Cleaning; Safety Inspection; Disposal - ebm-papst G1G126-AB13-53 Operating Instructions Manual

G1G126-AB13-53
Motor/electronics Deficient cooling
overtemperature
Ambient temperature
too high
Impermissible point of
operation
Deflagration Leakage of the air/
gas mixture being
conveyed
In the event of further malfunctions, contact ebm-papst.

5.1 Cleaning

To ensure a long service life, check the fans regularly for proper
operation and soiling. The frequency of checking is to be adapted
accordingly depending on the degree of soiling.
; Dirt deposits on the motor housing can cause overheating of the motor.
; Soiling of the impeller can cause vibration that will shorten the service
life of the fan.
; Severe vibration can destroy the fan.
; In such cases, switch off the fan immediately and clean it.
; The preferred method of cleaning is dry cleaning, e.g. using
compressed air.
; If water is required for cleaning, the preferred method is to perform
cleaning with a conventional water hose or to employ foam cleaning.
; Do not use aggressive cleaning agents!
NOTE
The device does not need to be cleaned.
; If cleaning agents have been used, rinse these off with clean water.
; If severe corrosion is visible on load-bearing or rotating parts, switch
off the device immediately and replace it.
; Repair of load-bearing or rotating parts is not permitted.
; Operate the fan for 2 hours at maximum speed to permit the
evaporation of any water that has ingressed.
; If cleaning does not eliminate vibrations, the fan may need to be
rebalanced. To have it rebalanced, contact ebm-papst.
; The fan is equipped with maintenance-free ball bearings. The lifetime
lubrication of the ball bearings is designed for a service life of 40,000
hours.
; If bearing replacement is necessary after that period, contact ebm-
papst.
; Adapt the maintenance intervals to the level of dust exposure.
Item no. 53368-5-9970 · ENU · Change 202174 · Approved 2018-12-27 · Page 9 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Improve cooling. Let

5.2 Safety inspection

the device cool down.
What to check
To reset the error
Contact
message, switch off
protection
the line voltage for at
cover for
least 25 s and then
intactness or
switch it on again.
damage
Reduce the ambient
Device for
temperature.
damage to
Reset by reducing
blades and
control input to 0.
housing
Correct the operating
Fastening the
point. Let the device
cables
cool down.
Insulation of
Check for leaks;
cables for
replace blower if not
damage
properly sealed
Abnormal
bearing noise

5.3 Disposal

For ebm-papst, environmental protection and resource preservation are
top priority corporate goals.
ebm-papst operates an environmental management system which is
certified in accordance with ISO 14001 and rigorously implemented
around the world on the basis of German standards.
Right from the development stage, ecological design, technical safety
and health protection are fixed criteria.
The following section contains recommendations for ecological disposal
of the product and its components.
5.3.1 Country-specific legal requirements
5.3.2 Disassembly
Disassembly of the product must be performed or supervised by
qualified personnel with the appropriate technical knowledge.
The product is to be disassembled into suitable components for disposal
employing standard procedures for motors.
5.3.3 Component disposal
The products are mostly made of steel, copper, aluminum and plastic.
Metallic materials are generally considered to be fully recyclable.
Separate the components for recycling into the following categories:
●
●
●
How to check How often
Visual inspection At least every
6 months
Visual inspection At least every
6 months
Visual inspection At least every
6 months
Visual inspection At least every
6 months
acoustic At least every
6 months
NOTE
Country-specific legal requirements
Always observe the applicable country-specific legal
regulations with regard to the disposal of products or waste
occurring in the various phases of the life cycle. The
corresponding disposal standards are also to be heeded.
WARNING
Heavy parts of the product may drop off. Some of the
product components are heavy. These components
could drop off during disassembly.
This can result in fatal or serious injury and material damage.
→ Secure components before unfastening to stop them falling.
Steel and iron
Aluminum
Non-ferrous metal, e.g. motor windings
What action?
Repair or
replacement of
device
Replacement of
device
Fasten
Replace cables
Replace device