1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Laptop
  5. NP28
  6. User manual

Samsung NP28 User Manual

Hide thumbs Also See for NP28:
Table of Contents

Advertisement

Quick Links

Download this manual
P28 1.0
Notices
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, mechanical photocopying, recording or
otherwise, without the prior written permission of the manufacturer.
The information within this manual is subject to change without notice.
The manufacturer shall not be held liable for technical or editorial errors or omissions
contained in herein; nor for incidental or consequential damages resulting from the
furnishing, performance or use of this material.
Microsoft Windows is a registered trademark of the Microsoft Corporation.
Product names mentioned herein are for identification purposes only, and may be
trademarks and/or registered trademarks of their respective companies.
Macrovision Statement
If your computer has a DVD drive and an analog TV Out port, the following
paragraph applies:
This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Copyright 2003 All rights are reserved
Notices i

Advertisement

Table of Contents
loading

Related Manuals for Samsung NP28

Summary of Contents for Samsung NP28

  • Page 1 P28 1.0 Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice. The manufacturer shall not be held liable for technical or editorial errors or omissions contained in herein;...

  • Page 2: Important Safety Information

    Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed.

  • Page 3: Care During Use

    Do not put rechargeable batteries or products powered by non-removable rechargeable batteries in the garbage. Contact the Samsung Helpline for information on how to dispose of batteries that you cannot use or recharge any longer. Follow all local regulations when disposing of old batteries.

  • Page 4: Laser Safety

    Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard.

  • Page 5: Regulatory Compliance Statements

    Regulatory Compliance Statements Wireless Guidance Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz Band, may be present (embedded) in your notebook system. The following section is a general overview of considerations while operating a wireless device.
  • Page 6 In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated.

  • Page 7: United States Of America

    United States of America Unintentional Emitter per FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 8: Fcc Part

    The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on.
  • Page 9 If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
  • Page 10 Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté...
  • Page 11 Telecommunications per DOC notice (for products fitted with an IC-compliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users’...

  • Page 12: European Union

    European Union The following information is only applicable to systems labeled with the CE mark European Directives This Information Technology Equipment has been tested and found to comply with the following European directives: • EMC Directive 89/336/EEC with amending directives 92/31/EEC & 93/68/ EEC as per –...
  • Page 13 European States qualified under wireless approvals: Austria, Belgium, Denmark, Finland, France (with frequency Germany, Greece, Ireland, Italy, Luxembourg, The restrictions), Netherlands, Portugal, Spain, Sweden and the United Kingdom. Accept EU Iceland, Liechtenstein, Norway and Switzerland European States with restrictions on use: In France, the frequency range is restricted to 2446.5-2483.5 MHz for devices above 10 mW transmitting power such as wireless LAN.

  • Page 14: Using Your Documentation

    Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows® XP operating system. Whether you are new to using a portable computer or are an experienced user, this user’s manual can help you get the most from your computer. Manual Documentation Conventions Information Icons Four icons and their associated messages appear in this manual.

  • Page 15: Touchpad Conventions

    CD-ROM Device Naming Convention In many installation programs you will have to install a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD.

  • Page 16: Getting Started

    Getting Started Introducing Your Computer The photographs used in this user manual may be somewhat different in shape and colour to those of your computer depending on the model of your computer. Front View LCD Latch Status Indicators (p 15) Power Button Keyboard (p 8) Touchpad (p12)

  • Page 17: Right View

    Right View Left View LAN Port Modem Port (p30) (p29) 4 Users Manual CD Drive(Option, (p 22) Battery USB Ports (2.0) Microphone Jack PCMCIA Card Slot Headphone Jack TV-Out Port (S-VHS)

  • Page 18: Back View

    Back View Monitor Port DC Jack USB Ports (2.0) Fan Vent Security Lock Port Bottom View CPU Bay Memory Bay Battery Cover Latch Getting Started 5...

  • Page 19: Turning The Computer On And Off

    Turning the Computer On and Off To turn on the computer 1. Insert the battery and connect the AC adapter according to the Installation Guide. 2. Slide the LCD latch to the right and open the LCD panel. 3. Press the power button. To turn off the computer 1.
  • Page 20 If the computer does not turn off properly due to a system error, press <Ctrl>+<Alt>+<Delete>. When [Windows Task Manager] dialog box appears, click Shut Down > Turn Off to turn off the computer. Your unsaved work may be lost/damaged. If <Ctrl>+<Alt>+<Delete> keys do not operate either, press the power button for more than 4 seconds to turn off the computer.

