Table of Contents
Advertisement
Quick Links
230V 1/2 SHEET
SANDER
57941
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper 57941
Summary of Contents for Draper 57941
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page 1.1 Introduction
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS 1. TITLE PAGE INTRODUCTION ......................2 REVISION HISTORY ....................... 2 UNDERSTANDING THIS MANUAL ................2 COPYRIGHT NOTICE...................... 2 2. CONTENTS CONTENTS........................3 3. WARRANTY WARRANTY........................4 INTRODUCTION SCOPE ..........................5 SPECIFICATION ......................5 HANDLING & STORAGE ....................5 HEALTH AND SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE ........6-7 ADDITIONAL SAFETY INSTRUCTIONS FOR SANDERS .......... -
Page 4: Warranty
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms are not authorised. Your Draper warranty is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the warranty period. -
Page 5: Introduction
As part of our core range, this product is suitable for enthusiasts and tradespeople alike. Any application other than that it was intended for, is considered misuse. 4.2 SPECIFICATION Stock No............................57941 Part No...........................1/2S-300D Motor: Rated voltage ........................230V~ Rated frequency ........................ -
Page 6: Health And Safety Information
HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully. -
Page 7: Additional Safety Instructions For Sanders
5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR SANDERS Important: Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. -
Page 8: Connection To The Power Supply
HEALTH AND SAFETY INFORMATION 5.4 CONNECTION TO THE POWER SUPPLY Caution: Risk of electric shock. Do not open. This appliance is supplied with an approved plug and cable for your safety.The value of the fuse fitted is marked on the pin face of the plug. Should the fuse need replacing, ensure the substitute is of the correct rating, approved to BS1362 and ASTA or BS Kite marked. -
Page 9: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION Motor ventilation grilles. Dust collection. Auxiliary handle. Hook and loop pad. Switch locking button. Base. Handle. Conventional front sheet clamps. Power cable. Conventional rear sheet clamps. Trigger switch. - 9 -... -
Page 10: Unpacking And Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing, please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the product. -
Page 11: Basic Sander Operations
BASIC SANDER OPERATIONS SWITCH - FIG. 1 Ensure the sander is raised off the workpiece. To OPERATE press the trigger To use CONTINUOUSLY press trigger , press button and hold in. Release trigger Release button , the machine will continue to run. To STOP the machine press trigger once and button... -
Page 12: Hook And Loop Abrasive Sheet Installation / Replacement
BASIC SANDER OPERATIONS Note: Remove the plug from the socket before carrying out adjustment, servicing or maintenance. HOOK AND LOOP ABRASIVE SHEET INSTALLATION / REPLACEMENT – FIG. 2 The sanding sheets are simply pressed onto the base pad. The holes in the sander must correspond to the holes in the sanding sheet for maximum dust extraction. -
Page 13: Maintenance And Troubleshooting
10. OPTIONAL ACCESSORIES 10.1 OPTIONAL ACCESSORIES A full range of accessory abrasive sheets are available from Draper Tools. Please visit our website for details: www.drapertools.com †Abrasive sheets and the base pad are both considered consumable items. - 13 -... -
Page 14: Disposal
11. DISPOSAL 11.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: ●... -
Page 15: Explanation Of Symbols
12. EXPLANATION OF SYMBOLS 12.1 EXPLANATION OF SYMBOLS Single value noise marking. (Maximum declared A-Weighted Read the instruction manual. sound power level in decibels). Wear face mask and safety Class II construction glasses. (Double insulated). WEEE – Waste Electrical & Wear ear defenders. - Page 16 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the 57941 and is the answer not in the manual?
Questions and answers