Samsung NX30PRT000 User Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Laptop
  5. NX30PRT000
  6. User manual
Samsung NX30PRT000 User Manual

Samsung NX30PRT000 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
X30 1.0
Notices
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, mechanical photocopying, recording or
otherwise, without the prior written permission of the manufacturer.
The information within this manual is subject to change without notice.
The manufacturer shall not be held liable for technical or editorial errors or omissions
contained in herein; nor for incidental or consequential damages resulting from the
furnishing, performance or use of this material.
Microsoft Windows is a registered trademark of the Microsoft Corporation.
Product names mentioned herein are for identification purposes only, and may be
trademarks and/or registered trademarks of their respective companies.
Macrovision Statement
If your computer has a DVD drive and an analog TV Out port, the following
paragraph applies:
This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Copyright 2003 All rights are reserved
Notices i

Advertisement

Table of Contents
loading

Related Manuals for Samsung NX30PRT000

Summary of Contents for Samsung NX30PRT000

  • Page 1 X30 1.0 Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice. The manufacturer shall not be held liable for technical or editorial errors or omissions contained in herein;...

  • Page 2: Important Safety Information

    Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed.

  • Page 3: Care During Use

    Do not put rechargeable batteries or products powered by non-removable rechargeable batteries in the garbage. Contact the Samsung Helpline for information on how to dispose of batteries that you cannot use or recharge any longer. Follow all local regulations when disposing of old batteries.

  • Page 4: Laser Safety

    Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard.

  • Page 5: Regulatory Compliance Statements

    Regulatory Compliance Statements Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device.
  • Page 6 In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated.

  • Page 7: United States Of America

    United States of America Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 8: Fcc Part

    The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on.
  • Page 9 If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
  • Page 10 Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté...
  • Page 11 Telecommunications per DOC notice (for products fitted with an IC-compliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users’...

  • Page 12: European Union

    European Union The following information is only applicable to systems labeled with the CE mark European Directives This Information Technology Equipment has been tested and found to comply with the following European directives: • EMC Directive 89/336/EEC with amending directives 92/31/EEC & 93/68/ EEC as per –...
  • Page 13 European States qualified under wireless approvals: Austria, Belgium, Denmark, Finland, France (with frequency Germany, Greece, Ireland, Italy, Luxembourg, The restrictions), Netherlands, Portugal, Spain, Sweden and the United Kingdom. Accept EU Iceland, Liechtenstein, Norway and Switzerland European States with restrictions on use: In France, the frequency range is restricted to 2446.5-2483.5 MHz for devices above 10 mW transmitting power such as wireless LAN.

  • Page 14: Using Your Documentation

    Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows® XP operating system. Whether you are new to using a portable computer or are an experienced user, this user’s manual can help you get the most from your computer. Manual Documentation Conventions Information Icons Four icons and their associated messages appear in this manual.

  • Page 15: Touchpad Conventions

    CD-ROM Device Naming Convention In many installation programs you will have to get a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD.

  • Page 16: Getting Started

    Getting Started Introducing Your Computer The photographs used in this user manual may be somewhat different in shape and color to those of your computer depending on the model of your computer. Front View LCD Panel Hot Keys (p14) Scroll Wheel / Fingerprint Sensor (Optional) Speaker...

  • Page 17: Right View

    Right View Headphone Jack Microphone Jack Left View Fan Vent Modem Port (p32) 4 Users Manual CD-RW/DVD-ROM Drive (p23) Monitor USB Port (2.0) Port LAN Port PCMCIA Card Slot (p33) (p30) USB Ports (2.0) 1394 Port...

  • Page 18: Back View

    Mini-PCI Compartment Compartment Removing or disassembling the hard disk drive will void your warranty. To replace the hard disk drive, please contact your nearest Samsung Service Centre. Wireless LAN/Bluetooth module(optional) is installed in the mini PCI compartment. Security Lock Port (p77)

  • Page 19: Turning The Computer On And Off

    Turning the Computer On and Off To turn on the computer 1. Insert the battery and connect the AC adapter according to the Installation Guide. 2. Slide the LCD latch to the right and open the LCD panel. 3. Press the power button. To turn off the computer 1.
  • Page 20 If the computer does not turn off properly due to a system error, press <Ctrl>+<Alt>+<Delete>. When [Windows Task Manager] dialog box appears, click Shut Down > Turn Off to turn off the computer. Your unsaved work may be lost/damaged. If <Ctrl>+<Alt>+<Delete> keys do not operate either, press the power button for more than 4 seconds to turn off the computer.