  • Page 21: Using The Keyboard

    Using the Keyboard Your computer has an 88/89-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function Windows Embedded Numeric Keypad Although the layout of the keys on your computer’s keyboard is different from that on a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you use it.

  • Page 22: Using The Numeric Keypad

    To clean the computer keyboard, use slightly damp cotton swabs. Scrub the keys and the surface around the keys. Do not allow liquid to drip into the keyboard or you may damage the keyboard. Using the Numeric Keypad Your keyboard includes a numeric keypad, which is a group of keys that you can set to type numbers and mathematical symbols, such as the plus sign.

  • Page 23: Using Special Function Keys

    Using Special Function Keys The function key activates special functions when it is pressed in combination with another keys. Table 2 shows the special key combinations. <Fn> Key Key Name Combinations <Esc/ > Rest <F2/ > Gauge <F4/ > LCD/CRT <F6/ >...
  • Page 24 < > Volume Up Increases the audio volume. Getting Started 11...

  • Page 25: Using The Touchpad

    Using the Touchpad In Windows, you always see a small graphical image on the screen that indicates the location where you can take the next action. This image is called a pointer, and is usually displayed in arrow shape ( ) or ‘I’...
  • Page 26 You can perform various actions with your touchpad as described below. Action Move Click Double-Click Right-Click Drag Function Process Move the pointer Place your finger on the touchpad and slide your finger to a destination. Select an object, open a menu, or Place the pointer over an object, execute a button then press left touchpad button...
  • Page 27 Make sure to use your finger to move the pointer with the touchpad. Do not use any sharpened tool because it may damage your touchpad. 14 Users Manual...

  • Page 28: Reading The Status Indicators

    Reading the Status Indicators Name Function Num Lock Turns on when the numeric keypad is activated. Caps Lock Turns on when the user has set the option for typing letters in upper case. Scroll Lock Turns on when it is set to scroll the screen up and down while the cursor position does not change in some applications.

  • Page 29: Adjusting Lcd Brightness

    Adjusting LCD Brightness There are 8 levels of LCD brightness (1: Dimmest ~ 8: Brightest). Press <Fn>+< brightness. When changed, the current LCD brightness is displayed on the top left corner of the LCD screen for a few seconds. Whenever you change the power source the brightness level changes according to the settings.

  • Page 30: Adjusting The Volume

    Adjusting the Volume To adjust using keyboard Press <Fn>+< > or <Fn>+< To adjust using volume control program Click the Volume icon( level. For advanced volume control options, double-click the Volume icon ( the volume level in the volume control program. >...

  • Page 31: Introducing Windows

    Introducing Windows Understanding the Desktop The desktop is the working area on the computer. It consists of the large workspace and a taskbar at the bottom. Shortcut Icons Start Menu Start Button Start Button Taskbar Recycle Bin Language Bar 18 Users Manual Taskbar System Tray with Clock Opens the Start menu.

  • Page 32: Understanding The Start Menu

    Understanding the Start Menu The Start menu includes everything that is required to start Windows. From the Start menu it is possible to run a program, open a file, assign system users with Control Panel, receive support by clicking Help and Support, and search desired items from the computer or Internet by clicking Search.

  • Page 33: Understanding A Window

    Understanding a Window A window is the basic component in working with the computer. The My Computer window, which is a window for the computer's hard drive, will be used as an example here to show the basic composition of a window. Click Start >...

  • Page 34: Help And Support Center

    Help and Support Center Help and Support Center provides references and troubleshooting information regarding computer use. Click Start > Help and Support. Windows XP Tour You can tour elementary functions provided by Windows XP. Click Start > Tour Windows XP. Or click Start >...

