Advertisement
Quick Links
Operation Manual
Core Drill
61500
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61500
Summary of Contents for WilTec 61500
- Page 1 Operation Manual Core Drill 61500 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Base screw Base 10 Water collecting hood (optional) 11 Spindle 12 Water ring sembly 13 Gear box 14 Shift knob 15 Centre cover 16 Stator shell © by WilTec Wildanger Technik GmbH Item 61500 Page 3 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 4 Voltage: Please note that the power voltage should not be more than ± 5 % of the rated voltage. Higher voltages however can cause irreparable damages. © by WilTec Wildanger Technik GmbH Item 61500 Page 4 http://www.WilTec.de http://www.aoyue.eu...
- Page 5 Rotate the spindle back and forth (easy to shift) at the same time until the shift is in place. Do not shift when the machine is full-speed operated, overloaded or stuck. © by WilTec Wildanger Technik GmbH Item 61500 Page 5 http://www.WilTec.de http://www.aoyue.eu...
- Page 6 Attention: The manufacturer does not assume any responsibility for caused accidents due to the machine not being solid or fixed safety facilities are not in appropriate place. © by WilTec Wildanger Technik GmbH Item 61500 Page 6 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 7 After you have used the machine for about 300 hours, you should check the wear of the carbon brushes and replace them if necessary. Like any other work on the engine this must only be done by an authorized technician. © by WilTec Wildanger Technik GmbH Item 61500 Page 7 http://www.WilTec.de...
-
Page 8: Troubleshooting
Enhance water pressure, pull out the drill bit, of the hole clean the hole. Water cover Seal of the frame worn out Change the seal. leaking © by WilTec Wildanger Technik GmbH Item 61500 Page 8 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de... - Page 9 Power cord Ring Cross level screw M4×20 Class II tooth shaft Cross level screw M4×10 Rolling pin pad Switch box Flat rolling needle (40) Switch D18 Bearing © by WilTec Wildanger Technik GmbH Item 61500 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 10 © by WilTec Wildanger Technik GmbH Item 61500 Page 10 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 11 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.