  • Page 21: Using The Keyboard

    Using the Keyboard Your computer has an 87/88-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function Embedded Numeric Keypad Windows Although the layout of the keys on your computer’s keyboard is different from that on a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you use it.

  • Page 22: Using The Numeric Keypad

    To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and the surface around the keys. Do not allow liquid to drip into the keyboard or you may damage the keyboard. Using the Numeric Keypad Your keyboard includes a numeric keypad, which is a group of keys that you can set to type numbers and mathematical symbols, such as the plus sign.

  • Page 23: Using Special Function Keys

    Using Special Function Keys The function key activates special functions when it is pressed in combination with another keys. Table 2 shows the special key combinations. <Fn> Key Key Name Combinations <Esc/Rest> Rest <F2/ > Gauge <F4/ LCD/CRT> LCD/CRT <F6/ Mute> Mute <F7/ S/PDIF>...

  • Page 24: Using The Touchpad

    Using the Touchpad In Windows, you always see a small graphical image on the screen that indicates the location where you can take the next action. This image is called a pointer, and is usually displayed in arrow shape ( ) or ‘I’...
  • Page 25 You can use various actions with your touchpad as described below. Action Move Click Double-Click Right-Click Drag 12 Users Manual Function Process Move the pointer Place your finger on the touchpad and slide your finger to a destination. Select an object, open a menu, or Place the pointer over an object, execute a button then press left touchpad button...
  • Page 26 Action Function Scroll Display upper/lower/left/right part of the content within a window (Applicable to certain programs only) Make sure to use your finger to move the pointer with the touchpad. Do not use any sharpened tool because it may damage your touchpad. Scroll Wheel Use If the scroll wheel does not function properly, install the touchpad driver provided on the system software CD.

  • Page 27: Hot Keys

    Hot Keys Icon Name Internet Button E-Mail Button User1 Button WLAN/Bluetooth User 2 Button Using Wireless LAN/Bluetooth Button Loading or unloading wireless LAN/Bluetooth driver takes about 5 seconds. Therefore, if you turn wireless LAN/Bluetooth on/off using the wireless LAN/ Bluetooth button, the button does not work for 5 seconds. (For wireless LAN/ Bluetooth installed models) What is Bluetooth? Bluetooth is a worldwide standard for the wireless exchange of data between...
  • Page 28 Changing the Hot Key Setting You can change the program that will be launched when you press a hot key. As default, Windows Calculator is configured to launch when you press the User 1 button. You can set the program by completing the following procedure. 1.

  • Page 29: Reading The Status Indicators

    Reading the Status Indicators Name Num Lock Caps Lock Scroll Lock Battery Power 16 Users Manual Function Turns on when the numeric keypad is activated. Turns on when the user has set the option for typing letters in upper case. Turns on when it is set to scroll the screen up and down while the cursor position does not change in some applications.

  • Page 30: Adjusting Lcd Brightness

    Adjusting LCD Brightness There are 8 levels of LCD brightness (1: Dimmest ~ 8: Brightest). Press <Fn>+< > or <Fn>+< brightness. When changed, the current LCD brightness is displayed on the top left corner of the LCD screen for a few seconds. The changed brightness setting is maintained after restarting the computer.

  • Page 31: Adjusting The Volume

    Adjusting the Volume To adjust using keyboard Press <Fn>+< To adjust using volume control program Click the Volume icon( level. For advanced volume control options, double-click the Volume icon ( the volume level in the volume control program. 18 Users Manual >...

  • Page 32: Introducing Windows

    Introducing Windows Understanding the Desktop The desktop is the working area on the computer. It consists of the large workspace and a taskbar at the bottom. Shortcut Icons Start Menu Start Button Start Button Taskbar Recycle Bin Language Bar Taskbar System Tray with Clock Opens the Start menu.

  • Page 33: Understanding The Start Menu

    Understanding the Start Menu The Start menu includes everything that is required to start Windows. From the Start menu it is possible to run a program, open a file, assign system users with Control Panel, receive support by clicking Help and Support, and search desired items from the computer or Internet by clicking Search.