  • Page 35: Using The Computer

    Using the Computer Using the CD Drive You have one of following drives installed in your computer. CD-ROM drive DVD-ROM drive CD-RW/DVD-ROM Combo drive DVD Dual Drive To insert a CD 1. Press the eject button on right side of the CD drive. 2.
  • Page 36 If you remove the CD when the CD access LED is on, the disk and the data in it may be damaged. Emergency Eject Hole To eject a CD when the CD drive is not working or the computer is turned off, unfold a paperclip, and insert the unfolded end of the clip into the emergency eject hole (located next to the eject button) and press until the CD tray opens.
  • Page 37 To play a video CD If a video CD does not run automatically, follow these steps. 1. Insert a video CD into the CD drive. 2. When the CD drive window appears, double-click the MPEGAV folder. 3. Double-click the .dat file. 4.
  • Page 38 4. In My Computer window, select files and folders to copy, then drag and drop them onto the CD drive window. My Computer window 5. Click Write these files to CD in the CD drive window. 6. When the CD Writing Wizard appears, enter the CD label, and click Next. The data begins copying.

  • Page 39: Using The Pcmcia Card Slot

    Using the PCMCIA Card Slot Various different functions can be added by inserting PCMCIA cards into the system. This system supports 16/32 bit, type I or II PCMCIA card types. The PCMCIA card slot does not support a ZV card or a PCMCIA III card. To insert a PCMCIA card Before using the PCMCIA slot, remove the slot protector.

  • Page 40: Using Samsung Smart Screen

    If you select OK, the program is automatically launched when you start your computer. 2. Samsung Smart Screen appears. When you run the program for the first time, water drop image is displayed.

  • Page 41: Using Samsung Theme

    Using Samsung Theme Samsung Theme is a program that enables a user to easily switch a theme (desktop, logon screen and sound effect). Double-click the Samsung Theme ( (Or select Start > All Programs > Samsung Software > Samsung Theme >...

  • Page 42: Connecting To The Internet

    Connecting to the Internet Connecting with a Modem Before Start: • Prepare a telephone line that is not digital. • Contact an internet service provider (ISP) for instructions on how to connect to and disconnect from the Internet. 1. Connect a telephone line to the computer’s modem port. 2.
  • Page 43 Connecting Through a Wired LAN 1. Connect a LAN cable to the computer’s LAN port. 2. Click Start > Control Panel. 3. Click Network and Internet Connections in the [Control Panel] window. 4. Click Network Connections in the [Network and Internet Connections] window. 5.
  • Page 44 6. On the General tab, select “Internet Protocol(TCP/IP)” and click Properties. 7. To use DHCP: On the General tab, select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click OK. To use a static IP: On the General tab, select “Use the following IP address” and fill in the IP address, Subnet mask, Default gateway, Preferred DNS server, and Alternative DNS server fields.

  • Page 45: Using Samsung Network Manager

    1. Connect LAN cable to the computer's LAN port. 2. Double-click Samsung Network Manager icon on the desktop. Or click Start > All Programs > Samsung Network Manager > Samsung Network Manager. 3. When you are using DHCP, available IP's are displayed in the status dialog box.
  • Page 46 To change network places You can change network places as below. 1. Connect LAN cable to the computer's LAN port, and double-click Samsung Network Manager icon on the desktop. If you used static IP in previous place, previous static IP is displayed in the status dialog box.
  • Page 47 2. Click Change, select a place icon then click Change. 3. On "Do you want to change the location setting?" dialog box, click Ok. 4. When the network place is changed, corresponding place icon is displayed in color and full dialog box appears. In the right area of full dialog box, network setting is displayed.
  • Page 48 Internet. For details, see “Using Network Services” on page 48 The description in this section concerns the Agere Wireless MiniPCI Card (hereafter referred to as a 11b card) and the SAMSUNG SWL2700 M b/g miniPCI WLAN Adapter (hereafter referred to as a 11g card).

