BN Thermic HCA2 Series Instructions Manual

BN Thermic HCA2 Series Instructions Manual

Advertisement

Quick Links

Thank you for purchasing a BN Thermic product. Manufactured to a high standard, this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance. Please ensure instructions remain with your customer for their reference.
REGISTER: PLEASE REGISTER THIS PRODUCT ONLINE TO ACTIVATE YOUR GUARANTEE AT
PLEASE READ THESE INSTRUCTIONS, NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS,
AND CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
Important Note. For an HCA2 air curtain to provide an effective air barrier, a high air velocity is required. The resulting noise output
must be considered. For this reason, we do not recommend HCA air curtains for smaller shops or where people are working in
close proximity to the entrance.
1. SAF E T Y IN ST RU CT IO N S

1.1 ELECTRICAL SAFETY

WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. If in any doubt consult a qualified electrician.
You must also read and understand the following instructions concerning electrical safety.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and the
safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
Installation should always be carried out by a qualified electrician or a competent person in accordance with current electrical regulation.
Ensure that the insulation of all the cables on the appliance is undamaged and safe, before connecting it to the power supply.
Ensure that the cables are always protected against short circuit and overload.
Regularly inspect the power supply cables for wear or damage and check all connections to ensure that none are loose.
Important: Ensure that the voltage marked on the appliance matches the power supply to be used.
DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified electrician.
The unit should be protected by a suitably rated isolator and MCB.
This air curtain is IP20 rated and is suitable for indoor or under cover use only.
This air curtain must be hard wired in position.

1.2 GENERAL SAFETY INSTRUCTIONS

✓ Remove all packaging and store it away from children, check the package and air curtain for visible damage or tampering.
✓ Familiarise yourself with the applications and limitations of the air curtain.
✓ Ensure the air curtain is in good order and condition both physically and electrically before use. If in any doubt, do not use the unit and contact
your supplier.
✓ Only use recommended attachments and parts. To use unauthorised parts may be dangerous and will invalidate your warranty.
✓ Keep tools and other items away from the air curtain when it is in use.
✓ Keep children and unauthorised persons away from the air curtain, as it gets hot.
✓ Disconnect from mains and allow to cool before attempting any cleaning or maintenance.
X
DO NOT use in areas where hazardous gasses or dusts may be present.
X
DO NOT locate the air curtain directly below the power outlet.
X
DO NOT disassemble the air curtain for any reason. This air curtain must be checked by qualified personnel only.
X
DO NOT use this air curtain to perform a task for which it has not been designed.
❑ WARNING! This air curtain is not equipped with a built-in device to control the room temperature. Do not use this air curtain in a small room
if it is occupied by people not capable of leaving the room on their own, unless constant supervision is provided.
❑ WARNING! Ensure you observe the safety distances and mounting heights and there is no possibility of inflammable materials coming into
contact.
www.
.co.uk
bnthermic
INSTRUCTIONS FOR:-
AIR CURTAIN
Model:- HCA2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HCA2 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for BN Thermic HCA2 Series

  • Page 1 Model:- HCA2 Thank you for purchasing a BN Thermic product. Manufactured to a high standard, this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. Please ensure instructions remain with your customer for their reference.
  • Page 2 3. D E S CR IP TIO N BN Thermic HCA2 air curtains consist of a casing, motor, tangential fan(s), electric heating elements and electronic controller that facilitates the use of a SystemX controller and the ability to easily daisy chain up to another 11 air curtains. Each air curtain is supplied with a wall mounting bracket as standard.
  • Page 3 WALL MOUNTING All models come complete with a wall bracket for vertical wall mounting. Model Dimension A HCA2-09 787mm HCA2-13 1295mm HCA2-18 1795mm Ensure that the wall will take the total weight of the air curtain. Securely attach the wall mounting plate to the wall using suitable fixings (not supplied) to take the weight of the air curtain.
  • Page 4 CEILING MOUNTING ON DROP RODS There are 4 x M6 Threaded holes in the top of the air curtain to attach M6 drop rods. Ensure the ceiling will take the total weight of the air curtain and leave a minimum of 110mm between the top of the air curtain and the ceiling for access. See drawings below showing the spacing and positioning of the drop rods.
  • Page 5 5. R EM O V IN G F RO NT CO V E R Remove the screws along the air grille. Gently remove the guard by moving the bottom towards you and lifting it off the fixing tabs on the top. Fitting is the opposite of removing making sure you locate the cover on the top tabs first.
  • Page 7 7. CO NT RO LL E R S You may connect this air curtain to any one of our range of SystemX controllers using a network cable. We recommend you use our network cables as they have been thoroughly tested and are totally compatible. Problems arising from using non-standard or inferior network cables are not covered by the guarantee.
  • Page 8 IMPORTANT: No liability is accepted for incorrect use of this product. BN Thermic Ltd, WARRANTY: Your BN Thermic product is guaranteed for one year from date of purchase. We will repair 34 Stephenson Way, or replace at our discretion any part found to be defective. Our warranty does not cover corrosion. We Crawley, RH10 1TN cannot assume any consequential liability.

This manual is also suitable for:

Hca2-09Hca2-13Hca2-18

Table of Contents