  • Page 34: Understanding A Window

    Understanding a Window A window is the basic component in working with the computer. The My Computer window, which is a window for the computer's hard drive, will be used as an example here to show the basic composition of a window. Click Start >...

  • Page 35: Help And Support Center

    Help and Support Center Help and Support Center provides references and troubleshooting information regarding computer use. Click Start > Help and Support. Windows XP Tour You can tour elementary functions provided by Windows XP. Click Start > Tour Windows XP. Or click Start >...

  • Page 36: Using The Computer

    Using the Computer Using the CD Drive You have a CD-RW/DVD-ROM drive installed in your computer. To insert a CD 1. Press the eject button on right side of the CD drive. 2. When the tray slides out, place a CD onto the tray with the label facing up, and push the CD down until it clicks.
  • Page 37 Emergency Eject Hole To eject a CD when the CD drive is not working or the computer is turned off, unfold a clip, and insert the unfolded end of the clip into the emergency eject hole (located next to the eject button) and press until the CD tray opens. To clean a CD or DVD title Clean the disc with a soft clean cloth by wiping from the center outwards.
  • Page 38 To play a video CD If a video CD does not run automatically, follow these steps. 1. Insert a video CD into the CD drive. 2. When the CD drive window appears, double-click the MPEGAV folder. 3. Double-click the .dat file. 4.
  • Page 39 4. In My Computer window, select files and folders to copy, then drag and drop them onto the CD drive window. 5. Click Write these files to CD in the CD drive window. 6. When the CD Writing Wizard appears, enter the CD label, and click Next. The data begins copying.
  • Page 40 Enjoying Home Theater (S/PDIF Port) Your computer supports 5.1 channel output, which is a basic function for home theater systems, and DVD drive. It provides 3D surround sound and vivid screen. What is a home theater system? Home theater system usually consists of a TV, DVD, 5.1 channel speaker, and a digital amp which provides a high-resolution screen (MPEG2) and 3D surround sound (Dolby 5.1 or DTS).
  • Page 41 Step 1. Connect 5.1 channel speaker system to your computer 1. Connect an amplifier to the S/PDIF port on the back of your computer. 2. Connect speakers to the amplifier. (Refer to the speaker system’s manual.) 3. To watch through a TV, connect the TV, and change the display device to the TV in the Display Properties.
  • Page 42 Step 3. Enable S/PDIF in the DVD program To use 5.1 channel speakers, you need to install the Power DVD program from the DVD Installation CD provided with your computer, then change the settings as per the following. 1. Run Power DVD program and click the Settings icon ( 2.

  • Page 43: Using The Pcmcia Card Slot

    Using the PCMCIA Card Slot Various different functions can be added by inserting PCMCIA cards into the system. This system supports 16/32 bit, type I or II PCMCIA card types. The PCMCIA card slot does not support a ZV card or a PCMCIA III card. To insert a PCMCIA card Before using the PCMCIA slot, remove the slot protector.
  • Page 44 Using the Memory Stick Slot Memory Stick is popular as a removable storage device similar to a floppy diskette. It is widely used for many digital products like digital cameras, PDAs, etc. Users can easily install a memory stick to save and remove data on it. First decide the necessary capacity of storage for actual usage and then purchase separately the right amount of memory stick.

  • Page 45: Connecting To The Internet

    Connecting to the Internet Connecting with a Modem Before Start: • Prepare a telephone line that is not digital. • Contact an internet service provider (ISP) for instructions on how to connect to and disconnect from the Internet. 1. Connect a telephone line to the computer’s modem port. 2.
  • Page 46 Connecting Through a Wired LAN 1. Connect a LAN cable to the computer’s LAN port. 2. Click Start > Control Panel. 3. Click Network and Internet Connections in the [Control Panel] window. 4. Click Network Connections in the [Network and Internet Connections] window. 5.
  • Page 47 6. On the General tab, select “Internet Protocol(TCP/IP)” and click Properties. 7. To use DHCP: On the General tab, select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click OK. To use a static IP: On the General tab, select “Use the following IP address” and fill in the IP address, Subnet mask, Default gateway, Preferred DNS server, and Alternative DNS server fields.
  • Page 48 Connecting Through a Wireless LAN (Option) A wireless network (Wireless LAN) environment is a network environment that enables communication between multiple computers at home or a small-size office through wireless LAN devices. Using the wireless network connections between the systems, you can use normal network functions such as sharing of files, folders and printers.