  • Page 49: Connecting To An Access Point (Ap)

    An AP is a network device that bridges wired and wireless LANs, and corresponds to a wireless hub in a wired network. You can connect multiple wireless LAN installed computers to an AP. 2) Computer-to-computer (ad hoc) This is also called a peer-to-peer network. In computer-to-computer wireless networks, you can wirelessly connect 2 or more computers that have wireless LAN modules.
  • Page 50 2. Select your desired AP (e.g. Test) to connect, and enter the encryption key for the AP in the Network key field, and click Connect. If the network key is not configured for the desired AP, select 'Allow me to connect to the selected wireless network, even though it is not secure’.
  • Page 51 Connecting to computer-to-computer networks ad hoc) In computer-to-computer wireless networks, you can wirelessly connect 2 or more computers that have wireless LAN modules. Using this method, a computer that is not connected to the Internet can share the Internet by accessing another computer connected to the Internet.
  • Page 52 Step 1. Setting up a computer-to-computer network 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks. 2. Click Advanced. 3. On the Wireless Network tab, click Advanced. 4. Clear 'Automatically connect to non-default network' check box, if it is selected. Select 'Computer-to-computer (ad hoc) networks only', and click Close.
  • Page 53 6. Enter the network name (e.g. samsung), and unselect 'The key is provided for me automatically'. Enter the encryption key in the Network key field, and click OK. To prevent a network connection from an unauthorized user, it would be better to configure a network key (encryption key).
  • Page 54 7. Check that the configured network name (e.g. samsung) is in the ’Preferred networks’ item, and click OK. Now your wireless network setup has been completed. Step 2. Connecting to the configured computer 1. Right-click on the Wireless Network Connection ( select View Available Wireless Networks.
  • Page 55 If the network key is not configured in ”Connecting to computer-to-computer networks (peer-to-peer or ad hoc)” on page 38, select 'Allow me to connect to the selected wireless network, even though it is not secure'. The two computers are connected and are able to communicate with each other. When the computers are connected, the 'Wireless Network Connection' message is displayed for a short time over the Wireless Network Connection icon of the two computers.
  • Page 56 Using a wireless network with the wireless LAN setup program.(for an 11b card) For operating systems other than Windows XP, the installation of the wireless LAN setup program and the configuration of the wireless network environment are required. For an 11g card, see (p 45). To use a wireless network, complete the following procedures.
  • Page 57 For information about the encryption key (WEP key) of your AP, ask your AP administrator or network administrator. A network key consists of either 5 or 13 alphanumeric characters(e.g. magic), or 10 or 26 hexadecimal(0-9 or A-F). 6. When your computer is connected to an access point, the connection ( appears in front of the added wireless network connection profile name.
  • Page 58 on the Profile Name. Then the Activate or Edit a Preferred Profile window appears. Select Activate Profile and then click OK. Using a wireless network with the wireless LAN setup program.(for an 11g card) For operating systems other than Windows XP, the installation of the wireless LAN setup program and the configuration of the wireless network environment are required.
  • Page 59 1. Double-click an access point (or Ad Hoc network) name from Available Networks or click on Configure. If your desired network does not appear, click Refresh. An access point is represented by the ( represented by the ( 2. Enter Profile Name to use for the network connection. 3.
  • Page 60 To create a computer-to-computer (Ad Hoc) network: To create a new computer-to-computer (Ad Hoc) network or to connect to a hidden access point (Stealth/Closed Mode), refer to the following procedures. A hidden access point is an access point that exists, but is configured not to be detected by the scan operation to prevent access attempts from unauthorized users.

  • Page 61: Using Network Services

    Using Network Services While the computer is connected to the network, you can use network services to share files, folders, and printers. Using computer-to-computer wireless networks, you can access the Internet through a computer that is connected to the Internet even if your computer is not directly connected to the Internet.
  • Page 62 Step 1. Configuring Sharing 1. Right-click the target file or folder to share in My Computer, and select Sharing and Security. 2. Click 'If you understand the security risks but want to share files without running the wizard, click here'. It has the same security effect as that of the 'Network Setup Wizard'.

  • Page 63: Sharing Printers

    Step 2. Using Shared Files or Folders This section describes how to access shared files or folders if your computer is a member of the same workgroup. 1. Click Start > My Computer. Under Other Places, click My Network Places in your computer.
  • Page 64 Step 1. Configuring Printer Sharing 1. From the computer connected to the printer, click Start > Printers and Faxes. 2. Right-click the printer you want to share, and click Sharing. 3. Select 'Share this printer', enter a share name for the shared printer, and click OK. 4.
  • Page 65 5. Select 'Browse for a printer', and click Next. 6. Select the workgroup or computer, select the desired printer, and click Next. If you cannot find the desired printer, try again after a while. 7. Read the warning about a shared printer, and click Yes to install the shared printer. 8.
  • Page 66 Sharing an Internet Connection by a wireless LAN Using computer-to-computer (peer-to-peer) network connections, you can access the Internet through a computer connected to the Internet even if your computer is not directly connected to the Internet. To share an Internet connection, the computers should be connected to a computer-to-computer (peer-to-peer) wireless network.
  • Page 67 If the computer is connected to the Internet through a wired LAN, select 'Local Area Connection'. 3. On the Advanced tab, select 'Allow other network users to connect through this computer's Internet connection', and click OK. Step 2. Checking the Shared Internet Connection. When the Internet connection sharing configuration has been completed, the network icon in the Network Connections window is displayed as follows: Click Start >...

