Page 2
1) Place the Bass Drum flat on the floor to attach the heads and hoops You will want to seat the Beat logo head on the front of the bass drum, closest to where the spurs will be on the shell. Place the hoop on top of the head and make sure it sits evenly.
Page 3
English Bass drum pedal assembly instructions 4) Insert the bass drum beater into the top of the pedal and tighten the wing screw. 5) Insert the pedal into the bottom of the bass drum rim. The base of the pedal will go beneath the bass drum and the clamp will go over the top of the rim.
Page 4
English Rack tom Assembly Instructions 7) Insert the tom arm/holders into the bass casting and tighten them down. 8) Insert the toms into the tom arms and tighten them down using the T-handles on the tom brackets. 9) Once everything is setup you will want to adjust the height of the toms according to the size of the player.
Page 5
English Snare stand assembly instructions 10) Insert the three horizontal arms with the rubber end above the rod of the snare support to keep it still. 11) Adjust the angle of the arms. 12) Place the snare uniformly on the arms.
Page 6
English Hi-At assembly instructions 13) For putting together the Hi Hat stand, begin by folding the three legs on the bottom half of the stand. There is a thin metal upper pull rod that you tighten into the base of the Hi Hat stand. After you’ve done this, place the upper tube over the top of this pull rod and down into the base of the stand.
Page 7
English Cymbal stand assembly instructions 16) Insert the plate holder on the bass drum. 17) Insert the support on the bass drum. Assembly instructions for plates Place the cymbal on top of one of the cymbal felts at the top of the stand, then place the second felt on top of the cymbal.
Page 8
Istruzioni per l’assemblaggio della grancassa 1) Posizionare il tamburo per batteria sul pavimento per fissare teste e cerchi dovrai posizionare la testina del logo Beat sulla parte anteriore della cassa più vicina a dove gli speroni saranno sul guscio. Posizionare il telaio sopra la testa e assicurarsi che si trovi in modo uniforme.
Page 9
Italiano Istruzioni per l’assemblaggio del pedale del tamburo 4) Inserire il battitore del tamburo nella parte superiore del pedale e stringere la vite ad alette. 5) Inserire il pedale sul fondo del bordo del tamburo. La base del pedale andrà sotto la grancassa e il morsetto andrà...
Page 10
Italiano Istruzioni per l’assemblaggio del rack 7) Inserire il braccio del supporto del tom sulla grancassa e serrarli verso il basso. 8) Inserire i tom nei bracci del supporto e stringerli verso il basso usando le maniglie a T sulle staffe del tom. 9) Una volta che tutto è...
Page 11
Italiano Snare stand assembly instructions 10) Inserire sopra l’asta del supporto per il rullante i tre braccetti orizzontali con l’estremità in gomma per tenerlo fermo. 11) Regolare l’angolazione dei braccetti. 12) Posizionare il rullante uniformemente sopra i braccetti.
Page 12
Italiano Hi-At assembly instructions 13) Per mettere insieme il supporto Hi Hat, piegare le tre gambe nella metà inferiore del supporto. Stringere il tirante superiore in metallo sottile nella base del supporto Hi Hat. Posizionare il tubo sopra la parte superiore di questa barra di trazione e verso il basso nella base del supporto.
Page 13
Italiano Istruzioni per l’assemblaggio del piatto 16) Inserire il supporto sulla grancassa. 17) Collocare il piatto sopra uno dei feltri per piatti nella parte superiore del supporto, quindi posizionare il secondo feltro sopra il piatto. Stringere la vite alare nella parte superiore del supporto e sei pronto per suonare.