • Page 119 78. RC Controll: Servo way: - Elevation: complete way you see in Depron Tail - Rudder: 15 mm both side. - Aileron: 12 mm both side. For the best Control on the Water, mix a engine differentiaton in your RC Transmitter.
  • Page 120 - Center of Gravity ok? Any Questions for build or Flight? Please contact me by any questions. Im happy to see some pictures from your Modell by Email. Have a pleasure time with your new Waterplane. Frank Seuffert info@scale-parkflyer.de www.scale-parkflyer.de...
  • Page 121 Warning!! Before you fl y the R/C model it is essential to read the operating and building instructions in full. This sheet is part of the operating instructions. Please keep it in a safe place for further reference. If you ever sell the model make sure to pass on this sheet to the new owner together with the model. A remote controlled model aircraft (model plane ) is not a toy.