  • Page 68: Customizing Your Computer

    Customizing Your Computer Using System Setup The System Setup (BIOS) program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in battery-maintained CMOS memory that saves the information even when the computer’s power is turned off.

  • Page 69: Starting System Setup

    Starting System Setup To start System Setup, turn on your computer and then press <F2> and hold until the System Setup screen appears. Menu Main Advanced Security Boot Exit To open the menu you need to use, use the left or right arrow keys to select the menu name.

  • Page 70: Changing Booting Priority

    Changing Booting Priority You can select the booting priority among the devices such as the hard drive, CD-ROM drive, etc. The following example describes how to configure the hard drive as the first booting device when the CD-ROM drive is configured as the first booting device by default.

  • Page 71: Setting The User Password

    Do not lose or forget your password. If you have forgotten your password, contact the Samsung service center. 1. Select the Security menu in the System Setup. To enter System Setup, see “Starting System Setup” on page 56 2.

  • Page 72: Deactivating The Password

    Activating the Booting Password Before activating the booting password, the supervisor password must have been configured. Set the Password on boot option to [Enabled]. From now on, system booting will not proceed without the password. Activating the Hard Disk Drive Password Activating the hard disk drive password prevents the currently installed hard disk drive from being used in other systems.
  • Page 73 Configuring Resolution and Colour Depth Screen resolution is the number of pixels displayed on the screen. High resolution makes the overall screen area large, although individual items appear small. Colour quality is determined by the number of bits used to represent a pixel on the screen. High colour quality displays more number of colours on your screen.

  • Page 74: Using External Display Devices

    Using External Display Devices Using external display devices such as monitors, projectors, TVs, etc allows you to view screen images alternatively or simultaneously on each device. Additionally, you can extend the screen onto two display devices to use a larger workspace. Using external display devices is especially useful when you are giving a presentation or watching a movie through your TV.
  • Page 75 Configuring the Display Properties In the Display Properties, you can configure detailed display settings. For example, you can configure the LCD to a primary device and the CRT to a secondary device by completing the following procedures. 1. Connect the monitor to the monitor port of the computer. 2.

  • Page 76: Using Dual View To View Extended Screen

    Using Dual View to View Extended Screen You can expand the screen into two display devices and work conveniently in separate workspaces. In Dual View mode, you can select the screen resolution and colour quality for each display device, as if there were two separate graphics cards. 1.
  • Page 77 4. When the configuration is complete, click Identify on the left side of Troubleshoot. The primary display device(the LCD) is indicated as '1', and the secondary display device is indicated as '2'. Now you can view the screen through two monitors. When using Dual View, only the LCD can be configured as the primary display device.

  • Page 78: System Management

    System Management Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance.
  • Page 79 66 Users Manual By default, the power scheme is configured to SAMSUNG mode. SAMSUNG mode extends the battery life and optimizes the Intel Speedstep function.Since the CPU power consumption is automatically lowered...
  • Page 80 If You Reinstall Windows: You should re-establish hibernate in power options by opening Options Properties window and click on the Hibernate tab then click “Enable Hibernation”. Frequent Interruptions: If you experience frequent interruptions, you might also consider putting your computer into automatic hibernation after a specified number of minutes using the power management options.
  • Page 81 Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Control Panel > Performance and Maintenance. 2.

  • Page 82: Using The Battery

    Using the Battery Please refer to the following instructions when running the computer on battery power without connecting the AC power. Please read the instructions on the battery before use. Please refer to the system operation environment (p104) of this manual and operate and store the battery at room temperature.

