Master MAS-B301 Instruction Manual page 7

Description:
·
Skeleton: PP or polyamide
·
Frame: PP, brake - PP
·
Inner boot: with synthetic leather, inner core - polyurethane foam
·
Wheels: 82A PU coated, bearings ABEC-5
Proper use and maintenance of skates:
·
The skates are intended for recreational use only, not for jumps and competition. The guarantee will not be valid if problems with the
quality are caused during use by a third person, selling or renting to third parties rather than personal use, or if the skates are damaged
because of improper use.
·
The skates are designed for riding on a flat and firm surface, preferably smooth asphalt or concrete surface. Riding on unsuitable surface
(rough asphalt, concrete, sand, gravel, pavement, etc.) may damage or disproportionately wear the skates.
·
Given the skates allow very fast ride, we recommend caution with regard to your abilities and fitness. We recommend using protectors.
For this equipment, check with your dealer. With young children, we recommend constant supervision of parents or other adults.
·
Before riding, always make sure that all the bolts are tightened, regularly check the condition of the brakes and replace the worn out
ones. Check the state of wear of the wheels. When uneven riding on one side, turn the wheels 180 degrees.
·
These skates are not suitable for children under 20 kg of weight. Do not allow children less than 8 years to ride without adult supervision.
Protective equipment:
They cannot prevent all accidents, but will reduce the risk. We recommend using a helmet, wrist, knee
and elbow pads. All protective equipment must fit properly. This means that you must have the
appropriate size and they must be set correctly. Putting on should be done under adult supervision. We
also recommend using reflective elements attached to the body.
Size setting: Release the laces and all buckles. Safety button for setting the size is located in the front part
of the skate. See picture. Press and hold it. Push the front part of the boot forwards or backwards until
you reach the desired size. Check the tightness by trying to move the boot without pressing the button.
Always set the same size for both skates.
Wheels replacing: To replace use Allen wrench number 4. Use the same sizes of the wheels, with which
were the skates provided. We recommend using PU wheels that are of better quality and have better
driving characteristics.
Bearings replacing: To replace use the supplied Allen wrench number 4. Remove the wheel, push the
bearings out. To replace use bearings 608Z, ABEC1-ABEC7. ABEC 7 bearings are the best.
Operating instructions
·
On the skates cannot be made any change that can negatively affect the safety.
·
Skating is limited by law on road transport. We recommend to ride on suitable surfaces (flat, clean, dry and if possible aside from other
road users). Avoid skating on wet, greasy and dusty surfaces.
·
Before each ride, check the attachment of the wheels and make sure all the bolts are tightened. Tighten any loose screws. For this
purpose use a Phillips screwdriver of the correct size. Wipe dirt and dust with a dry cloth.
·
Check the worn-out wheels. To enjoy the wheels to its maximum, change regularly the front wheels for the rear and vice versa, in case of
uneven riding on one side, rotate the wheel to 180 °.
·
By any malfunction it is necessary to stop using immediately the skates to avoid any damage; there is the risk of potential injury of the
skater.
·
DO NOT USE THE SKATES AT TEMPERATURES BELOW 5 ° C, AT NIGHT AND IN WET CONDITIONS.
·
Frequent use can cause the cheaper types of skates bearings release and wheels wearing. This is not an obstacle for further use of the
skates. Wear of these parts is not covered by warranty.
·
Aluminium frames are generally noisier than PP frames. Noise of the skates is directly proportional to the duration of its use (worn
wheels and bearings) and is not a reason for complaint. When driving, PVC wheels and cheaper types of deposits - 608Z, 608ZZ are also
noisier.
INSTRUCTION MANUAL
MAS-B301, MAS-B302, MAS-B303
7
DE