Clemco 1028 Manual
  1. Manuals
  2. Brands
  3. Clemco Manuals
  4. Power Tool
  5. 1028
  6. Manual

Clemco 1028 Manual

Single chamber blast machine
Hide thumbs

Advertisement

Table of Contents

© 2013 CLEMCO INDUSTRIES CORP.
One Cable Car Dr.
Washington, MO 63090
Phone (636) 239-4300
F
(800) 726-7559
ax
Email: info@clemcoindustries.com
www.clemcoindustries.com
SINGLE CHAMBER BLAST MACHINE
MODELS 1028 AND 1042
O. M. 04124
DATE OF ISSUE:
REVISION:
Do not proceed with
these instructions*
until you have READ
the orange cover of
this MANUAL and YOU
UNDERSTAND its
contents.
These WARNINGS are
included for the health
and safety of the
operator and those in
the immediate vicinity.
*If you are using a Clemco Distributor
Maintenance and Part Guide, refer to
the orange warnings insert preceding
the Index before continuing with the
enclosed instructions.
Electronic files include a Preface
containing the same important
information as the orange cover.
01/15/77
K, 07/13
WARNING

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1028 and is the answer not in the manual?

Questions and answers

Related Manuals for Clemco 1028

Summary of Contents for Clemco 1028

  • Page 1 © 2013 CLEMCO INDUSTRIES CORP. One Cable Car Dr. *If you are using a Clemco Distributor Washington, MO 63090 Maintenance and Part Guide, refer to Phone (636) 239-4300 the orange warnings insert preceding (800) 726-7559 Email: info@clemcoindustries.com...
  • Page 2 ANSI Z535.4-1998, to alert the user of a potentially hazardous situation that may be encountered while operating this equipment. ANSI's definitions of the signal words are as follows: © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...
  • Page 3 "...need not be installed directly on a pressure vessel when the source of pressure is external to the vessel © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...
  • Page 4 1.3.6.2 Refer to the table in Figure 2 to determine cfm requirements. The table shows air consumption of nozzles when new. It does not show the recommended © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...

  • Page 5: Initial Setup

    Use a nozzle lined with boron carbide with these abrasives. © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...
  • Page 6 Both the operator and machine tender must wear suitable personal protective equipment including an approved respirator, plus approved eye, face, and hearing protection. © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...
  • Page 7 While holding the lever lock down, press the expelled from the machine and pressure equalizes. control handle lever. Be prepared; blasting will begin as soon as the machine pressurizes. © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...
  • Page 8 Keep the open the choke valve. abrasive level below the pop-up valve to prevent abrasive on the pop-up valve from being forced up and © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...

  • Page 9: Preventive Maintenance

    When an optional air filter is used, inspect the filter  Check all external piping, control hoses, and valves element, and clean the bowl. for leaks. If leaks are found, stop blasting and repair. © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...

  • Page 10: Service & Maintenance

    All service on the pop-up valve must be done abrasive metering valve. Pressurize the machine to with the compressed air off and the air supply locked-out force out any damp abrasive. and tagged-out. © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...

  • Page 11: Troubleshooting

    Make sure the choke valve is open. The valve is open when the handle is in-line with the piping. 6.3.2 Abrasive metering valve may be open too far. See Section 3.5. © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...

  • Page 12: Replacement Parts

    Screen, 10" diameter ..........03362 Blast hose, 1/2" ID x 25 ft. 2-braid without couplings ..........23750 coupled with 00577 and 00599 ....... 01268 Figure 4 Holder, nozzle, CHE-1/2 ........00577 © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...
  • Page 13 Metering valve, abrasive ......01247 machines as of October 1, 2011. Hard, formed- Coupling, CFA-1/2, 1/2" NPT alum... 00558 pipe pusher lines are no longer available. 3, 4 Figure 5 © 2013 CLEMCO INDUSTRIES CORP.  www.clemcoindustries.com  Manual No. 04124, Rev. K...

This manual is also suitable for:

1042

Table of Contents