  • Page 83: Monitoring The Battery Charge

    Monitoring the Battery Charge To monitor using a shortcut key Press <Fn>+<F2/ To monitor in control panel Click Start > Control Panel > Performance and Management > Power Options > Power Meter tab. Power source and remaining battery charge are displayed. Using the battery The battery has an expendable supply, so when you use it for a long time, the capacity/battery life is shortened.

  • Page 84: Battery Calibration

    Battery Calibration Calibrating your battery once a month is one of the recommended methods of increasing your computer’s battery life. To calibrate the battery complete the following steps: Calibration Notes: You should start the battery calibration process with a fully charged battery, battery status LED is green.

  • Page 85: Upgrading Memory

    Upgrading Memory Your computer has one or more memory modules installed and a total of two memory slots available. Below is an explanation on how to remove the memory and replace it with a new one. Removing the memory module Before removing/replacing the memory module, turn the system off completely.

  • Page 86: Adding A Memory Module

    Adding a memory module 1. Align the new memory module connectors accordingly and slide it into the slot at ° a 30 angle. Ensure the notch on the memory module corresponds with the notch on the socket. 2. Push the memory module in until the module clicks into place. If the memory module is not fixed completely, gently push the memory down while pressing the memory module tabs outward.

  • Page 87: Replacing The Hard Disk Drive

    Replacing the Hard Disk Drive The procedures for replacing the hard disk will be described below. 1. Turn off the computer and turn upside down. 2. Using a screwdriver, remove the screw securing the hard disk, and pull out the hard disk bracket.
  • Page 88 Insert the bracket into the hard disk compartment, and secure it using the screw. After replacing the hard disk Referring to ”Reinstalling Windows XP” (101), reinstall Windows, and reinstall the drivers and programs referring to ”Reinstalling Software” (99). System Management 75...

  • Page 89: Using The Security Lock Port

    Using the Security Lock Port The security lock is a device used to physically 'fix' the system when using it in a public place. The locking device needs to be purchased separately. The shape and methods of use may differ depending on the manufacturer. Please refer to the manual provided with the security lock for proper use.

  • Page 90: Tips For Using Your Computer

    The following information helps you avoid potential problems as you use your computer: Do not try to disassemble your computer. Opening the system chassis voids your warranty. Only an authorised Samsung service center can replace or add any parts inside the chassis. •...

  • Page 91: Handling Spills

    LCD screen cleaner. Do not use water, window cleaner, acetone, aromatic solvent, or dry, rough towels to clean it. Some liquids damage the polarized LCD screen. If your screen is damaged, contact your local authorized Samsung service center for a replacement. 78 Users Manual...

  • Page 92: Storing The Computer For Long Periods

    Storing the Computer for Long Periods If you will not be using the computer for a long period of time (a month or more), you should discharge the battery completely then remove the battery from the computer. This extends the life of the battery. System Management 79...

  • Page 93: Troubleshooting

    Recovery CD to reinstall OS and System Software CD to reinstall the corrupt device drivers. System Recovery Precaution: Before you start restoring your windows operating system insure you backup all data on your hard drive. Samsung is NOT responsible for any data loss. 80 Users Manual...

  • Page 94: Questions And Answers

    Questions and Answers This section provides information on possible problems, solutions and other references for system use. Windows Related Q1 The system does not shutdown properly. When the system does not shutdown normally, press and hold the Power button until the system manually shuts off. If the Power-Saving Mode is configured into the Power button, press and hold for more than 4 seconds to shut the system off.

  • Page 95: Display Related

    Display Related Q1 The LCD screen is blank. Adjust the LCD screen brightness. Use the <Fn+ Q2 The screen saver disturbs screen viewing during Media Player or video file operation. Under the Media Player Options, in Player > Enable Screen Saver During Use, uncheck the box and restart the player.
  • Page 96 Q7 Execution of a DOS command such as DIR causes the desktop to momentarily appear as a broken image when using the system in 2-byte character language DOS mode. This may happen when you have configured the display in such a way that the screen is displayed to both the LCD and CRT screens simultaneously.