  • Page 49: Connecting To An Access Point (Ap)

    networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet. For details, see “Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 37. Connecting to an Access Point (AP) This section describes how to connect to an AP.
  • Page 50 If the network key is not configured for the desired AP, select 'Allow me to connect to the selected wireless network, even though it is not secure’. Now you are connected to the AP, and you can access the network. Checking the connection status Move the mouse pointer over the Wireless Network Connection ( the taskbar, and the connection status is displayed.
  • Page 51 Step 1. Setting up a computer-to-computer network 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks. 2. Click Advanced. 3. On the Wireless Network tab, click Advanced. 4. Clear 'Automatically connect to non-default network' check box, if it is selected. Select 'Computer-to-computer (ad hoc) networks only', and click Close.
  • Page 52 6. Enter the network name (e.g. samsung), and unselect 'The key is provided for me automatically'. Enter the encryption key in the Network key field, and click OK. To prevent a network connection from an unauthorized user, it would be better to configure a network key (encryption key).
  • Page 53 7. Check that the configured network name (e.g. samsung) is in the ’Preferred networks’ item, and click OK. Now your wireless network setup has been completed. Step 2. Connecting to the configured computer 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks.
  • Page 54 If the network key is not configured in ”Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 37, select 'Allow me to connect to the selected wireless network, even though it is not secure'. The two computers are connected and are able to communicate with each other. When the computers are connected, the 'Wireless Network Connection' message is displayed for a short time over the Wireless Network Connection icon of the two computers.
  • Page 55 Using Wireless Networks in Other Operating Systems In a operating system other than Windows XP, you have to install additional wireless LAN configuration program, and configure wireless network settings. To use wireless network connection, complete the following procedures. • Step1. Install the wireless LAN configuration program (PROSet). •...

  • Page 56: Security Settings

    To connect to an Access Point: To connect to an access point or existing computer-to-computer (Ad Hoc) network, refer to the following procedures. (To create a new computer-to-computer network, refer to the following ∀To create computer-to-computer (Ad Hoc) network∀ section.) 1.
  • Page 57 - Data encryption (WEP): IEEE 802.11 WEP (Wired Equivalent Privacy) standard has two security levels of 64-bit key (40-bit key for some cases) and 128-bit key. - Key index: Select the current encryption key index used by the access point out of 1 to 4.
  • Page 58 3. Configure password setting to be used for computer-to-computer network connection in the Security Settings window. To connect to an access point, enter the network authentication, data encryption (WEP), key index, and password configured in the access point. It is recommended to configure data encryption for security purposes when creating a computer-to-computer network connection profile.

  • Page 59: Using Network Services

    Using Network Services While the computer is connected to the network, you can use network services to share files, folders, and printers. Using computer-to-computer wireless networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet.
  • Page 60 Step 1. Configuring Sharing 1. Right-click the target file or folder to share in My Computer, and select Sharing and Security. 2. Click 'IF you understand the security risks but want to share files without running the wizard, click here'. It has the same security effect as that of the 'Network Setup Wizard'.

  • Page 61: Sharing Printers

    Step 2. Using Shared Files or Folders This section describes how to access shared files or folders if your computer is a member of the same workgroup. 1. Click Start > My Computer. Under Other Places, click My Network Places in your computer.
  • Page 62 Step 1. Configuring Printer Sharing 1. From the computer connected to the printer, click Start > Printers and Faxes. 2. Right-click the printer you want to share, and click Sharing. 3. Select 'Share this printer', enter a share name for the shared printer, and click OK. 4.
  • Page 63 5. Select 'Browse for a printer', and click Next. 6. Select the workgroup or computer, select the desired printer, and click Next. If you cannot find the desired printer, try again after a while. 7. Read the warning about a shared printer, and click Yes to install the shared printer. 8.

