Page 1
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Series 1520/1580/1585 Enclosure General User Manual Revision V1.0 SKU#: UKRR Image above shows the enclosure with door open (Series 1580 shown inside not included). Copyright 2018 - Tyto Robotics Inc.
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Table of contents Chapter 1: Introduction 3 1.1 Item checklist for the enclosure 4 Chapter 2: General Safety Rules 5 Chapter 3: Installation of the Enclosure 6 3.1 Main cage frame 6 ...
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 1.1 Item checklist for the enclosure The Series 1520/1580/1585 enclosure ships with its own package. You may use the following ...
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Chapter 2: General Safety Rules Always put safety first! It is your responsibility! It is always important to stay alert to work with a thrust stand. The enclosure protects the ...
Page 6
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 16. Wait for the propeller to stop spinning before opening the door on the enclosure. Copyright 2018 - Tyto Robotics Inc. Page 6/28 ...
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Chapter 3: Installation of the Enclosure In this chapter, we will present you a full guide to install the enclosure for the Series ...
Page 8
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Please follow these instructions to assemble the main frame: ❏ Open the three-way connector bag (#KXPA) and take out eight three-way connectors ...
Page 9
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Fig 3.2: Assemble the rest four connectors on top of the frame ❏ Open the large corner bracket bag (#QAKQ) and take out four L corner brackets ...
Page 10
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 ❏ Repeat the previous steps to assemble the second L bracket on the other end the ...
Page 11
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Fig 3.5: Integrate the support rails into the enclosure’s base ❏ Now you may fully tighten all fasteners on the three-way connectors and the L corner ...
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 3.2 Meshes on main cage frames In this section, you will need to place the mesh on the frame of the enclosure. Please retrieve ...
Page 13
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Please only retrieve the following quantity from the door holder bag (#NTAP): Item name Item SKU Door holding metal strip LZXH M5 T-nut ZQSS M5 x 15 mm socket head screw CLKD ...
Page 14
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 ❏ Beam #11: Four extra M 4 T-nuts (#ZFLE) facing Z+ (for door hinge, retrieve the ...
Page 15
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Fig 3.8: Applying the mesh onto the enclosure with M5 screws and washers ❏ Repeat the same steps to apply the mesh onto the assigned four surfaces. ❏...
Page 16
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 ❏ Open the small corner bracket bag (#PVPD) and retrieve the small L corner brackets ...
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 3.3 Reclosable door, the hinge and the mesh In this section, you will assemble the door. Please retrieve the following items: Item name Item SKU Located in (SKU# if exist) T-slotted Frame Beam length 535mm TSXN Main Carton Box (#PHJY)
Page 18
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Please retrieve the remaining material in the mesh fastener bag (#QTAQ): Item name Item SKU M5 T-nut ZQSS M5 x 8 mm socket head screw PKDR M5 flat washer APEH ...
Page 19
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Fig 3.12: Installation of the mesh on the door with fasteners ❏ Take out the door handle (#XQUK) and then insert two T-nuts (#ZQSS) on any side of ...
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 3.4 Door assembly on the enclosure In this section, you will install the door assembly onto the enclosure’s main body. Please ...
Page 21
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Fig 3.14: Install the hinge on the enclosure using the T-nuts inserted in the aluminum frame ❏ Place the door on the front face of the enclosure. The door handle should be on the ...
Page 22
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 ❏ Repeat the previous steps to install the second hinge. ❏ Tighten all screws on the hinges, and check that the door can open and close properly ...
Page 23
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Fig 3.17: Use of the metal strip to keep the door open ❏ Tighten all fasteners. The cage is now fully functional. Copyright 2018 - Tyto Robotics Inc. ...
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 3.5 Mounting of the thrust stand and other accessories In this section, you will replace the lower support part of the Series 1520, the Series 1580 or ...
Page 25
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Please follow these instructions to install the thrust-stand into the enclosure: ❏ Replace the lower support with the extended-height lower support in your Series ...
Page 26
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 ❏ Use the M5 x 12 mm screws (#APGU) to hold the thrust-stand onto the beam, but do ...
Series 1520/1580/1585 enclosure user manual Document ID: QOZ4JD Publish date: 2019-03-27 Chapter 4: Final Preparation before Tests 4.1 LiPo battery management If you are using a LiPo battery as the power source of a test, we recommend putting the LiPo ...
Need help?
Do you have a question about the 1520 Series and is the answer not in the manual?
Questions and answers