  • Page 97: Modem Related

    Modem Related Q1 I cannot hear the modem sound. Check that the telephone line is properly connected to the modem. Check that the modem driver is installed properly. Click Start > Control Panel > Performance and Maintenance > System. Select Hardware tab > Device Manager > Modems in the System Properties window, and check if there is a yellow exclamation mark on the installed modem icon.
  • Page 98 - Using an AT command As an initialization command, use the command, ATX3. Otherwise, enter the ATX3 command manually before making a call. It can correct this problem by skipping the dial tone check step. - Configuring the Modem through the Control Panel Click Start >...
  • Page 99 Under See Also, click Phone and Modem Options. In the Modems tab, select the installed modem, and click Properties. In the Power Management tab of the Modem Properties window, select the "This device activates the computer in power saving mode" check box, and click OK. The above setting enables the modem to turn on the system and receive a fax when in power saving mode.

  • Page 100: Wired Lan Related

    Wired LAN Related Q1 <Wake On LAN> function <Wake On LAN> is a function that activates the system in rest mode when a signal (such as ping or magic packet commands) arrives from network (wired LAN). To use <Wake On LAN> function: Click Start >...

  • Page 101: Wireless Lan Related

    Wireless LAN Related For basic procedures for using a wireless LAN, refer to '”Connecting Through a Wireless LAN (Option)” (35). Q1 The Wireless LAN device is operating properly, but I cannot connect to the Internet or to another computer. This is due to an incorrect configuration, or a configuration error. Check the following check lists: If you are using a computer-to-computer (Ad Hoc) network connection, check that the name of the configured network (SSID) is correct.
  • Page 102 Q3 I cannot share an Internet connection. It may require some time to synchronize the computers to share an Internet connection after the Internet connection sharing configuration is completed. If you cannot share Internet connection even after a longer period, restart the computer.
  • Page 103 may be affected by the location of the computer. In addition, close distances (less than 5m) between wireless equipment, especially an AP, may result in poor wireless communication quality. A5 Check that the wireless LAN card is recognized by the computer. ‘...
  • Page 104 Ch13) - When the SSID option of an AP is configured to “Hide”, you cannot search for that AP in the computer. Canceling the Hide option of an AP is recommended. An SSID (Service Set ID) is a name for distinguishing a wireless LAN from another wireless LAN.
  • Page 105 Q6 The Wireless network connection operates properly, but the Wireless Network Connection icon on the Taskbar displays the "Disconnected" message. This is one of the known problems when you are using a wireless LAN connection after installing Windows XP service pack 1. For more information, refer to the following link for known problems with Microsoft.
  • Page 106 Q9 The wireless LAN does not operate properly when there are other products operating in the 2.4GHz band. Currently, both the IEEE 802.11b and IEEE 802.11g devices are using the ISM (industrial, scientific, and medical) band. Therefore some channel interference may happen when there are other devices using the same frequency band such as a wireless video transceiver, a microwave oven, etc.

  • Page 107: Games And Programs Related

    Games and Programs Related Q1 3D game is not executed, or some functions are not working. Change the graphic setting of the game to '2D' or 'Software Renderer', then execute the program again. Q2 I launched a game right after installing it, and the game is not executed. This problem may occur when the game is not compatible with Windows XP.
  • Page 108 (It may happen while running Harry Porter and the Chamber of Secrets, Warcraft 3, Unreal Tournament 2003, Starcraft, Quake 3, Soldier of Fortune 2, Heroes of Might and Magic 4, etc.) Q7 Running speed of a game is too slow or fast. Change the setting of Power Schemes to 'Always On'.

  • Page 109: Restoring The System

    Restoring the System This description is only for models running Window XP. The System Restore function allows you to restore your computer to an earlier copy (called restore point), and restores the settings if a problem occurs.The System Restore function is provided by Windows XP to enable the resolution of various problems without reinstalling Windows XP completely.

  • Page 110: Returning Your Computer To An Earlier Restore Point

    2. Select "Create a restore point", and click Next. 3. In the Restore point description box, type a name to identify the restore point, and than click Create. A restore point has been created. Returning your computer to an earlier restore point The procedures to return your computer to an earlier restore point when a problem has occurred are described below.

  • Page 111: Undoing The Last Restoration

    3. Select the desired restore date from the calendar restoration and select the desired restore point from the list, and then click Next. The date of the restore point is displayed in bold font. 4. Confirm the selected restore point and click Next. System Restore shuts down Windows, and starts the restoration processes.