  • Page 64: Sharing An Internet Connection

    Sharing an Internet Connection Using computer-to-computer (peer-to-peer) network connections, you can access the Internet through a computer connected to the Internet even if your computer is not directly connected to the Internet. To share an Internet connection, the computers should be connected to a computer-to-computer (peer-to-peer) wireless network.
  • Page 65 If the computer is connected to the Internet through a wired LAN, select 'Local Area Connection'. 3. On the Advanced tab, select 'Allow other network users to connect through this computer's Internet connection', and click OK. Step 2. Checking the Shared Internet Connection. When the Internet connection sharing configuration has been completed, the network icon in the Network Connections window is displayed as follows: Click Start >...

  • Page 66: Using Bluetooth (Optional)

    Using Bluetooth (Optional) Bluetooth is an industry standard for local area wireless data exchange between devices. To use Bluetooth, both of the two Bluetooth devices must be accessible through a wireless connection. Bluetooth enables you to do the following tasks. •...

  • Page 67: Installing The Bluetooth Software

    Installing the Bluetooth Software To use Bluetooth, you have to install the driver and the Bluetooth Manager program. 1. Insert the system software CD in the CD drive on the right side of the computer, and select Install Bluetooth Software. 2.

  • Page 68: Connecting With Other Devices

    Connecting with Other Devices This section describes the common steps when using Bluetooth. Read this section first before reading any other instructions. A Bluetooth connection consists of a client requesting a connection, and a server approving the connection. When you establish a Bluetooth connection, you need to enter a PIN (Personal Identification Number) code in both the client and the server, and the server has to approve the transmission for actual data transmission.

  • Page 69: Transferring Files And Folders

    4. The same window appears on the client, enter the same password as on the server, and click OK. Now a connection between the client and the server has been established. Step 2. Approving a Transmission 1. When a notification window requesting access privilege appears in the Bluetooth icon on the taskbar of the server, click the notification window.

  • Page 70: Connecting With A Hid

    Connecting with a HID You can connect and use an HID (Human Interface Device) with Bluetooth capability such as a keyboard, a mouse, or a joystick on your computer. 1. Configure the HID so it can be searched. For more information refer to the HID user manual.

  • Page 71: Synchronizing Personal Information

    Synchronizing Personal Information You can synchronize personal information saved in the PIMS of your computer such as e-mail, a phonebook, a schedule, or memo with another Bluetooth device. What is PIMS? PIMS (Personal Information Management System) is software that manages personal information such as e-mail, schedules, etc.

  • Page 72: Customizing Your Computer

    Customizing Your Computer Using System Setup The System Setup (BIOS) program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in battery-maintained CMOS memory that saves the information even when the computer’s power is turned off.

  • Page 73: Starting System Setup

    Starting System Setup To start System Setup, turn on your computer and then press <F2> and hold until the System Setup screen appears. Menu Main Advanced Security Boot Exit To open the menu you need to use, use the left or right arrow keys to select the menu name.

  • Page 74: Changing Booting Priority

    Changing Booting Priority You can select the booting priority among the devices such as the hard drive, CD-ROM drive, etc. The following example describes how to configure the hard drive as the first booting device when the CD-ROM drive is configured as the first booting device by default.

  • Page 75: Setting The User Password

    Do not lose or forget your password. If you have forgotten your password, contact the Samsung service center. 1. Select the Security menu in the System Setup. To enter System Setup, see “Starting System Setup” on page 60.

  • Page 76: Deactivating The Password

    Activating the Booting Password Before activating the booting password, the supervisor password must have been configured. Set the Password on boot option to [Enabled]. From now on, system booting will not proceed without the password. Activating the Hard Disk Drive Password Activating the hard disk drive password prevents the currently installed hard disk drive from being used in other systems.
  • Page 77 Configuring Resolution and Colour Depth Screen resolution is the number of pixels displayed on the screen. High resolution makes the overall screen area large, although individual items appear small. Colour quality is determined by the number of bits used to represent a pixel on the screen. High colour quality displays more number of colours on your screen.

  • Page 78: Using External Display Devices

    Using External Display Devices Using external display devices such as monitors, projectors, TVs, etc allows you to view screen images alternatively or simultaneously on each device. Additionally, you can extend the screen onto two display devices to use a larger workspace. Using external display devices is especially useful when you are giving a presentation or watching a movie through your TV.

