BE QUIET! Pure Rock Manual page 2

AMD AM2(+) / AM3(+) / AM4 / FM1 / FM2(+)
General
We recommend preparatory mounting of the
cooler outside the PC case for subsequent
Installation video
installation.
The following parts are needed for this:
1x Pure Rock CPU cooler (1), 1x 120mm fan (2), 2x long AMD
mounting brackets (5), 1x cooler mounting bridge (6), 4x AMD
spacer nuts (9), 2x Intel/AMD mounting bridge fastening
screws (11), 4x AMD backplate screws (13), 2x fan clips (15),
4x AM3 washers (16)
Assembly of the cooler mounting frame
To permit mounting of the cooler please remove both the
plastic retainers of the AMD retention module. The factory-
fitted backplate affixed to the rear side of the motherboard will
be needed for subsequent installation of the cooler.
Note: To mount the Pure Rock (1) on an AM3 motherboard,
please use the four AM3 washers (16), placing these below the
backplate bolts protruding through the front side of the
motherboard.
AM2(+) / AM3(+) / FM1 / FM2(+)
AM4
Place the four AMD spacer nuts (9) onto the backplate bolts
protruding through the front side and affix both long AMD
mounting brackets (5) with the AMD backplate screws (13).
The protective covering on the underneath of the cooler must
be removed prior to installation against the CPU.
Caution: The thermal past supplied is not suitable for human
consumption. If swallowed, drink lots of water and urgently
seek medical attention. Keep it out of the reach of children.
Avoid contact with skin and eyes.
Notes
Mounting the CPU cooler
Position the cooler mounting bridge (6) centrally on the cooler
(1). Next place the cooler unit onto the CPU. Insert the Intel/
AMD mounting bridge fastening screws (11) from above into
the cooler mounting bridge and then screw these alternatively
tight. You can use any cross-tip screwdriver for this.
Fasten the 120mm fan (2) onto the cooler unit (1) using fan
clips (15). Connect the fan to the motherboard's PWM signal.
When dismantling the fan (2), push the notches of the fan
clips (15) away from the fan..
Limited Warranty
As per the terms and conditions of this limited warranty as given
below, be quiet! warrants its new products to be free of defects
resulting from faulty materials and faulty manufacturing for the length
of the warranty period.
I. APPLICABILITY
This non-transferable warranty is applicable to newly purchased,
previously unopened be quiet! products and is enforceable by only
the original consumer purchaser. Proof of purchase is required for
warranty service, so should be retained. be quiet! does not provide
warranty registration services.
II. WARRANTY PERIOD
For eligible products, parts and labor are warranted for the appli-
cable warranty period from the date of purchase. The applicable
warranty period varies by product model, and is identified in your
user documentation, on the product package, or as listed below.
Should any of these warranty periods differ, the longest specified
warranty period will apply. Replaced products will be warranted
for the remainder of the original warranty period or thirty days,
whichever is longer.
III. EXCLUSIONS
The following are not covered by the warranty:
1. Normal wear and tear.
2. Any product which has been modified without permission from
be quiet!, or on which the serial number or warranty sticker has been
defaced, modified, or removed.
3. Damage, deterioration or malfunction resulting from:
Accident, abuse, misuse or improper use, neglect, connection to
an improper voltage source, unauthorized product modification, or
failure to follow instructions included with the product.
Fire, water, lightning, or other acts of nature.
Repair or attempted repair by anyone not authorized by be quiet!.
Shipping or transport damage (claims must be made with the carrier).
Any other cause which does not relate to a defect in materials or
manufacturing workmanship.
4. Cartons, cases, batteries, cabinets, tapes, accessories or other
consumables used with this product.
5. be quiet!, Inc. does not warrant that this product will meet your
requirements. It is your responsibility to determine the suitability of
this product for your purpose.
6. Removal or installation charges.
7. Shipping charges.
8. Any incidental charges.
IV. EXCLUSION OF DAMAGES
be quiet!'s sole obligation and liability under this warranty is limited
to the repair or replacement of a defective product at its option.
be quiet! shall not, in any event, be liable for any special, incidental,
indirect, or consequential damages whatsoever, including but not
limited to loss of profits, revenue, or data (whether direct or indirect),
damages resulting from interruption of service and loss of business,
or for liability in tort relating to this product or resulting from its use
or possession, even if be quiet! has been advised previously of the
possibility of such damages.
V. LIMITATIONS OF IMPLIED WARRANTIES
There are no other warranties, expressed or implied, including but not
limited to those of merchantability or fitness for a particular purpose.
The duration of implied warranties is limited to the warranty length
specified in Paragraph II.50
VI. LOCAL LAW AND YOUR WARRANTY
This warranty gives you specific legal rights. You may also have other
rights granted under local law. These rights may vary.
VII. NO OTHER WARRANTY
No be quiet! employee, dealer, or other agent is authorized to make
any modification, extension, or addition to this warranty.
VIII. TO OBTAIN TECHNICAL SUPPORT OR WARRANTY SERVICE
Please see your product owner's manual or visit the service section
at www.bequiet.com for details and contact information. You will
need to provide proof of purchase for warranty service.
bequiet.com
bequiet.com