Panasonic LS-H Series Instruction Manual

Laser Sensor Head
Thank you very much for purchasing Panasonic products. Read this Instruction Man-
ual carefully and thoroughly for the correct and optimum use of this product. Kindly
keep this manual in a convenient place for quick reference.
● Never use this product as a sensing device for personnel protection.
● In case of using sensing devices for personnel protection, use products which
meet standards, such as OSHA, ANSI or IEC etc., for personnel protection ap-
plicable in each region or country.
● Do not view direct beam by the unprotected eye or with an optical instrument.
Lasers are potentially hazardous.
● Use of control or adjustment or performance of procedures other than those
specified in this instruction manual may result in hazardous radiation expose.
1 INTENDED PRODUCTS FOR CE MARKING
● This product complies with the following standards / regulations.
<EU Directive>
EMC Directive
2 FOR SAFE USE OF A LASER PRODUCT
● In order to prevent the accident by laser product and protect the users, JIS C
6802 "Safety of laser products" was established based on the regulation of
-2014
IEC (International electrotechnical Commission). This regulation classifies laser
products according to the level of hazard, and provides the safety measures for
respective classes.
This product are classified as "Class 1 laser products" according to IEC 60825-
1 (JIS C 6802 ) "Safety of laser products".
-2014 -2014
● Laser hazardous class
Classification according to IEC 60825-1
Class Description of hazardous evaluation
Class 1 Safe under reasonably foreseeable conditions of operation
● Label
• The following label is affixed on this product in accordance with the Safety of laser
product.
Certification / Identification label
● Label position
INSTRUCTION MANUAL
LS-H□
CMJE-LSH100 No.0059-58V
WARNING
(JIS C 6802 )
-2014 -2014
Warning label
3 PART DESCRIPTION
LS-H101□
Operation indicator (Orange) Operation indicator (Orange)
Lights up when the output is ON Lights up when the output is ON
4 MOUNTING
LS-H101□
● The tightening torque should be 0.98N·m or
less.
LS-H102□
● In case mounting this device, use a metal
plate MS-EXL2-2 (accessory).
● The tightening torque should be 0.5N·m or
less with M3 screws.
● In case using the dedicated sensor mounting bracket MS-EXL2-1 (optional) when
mounting this device, the metal plate MS-EXL2-2 (accessory) is required depend-
ing on the mounting direction. Mount as the diagram below indicates.
<Not requiring the metal plate>
Metal plate
(Accessory of MS-EXL2-1)
LS-H201□, LS-H901□
● The tightening torque should be 0.2N·m or less.
Metal plate
(Accessory of MS-LS-1)
19mm
● When placing the sensor horizontally or vertically, the reflector must also be posi-
tioned horizontally or vertically as shown in Fig. 1 below.
If the sensor is placed horizontally or vertically but the mirror is tilted as shown in
Fig. 2 below, the reflection amount will decrease, which may cause unstable de-
tection.
<Fig. 1 Proper positioning>
• When placing the sensor horizontally or vertically, the reflector shall also be posi-
tioned horizontally or vertically.
<Fig. 2 Improper positioning>
• When placing the reflector tilted even when the sensor is positioned horizontally
or vertically.
LS-H102□ LS-H201□, LS-H901□
Operation indicator (Orange)
Lights up when the output is ON
12mm Attached toothed lock washer
M6
Mounting plate
Metal plate
MS-EXL2-2 (Accessory)
13mm
t0.8mm
8.2mm
M3 screw
(Purchase separately)
<Requiring the metal plate>
Sensor mounting bracket
Metal plate
MS-EXL2-1 (Optional)
MS-EXL2-2 (Accessory)
M3 (length: 14mm) screw
with washer
(Accessory of MS-EXL2-1)
14mm
Sensor mounting bracket
MS-LS-1 (Optional)
M2 (length: 12mm)
screw with washer
(Accessory of MS-LS-1)