  • Page 79: Using Dual View To View Extended Screen

    Using Dual View to View Extended Screen You can expand the screen into two display devices and work conveniently in separate workspaces. In Dual View mode, you can select the screen resolution and colour quality for each display device, as if there were two separate graphics cards. 1.
  • Page 80 secondary display device is indicated as '2'. Now you can view the screen through two monitors. 1 : Primary When using Dual View, only the LCD is configured as the primary display device. If the screen of the secondary display device is displayed at 640x480 pixels, with 256 colours, change the settings to the desired screen resolution and colour quality in the [Display Properties] dialog box.

  • Page 81: System Management

    System Management Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance.
  • Page 82 Everything in memory gets saved to the HDD, and the monitor and hard disk get turned off. By default, the power scheme is configured to SAMSUNG mode. SAMSUNG mode extends the battery life and optimizes the Intel Speedstep function.To use...
  • Page 83 If You Reinstall Windows: You should re-establish hibernate in power options by opening Options Properties window and click on the Hibernate tab then click “Enable Hibernation”. Frequent Interruptions: If you experience frequent interruptions, you might also consider putting your computer into automatic hibernation after a specified number of minutes using the power management options.
  • Page 84 Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Control Panel > Performance and Maintenance. 2.

  • Page 85: Using The Battery

    Using the Battery Please refer to the following instructions when running the computer on battery power without connecting the AC power. Please read the instructions on the battery before use. Please refer to the system operation environment (p105) of this manual and operate and store the battery at room temperature.

  • Page 86: Monitoring The Battery Charge

    Using the bridge battery Your computer has a bridge battery, which supplies power for a short time even when there is no battery installed. Thus you can exchange a battery in standby mode, without turning the computer completely off. When you are exchanging the battery in standby mode, exchange in 3 minutes.

  • Page 87: Battery Calibration

    Battery Calibration Calibrating your battery once a month is one of the recommended methods of increasing your computer’s battery life. To calibrate the battery complete the following steps: Calibration Notes: You should start the battery calibration process with a fully charged battery, battery status LED is green.

  • Page 88: Upgrading Memory

    Upgrading Memory This computer has a 128 MB or 256 MB memory module. There is a socket in which one additional memory module can be installed. Removing the memory module Before removing/replacing the memory module, turn the system off completely. Do not replace the memory module when the system is in Rest/ Standby mode.

  • Page 89: Adding A Memory Module

    Adding a memory module 1. Align the new memory module connectors accordingly and slide it into the slot at ° a 30 angle. 2. Push the memory module in until the module clicks into place. If the memory module is not fixed completely, push the memory while pressing the memory module tabs outward.

  • Page 90: Using The Security Lock Port

    Using the Security Lock Port The security lock is a device used to physically 'fix' the system when using it in a public place. The locking device needs to be purchased separately. The shape and methods of use may differ depending on the manufacturer. Please refer to the manual provided with the security lock for proper use.

  • Page 91: Tips For Using Your Computer

    Do not try to disassemble your computer. Opening the system chassis or removing the hard disk drive voids your warranty. Only an authorised Samsung service center can replace or add any parts inside the chassis. • Follow all the instructions and cautions in your computer user documentation.

  • Page 92: Handling Spills

    LCD screen cleaner. Do not use water, window cleaner, acetone, aromatic solvent, or dry, rough towels to clean it. Some liquids damage the polarized LCD screen. If your screen is damaged, contact your local authorized Samsung service center for a replacement. System Management 79...

  • Page 93: Storing The Computer For Long Periods

    Storing the Computer for Long Periods If possible, leave the power cord connected to the computer and an electrical outlet when the computer is not in use. This extends the life of the battery and keeps the battery fully charged. If you will not be using the computer for a long period of time (a month or more), you should charge the battery until it is completely full.

  • Page 94: Troubleshooting

    To run Norton AntiVirus proceed as follows: Click Start > All Programs > Norton AntiVirus > Norton AntiVirus 2002. The Norton Antivirus Subscription on your Samsung notebook will expire within 3 months. It is your responsibility to update the virus definitions, and renew subscription with Symantec when the subscription expires.

  • Page 95: Questions And Answers

    System Recovery Precaution: Before you start restoring your windows operating system insure you backup all data on your hard drive. Samsung is NOT responsible for any data loss. Questions and Answers This section provides information on possible problems, solutions and other references for system use.