  • Page 112: Reinstalling Software

    Reinstalling Software If you have reinstalled the Windows operating system, or the system and program do not operate properly, you can re-install the driver and program using the system software CD. The drivers and programs included in the system software CD are listed in the D:\ReadMe.htm file.

  • Page 113: Installing Programs

    Installing programs 1. In the initial screen, click Application Installation. 2. Click Standard installation in the program installation screen (standard installation is recommended). • Standard installation: Installs and recovers programs to the state of shipment. • User installation: You can select the program installation location, and other options for the program installation.

  • Page 114: Reinstalling Windows Xp

    Reinstalling Window may delete the data on the hard disk drive such as files, programs, etc. In order to minimize damage from data loss, please remember to always back up data. Samsung Electronics is not liable in the case of data loss, please consult your warranty statement for clarification.
  • Page 115 3. The description for the standard installation appears. Click Yes. The installation starts, and the system will be restarted after a while. 4. After the system has restarted, the message ’Press any key to boot from CD’ appears. Do not press any key at this time. After a while the partition configuration screen appears.
  • Page 116 If You Cannot Run Windows If you cannot run Windows, you have to boot the system with the system recovery CD, and reinstall Windows. If you boot the system from the system recovery CD, you can install Windows only with the user installation option. You cannot install with the standard installation option.

  • Page 117: System Specification

    19.0 V / 3.16A * Please refer to the product catalog or consult your product provider for availability when purchasing optional accessories for this system. 104 Users Manual Samsung Electro-Mechanics SWL-2700m(Mini-PCI) (operation) : 20% ~ 80% Remarks Max 2GB Optional...

  • Page 118: Product Specification

    Wireless LAN Specification (Optional) Agere Wireless Mini-PCI Card Device Product Specification Item Physical Dimensions Specifications operation temperature and humidity Power Specification Power Saving Mode Receiving Mode Transmission Mode Power Network Compatibility Specifications Operating System Media Access Protocol Security * The equipment complies with Wi-Fi wireless LAN security specifications of WPA (Wi-Fi Protected Access). To connect to a wireless network using WPA, the additional installation of certificates or a windows patch (KB826942) is required depending on the network connection environment.

  • Page 119: Radio Specifications

    Radio Specifications RF Band Support Channels Device Modulation Scheme Standard Output Power Transmission Rate* Antenna Type * The data rate may differ from the real data transmission rate. Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country.
  • Page 120 SAMSUNG SWL2700M 11b/g Mini-PCI WLAN Adapter Device Product Specification Item Physical Dimensions Specifications operation temperature and humidity Power Specification Power Saving Mode Receiving Mode Transmission Mode Power Network Compatibility Specifications Operating System Media Access Protocol Security * The equipment complies with Wi-Fi wireless LAN security specifications of WPA (Wi-Fi Protected Access) and CCX (Cisco Compatible eXensions).To connect to a wireless network using WPA and CCX, the additional...
  • Page 121 Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country. In France however, use only 4 channels (channel 10, 11, 12, 13) when using wireless networks. • Standard: IEEE 802.g •...
  • Page 122 Abbreviations A ..Amperes AC ..Alternating current ACPI ..Advanced Configuration and Power management Interface APM ..Advanced Power Management ATA.
  • Page 123 ISA ..Industry Standard Architecture KB ..Kilobytes kg ..Kilograms LAN..Local-area network lb..
  • Page 124 Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
  • Page 125 CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts).

  • Page 126: Hard Drive

    Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer.
  • Page 127 PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed.
  • Page 128 Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer.

  • Page 129: Using Windows 2000

    Using Windows 2000 Samsung notebook provides Windows XP or 2000 as operating system depending on the product model. Because the use of Windows XP is similar to Windows 2000, the same User Guide (Online Manual) is used regardless of operating system installed on your notebook.
  • Page 130 Introducing Windows Descriptions presented in (p 18) are applicable only to Windows XP. For Windows 2000, location of menus, shape of icons and some uses may differ from those of Windows XP. To Playback Audio or Video CD Just insert your audio or video CD into your CD drive. The associated application program will start automatically and playback the audio or video files.

This manual is also suitable for:

Osca

Table of Contents