Daktronics OMNISPORT 2000 Quick Reference

OMNISPORT
1. Confirm that the timer is reset.
Before
2. Set the timer to the correct event and heat. The right LCD,
Race line 2 displays E:(event) H:(heat) R:(round) L:(total lengths).
3. Verify the correct number of lengths for the current event and
heat.
1. Timer Starts.
2. Turn off any unused lanes.
3. Watch the lengths complete counter and lane status for each
individual lane.
During

With touchpads at the near end only, the timer will show the
Race
lane status on line 1 of the left two LCDs and line 2 will show
the lengths completed for that lane.

With touchpads at both ends, press [] and [] to scroll forward
or backward through these three views:
Page 1 Near end status on line 1 and far-end status on line 2.
Page 2 Near end status on line 1 with lengths complete on line 2.
Page 3 Lengths complete on line 1 with far-end status on line 2.
1. Confirm that all lanes with an athlete have finished.
2. DQ any disqualified athletes.
After 3. Print out the results with backup times.
Race
4. Edit the race results (for advanced operators only).
5. If any of the results were modified, print out the results again.
6. Reset the timer and get ready for the next event.
Lane Status Indicators:
(Blank) Lane is Off.
- Timer is Reset.
99-1
Arming delay. When there are numbers
(counting counting down, the timer will ignore any
down) touchpad presses.
+
Lane is armed for split time.
*
Lane is armed for finish (last length).
o
Race is over for this lane.
?
There is a problem with the lane module.
Special Timer Operations
Always Ready Start
 If a start was missed because the timer was not reset, or if the
timer was reset following a valid start you can still recover the
race. It is important that this is completed before the timer
receives the first touches.
Setting the arming delay
 The arming delay is the amount of time after a start or split that
the timer will ignore touchpad presses. This is primarily used in
relays to allow a finished athlete time to exit the pool without
adding a touch to the timer. The arming delay for each
touchpad is displayed on the LCDs under the appropriate lane
number.
Test screen for the lane modules.
Entering Home, Guest 1, Guest 2, and Guest 3 scores.
Printing an Event Order.
Printer Paper Specifications
ED13584
Rev 8 19 August 2013
Page 1 of 8
®
2000 SWIMMING QUICK REFERENCE
201 Daktronics Drive PO Box 5128, Brookings, SD 57006-5128
Tel: 1-800-DAKTRONICS (1-800-325-8766) Fax: 605-697-4700
Web: www.daktronics.com/support
Look at the right LCD, line 1. If the running time is not
00:00.0, press [ ]>[
RESET
Press [ / ] and type in the correct event and heat
EVENT HEAT
numbers. If using a programmed event order, press [
], [ +1] or [
EVENT HEAT HEAT
Look on the right LCD, line 2. If not correct, press
[ ] and type in the correct number.
LENGTHS
Typically started automatically from the horn start.
(Optional: [ ] for manual start).
START
Press [ / ] to turn the desired lanes off. Press
LANE ON OFF
again to turn on.
If a lane has an extra touch and the arming delay is
counting for that lane, press [
removes the last touch and arm the lane for the next split.

If a lane has an extra touch:
press [- ]>[(1-10)]>[
TOUCH

If a lane is missing a touch:
press [+ ]>[(1-10)]>[
TOUCH
If the finish of the race is about to happen and the lane
status is not "*", either press [
appropriate lane(s), or [
FINISH ARM ALL
Look at the left two LCDs to verify that the final touch has
been received.
Press [ ], [(1-10)] and [
DQ
Press [ / ] and review the printout.
STORE PRINT
Press [ ] to get into this function. See the OmniSport
EDIT
2000 operator's manual for complete instructions.
Press [ / ].
STORE PRINT
Press [ ]>[ ]. The scoreboard will continue to
RESET ENTER
display the results of the last race until the start of
the next race.
Printout Time Label Descriptions
+
Plus touch
-
Minus touch
B (1-3)
Buttons 1 through 3
R
Relay take-off platform trigger
*
Discrepancy between touchpad and backup
B or BK
Backup time
E
Edited time
M
Manual time
F
Early relay exchange
R (1-3)
Relay exchange 1 through 3
Action
After the timer has been reset, press [
you for the time of day that the start was received. The time
displayed on the LCD will be the time of day from the last start
received. If this is not the desired start time, you will find all of
the start times received printed on the log printout. Type in the
correct start time of day and press [
Press [ ]>[4]>[2]>[5] and then use the numeric keypad to
MENU
enter an arming delay of 0-99 seconds followed by [
return to the main swimming screen, press [
Press [ ]>[5> [2] to show the lane module test screen. To
MENU
return to the main swimming screen press [
Press [ ]>[2]>[1] and then enter in the team scores using
MENU
the numeric keypad followed by [
swimming screen, press [
MENU
Press [ ]>[3]>[2], [ ]. To return to the main swimming
MENU ENTER
screen, press [ ].
MENU
The OmniSport 2000 uses standard thermal calculator rolls of
1
paper. They are 2- / " x 155'. Some rolls are 165' long; just tear
4
off 10' of paper before inserting the roll into the printer.
].
ENTER
NEXT
–1]
(1-10)]. This
SPLIT ARM
]
ENTER
]
ENTER
(1-10)] for the
FINISH ARM
]>[ ].
ENTER
] for each appropriate lane.
ENTER
]. The timer prompts
EDIT
].
ENTER
]. To
ENTER
].
MENU
].
MENU
]. To return to the main
ENTER
].