  • Page 96: Display Related

    Display Related Q1 The LCD screen is blank. Adjust the LCD screen brightness. Use the <Fn+Up Arrow>, <Fn+Down Arrow> keys. Q2 The screen saver disturbs screen viewing during Media Player or video file operation. Under the Media Player Options, in Player > Enable Screen Saver During Use, uncheck the box and restart the player.
  • Page 97 Q6 In the following cases, the screen blinks or displays noise for a short time: (Clicking the nView tab, changing the resolution, changing the display device, removing the AC adapter, restarting the system, or changing the PowerMizer level) This may happen while the video driver is examining the connected device. Q7 When I connect a projector, and change the setting to display screen image on both the LCD and the projector by pressing <Fn>+<F4 / LCD/CRT>...
  • Page 98 Click Settings tab > Advanced > GeForce FX Go5200 32M/64M tab in the [Display Properties] dialog box. Select the nView Display Mode item, and then configure Display to 'Analog Display'. Right-click on the Analog display device figure, and then click on Screen Adjustment.

  • Page 99: Modem Related

    Modem Related Q1 I cannot hear the modem sound. Check that the telephone line is properly connected to the modem. Check that the modem driver is installed properly. Click Start > Control Panel > Performance and Maintenance > System. Select Hardware tab > Device Manager > Modems in the System Properties window, and check if there is a yellow exclamation mark on the installed modem icon.
  • Page 100 - Using an AT command As an initialization command, use the command, ATX3. Otherwise, enter the ATX3 command manually before making a call. It can correct this problem by skipping the dial tone check step. - Configuring the Modem through the Control Panel Click Start >...
  • Page 101 Under See Also, click Phone and Modem Options. In the Modems tab, select the installed modem, and click Properties. In the Power Management tab of the Modem Properties window, select the "This device activates the computer in power saving mode" check box, and click OK. The above setting enables the modem to turn on the system and receive a fax when in power saving mode.

  • Page 102: Wired Lan Related

    Wired LAN Related Q1 <Wake On LAN> function <Wake On LAN> is a function that activates the system in rest mode when a signal (such as ping or magic packet commands) arrives from network (wired LAN). To use <Wake On LAN> function: Click Start >...

  • Page 103: Wireless Lan Related

    Wireless LAN Related Q1 The Wireless LAN device is operating properly, but I cannot connect to the Internet or to another computer. This is due to an incorrect configuration, or a configuration error. Check the following check lists: If you are using a computer-to-computer (Ad Hoc) network connection, check that the name of the configured network (SSID) is correct.
  • Page 104 WPA Q815485 patch provided by Microsoft requires 802.11x, RADUIS, and authentication server. Also the patch requires the AP and the driver to support the patch. The current version of the driver does not support the WPA function. Click Start > Control Panel > Add or Remove Programs. If you can find the Q815485 patch in the [Add or Remove Programs] window, uninstall the patch before use.
  • Page 105 Q5 In the Windows XP 'Available wireless networks' window, the Wireless Network Connection is displayed as 'Not Available'. Check that the specific program for a wireless LAN connection is installed. Windows XP supports wireless LAN connections through the Wireless Zero Configuration (WZC) service.
  • Page 106 through a computer-to-computer (Ad Hoc) network should be configured so that their IP addresses are within the same subnet range. - If the IP address is configured to DHCP (Obtain an IP address automatically) in TCP/IP properties, IP address is configured within the same subnet range automatically.
  • Page 107 Q12 An established wireless LAN connection is disconnected after 2~3 minutes, and the connection is not recovered. This may be caused by channel interference. Change the channel of the AP, and reconnect. This may be caused by selecting the ’Use IEEE 802.1x network authentication’ option when IEEE 802.1x authentication is not available.

  • Page 108: Games And Programs Related

    Games and Programs Related Q1 3D game is not executed, or some functions are not working. Change the graphic setting of the game to '2D' or 'Software Renderer', then execute the program again. Q2 I launched a game right after installing it, and the game is not executed. This problem may occur when the game is not compatible with Windows XP.
  • Page 109 Q6 While running a game, <Fn>+<F4 / LCD/CRT> keys may not work or screen may not be displayed properly when the keys are pressed. While running Direct3D game, display device configuration keys do not work to maintain the system stability. Since display device control varies depending on the type of display devices in some games, the screen may not displayed properly.

