Radial Engineering PROMS2 User Manual

FEATURES
1. -30dB PAD: Allows balanced +4dB
line-level sources to connect to the
ProMS2 input.
2. Mic input: Used to connect a low
1
impedance, balanced, microphone or
direct box.
3. Direct-1 thru: A parallel direct
output used to bridge the mic or DI to
the primary mixing console.
4. Bookend design: 14 gauge steel
outer shell creates protective zone
around connectors and switches.
5. Full-bottom no-slip pad: This
provides electrical isolation and
plenty of 'stay-put' friction to keep the
ProMS2 in one place.
6
6. Direct-2 output: Equipped with
ground lift. Used to bridge the signal
to an additional audio device.
7. Lift (Direct-2): Disconnects
pin-1 (ground) on the direct-2 XLR
output to help reduce hum and buzz
caused by ground loops.
8. Isolated output: Transformer-
isolated to eliminate ground loop hum
and buzz. Used to bridge the balanced
mic signal to a second audio system.
9. Lift (Isolated output): Disconnects
pin-1 (ground) on the isolated XLR 10
output to help further reduce hum and
buzz caused by ground loops.
1 0 . S t e e l I - b e a m : E n c l o s u r e
eliminates stress that could torque
the PC board.
11. Military-grade PCB: Double-
sided PCB with plated through-holes
is bolted to welded steel standoffs.
12. Eclipse: High performance mic
bridging transformer offers outstanding
a u d i o p e r f o r m a n c e . F e a t u r e s
mu-metal shield for protection against
stray electromagnetic fi elds.
Radial Engineering Ltd. ProMS2
®
2 3 4 5
ProMS2 SPECIFICATIONS
Audio circuit type:
Number of channels:
Frequency response:
Dynamic range:
Maximum input:
Harmonic distortion:
Phase deviation:
CMRR:
Input impedance:
Output impedance:
XLR output:
7 8 9
Ground lift:
RADIAL ENGINEERING 3 YEAR TRANSFERABLE LIMITED WARRANTY
RADIAL ENGINEERING LTD. ("Radial") warrants this product to be free from defects in material and
workmanship and will remedy any such defects free of charge according to the terms of this warranty.
Radial will repair or replace (at its option) any defective component(s) of this product (excluding fi nish and
wear and tear on components under normal use) for a period of three (3) years from the original date of
11 12 purchase. In the event that a particular product is no longer available, Radial reserves the right to replace
the product with a similar product of equal or greater value. In the unlikely event that a defect is uncovered,
please call 604-942-1001 or email service@radialeng.com to obtain an RA number (Return Authorization
number) before the 3 year warranty period expires. The product must be returned prepaid in the original
shipping container (or equivalent) to Radial or to an authorized Radial repair center and you must assume
the risk of loss or damage. A copy of the original invoice showing date of purchase and the dealer name
must accompany any request for work to be performed under this limited and transferable warranty. This
warranty shall not apply if the product has been damaged due to abuse, misuse, misapplication, accident
or as a result of service or modifi cation by any other than an authorized Radial repair center.
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND
DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE OF
THREE YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS WAR-
RANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH
MAY VARY DEPENDING ON WHERE YOU LIVE AND WHERE THE PRODUCT WAS PURCHASED.
®
Microphone Splitter Radial Engineering Ltd.
True to the Music
Passive mic splitter, transformer based
Three-way splitter (one in/three out)
20Hz ~ 20KHz
140dB
+25dBu @ 1kHz
0.005% @ 1kHz
1° @ 100Hz; 4° @ 20Hz
114dB @ 60Hz
150 Ohms, balanced
150 Ohms, balanced
AES standard pin-1 Ground, pin-2 (+), pin-3 (-)
Lifts pin-1 on the XLR output
®
ProMS2 Microphone Splitter
® True to the Music
USER GUIDE
Radial Engineering Ltd.
1588 Kebet Way, Port Coquitlam BC V3C 5M5
tel: 604-942-1001 • fax: 604-942-1010
info@radialeng.com • www.radialeng.com
ProMS2 ™ User Guide - Part# R870 1056 00 • © Copyright 2013 all rights reserved
Specifi cations and appearance are subject to change without notice.