Epson Stylus TX235 Service Manual page 55

Epson Stylus SX230 series / SX235W series / SX430W series / SX440W series
<Part supply as ASP>
Yes
<Lubrication status when
supplied as ASP>
Not lubricated
<Lubrication Point>
1. Cam of the LD Roller
Assy (contact point with
LD Roller Assy
the Hopper)
2. Cam of the LD Roller
Assy (contact point with
the Paper Back Lever)
<Type>
G-71
<Application Amount>
Circumference of each
cam (0.05 g each)
<Remarks>
Apply with injector.
Lubricate before
attaching the part.
1. Application Point
2. Application Point
Figure 4-4. Lubrication of the LD Roller Assy
PF Roller
Figure 4-8. Lubrication of the PF Roller
Maintenance
<Part supply as ASP>
Frame Base
Yes
<Lubrication status when
supplied as ASP>
Not lubricated
<Lubrication Point>
Contact point (x1 on the
shaft) on the EJ Roller with
the Frame Base
<Type>
G-71
<Application Amount>
0.06 g
<Remarks>
Apply with injector.
Lubricate before
attaching the part.
EJ Roller
Application Point
Figure 4-5. Lubrication of the EJ Roller
<Part supply as ASP>
Yes
<Lubrication status when
supplied as ASP>
Not lubricated
<Lubrication Point>
Contact points (x3 on the
shaft) on the PF Roller
with the Frame Base
<Type>
G-71
<Application Amount>
On each contact point
around the shaft
Frame Base
(appropriate amount)
<Remarks>
Apply with injector.
Lubricate before
attaching the part.
Application Point
Lubrication Points and Instructions
<Part supply as ASP>
Yes
<Lubrication status when
supplied as ASP>
Not lubricated
<Lubrication Point>
EJ Roller Gear Shaft on the EJ Roller Gear
<Type>
G-71
<Application Amount>
φ 1 mm x 1 circle
<Remarks>
Using injector, apply
grease along the tier on
the shaft.
Lubricate before
attaching the part.
Application Point
Figure 4-6. Lubrication of the EJ Roller Gear
<Part supply as ASP>
Yes
<Lubrication status when
supplied as ASP>
Not lubricated
<Lubrication Point>
Contact points (x2) on the
Paper Back Lever with the
Paper Back Lever
Frame Base
<Type>
G-71
<Application Amount>
0.06 g x 2 points
<Remarks>
Apply with injector.
Lubricate before
attaching the part.
Application Point
Figure 4-9. Lubrication of the Paper Back Lever
Revision B
<Part supply as ASP>
None
<Lubrication status when
supplied as ASP>
---
<Lubrication Point>
1. On the bearings (x2) of the
CR Driven Pulley on the
CR Driven Pulley Holder
CR Driven Pulley Holder
2. Contact points (x4) on
the groove of the CR
Driven Pulley Holder
with the Main Frame
<Type>
G-71
<Application Amount>
Appropriate amount
<Remarks>
1. After applying with
injector, attach the CR
Driven Pulley and rotate
it twice to spread grease.
2. Apply with injector.
Wipe the grease that run
off the CR Driven
Pulley Holder.
Check the lubrication
1. Application Point
condition and apply
2. Application Point
grease if necessary.
Figure 4-7. Lubrication of the CR Driven Pulley Assy
Confidential
55