  • Page 110: Restoring The System

    Restoring the System This description is only for models running Window XP. The System Restore function allows you to restore your computer to an earlier copy (called restore point), and restores the settings if a problem occurs.The System Restore function is provided by Windows XP to enable the resolution of various problems without reinstalling Windows XP completely.

  • Page 111: Returning Your Computer To An Earlier Restore Point

    2. Select "Create a restore point", and click Next. 3. In the Restore point description box, type a name to identify the restore point, and than click Create. A restore point has been created. Returning your computer to an earlier restore point The procedures to return your computer to an earlier restore point when a problem has occurred are described below.

  • Page 112: Undoing The Last Restoration

    3. Select the desired restore date from the calendar restoration and select the desired restore point from the list, and then click Next. The date of the restore point is displayed in bold font. 4. Confirm the selected restore point and click Next. System Restore shuts down Windows, and starts the restoration processes.

  • Page 113: Reinstalling Software

    Reinstalling Software If you have reinstalled the Windows operating system, or the system and program do not operate properly, you can re-install the driver and program using the system software CD. The drivers and programs included in the system software CD are listed in the D:\ReadMe.htm file.

  • Page 114: Installing Programs

    Installing programs 1. In the initial screen, click Application Installation. 2. Click Standard installation in the program installation screen (standard installation is recommended). • Standard installation: Installs and recovers programs to the state of shipment. • User installation: You can select the program installation location, and other options for the program installation.

  • Page 115: Reinstalling Windows Xp

    Reinstalling Window may delete the data on the hard disk drive such as files, programs, etc. In order to minimize damage from data loss, please remember to always back up data. Samsung Electronics is not liable in the case of data loss, please consult your warranty statement for clarification.
  • Page 116 3. The description for the standard installation appears. Click Yes. The installation starts, and the system will be restarted after a while. 4. After the system has restarted, the message ’Press any key to boot from CD’ appears. Do not press any key at this time. After a while the partition configuration screen appears.
  • Page 117 If You Cannot Run Windows If you cannot run Windows, you have to boot the system with the system recovery CD, and reinstall Windows. If you boot the system from the system recovery CD, you can install Windows only with the user installation option. You cannot install with the standard installation option.

  • Page 118: System Specification

    Specifications System Specification The following is the basic hardware specification for the purchased product. Variations may exist depending on the model type. Item Specification Intel Pentium M 1.3~1.7GHz / Dothan Cache memory 1MB(Pentium M)/2MB(Dothan) Main memory 128/256/512/1024 MB DDR SDRAM, 2 DDR socket Main Chipset Odem+ / ICH4M Hard disk drive (HDD) 2.5’’, UltraDMA 100, S.M.A.R.T 9.5mmH...

  • Page 119: Product Specification

    Wireless LAN Specification (Optional) Product Specification Item Physical Specifications Power Specification Network Specifications Radio Specifications RF Band Support Channels Device Modulation Scheme Standard Output Power Transmission Rate Antenna Type 106 Users Manual Detailed Specifications Dimensions (Width X Height) 59.75 X 44.45 mm operation temperature and Same as system operation humidity...
  • Page 120 Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country. In France however, use only 4 channels (channel 10, 11, 12, 13) when using wireless networks. • Standard: IEEE 802.b •...
  • Page 121 Abbreviations A ..Amperes AC ..Alternating current ACPI ..Advanced Configuration and Power management Interface APM ..Advanced Power Management ATA.
  • Page 122 ISA ..Industry Standard Architecture KB ..Kilobytes kg ..Kilograms LAN..Local-area network lb..
  • Page 123 Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
  • Page 124 CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts).

  • Page 125: Hard Drive

    Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer.
  • Page 126 PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed.
  • Page 127 Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer.

  • Page 128: Using Windows 2000

    Using Windows 2000 Samsung notebook provides Windows XP or 2000 as operating system depending on the product model. Because the use of Windows XP is similar to Windows 2000, the same User Guide (Online Manual) is used regardless of operating system installed on your notebook.

  • Page 129: Reinstalling Windows 2000

    Introducing Windows Descriptions presented in ”Introducing Windows” (p 19) are applicable only to Windows XP. For Windows 2000, location of menus, shape of icons and some uses may differ from those of Windows XP. To Playback Audio or Video CD Just insert your audio or video CD into your CD drive.

This manual is also suitable for:

Nx30prd000Nx30rh02xaNx30

Table of Contents