Thermo Pride OL20FA151T60 Series Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Thermo Pride Manuals
  4. Furnace
  5. OL20FA151T60 Series
  6. Installation and operation manual
Thermo Pride OL20FA151T60 Series Installation And Operation Manual

Thermo Pride OL20FA151T60 Series Installation And Operation Manual

Oil fired furnace
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTALLATION AND OPERATION MANUAL
WITH USERS INFORMATION SECTION
c WARNING
: IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE
OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER APPLIANCE.
c WARNING:
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, OR MAINTENANCE
CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL. FOR ASSISTANCE OR
ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER, OR SERVICE AGENCY.
PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION, INITIAL FIRING, AND BEFORE
PERFORMING ANY SERVICE OR MAINTENANCE. THESE INSTRUCTIONS MUST BE LEFT WITH THE
USER AND SHOULD BE RETAINED FOR FUTURE REFERENCE BY QUALIFIED SERVICE PERSONNEL.
MO-552
ECN 5631-MA 200505
OIL FIRED FURNACE
MODELS:
OL20FA151T60(B/R)
THERMO PRODUCTS, LLC.
PO BOX 237
DENTON, NC 27239
PHONE: 800-476-4328
OL20RA151T60(B/R)
MADE IN USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OL20FA151T60 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Thermo Pride OL20FA151T60 Series

Summary of Contents for Thermo Pride OL20FA151T60 Series

  • Page 1 OIL FIRED FURNACE INSTALLATION AND OPERATION MANUAL WITH USERS INFORMATION SECTION MODELS: OL20FA151T60(B/R) OL20RA151T60(B/R) c WARNING : IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

  • Page 3: Safety Section

    CAUTION: Do not exceed 90° rotation of the flue elbow counter clockwise right from the vertical positon. See Page 2. cWARNING: The predetermined fan and limit locations on all of the Thermo Pride oil fired furnaces have been tested and approved by Thermo Products, LLC. in conjunction with Underwriters Laboratories, Inc.
  • Page 4 All installations and services must be performed by qualified service personnel. This page contains reproductions of the various instruction and warning labels placed on the Thermo Pride Oil Furnaces. Please read and comply with the contents of these labels.
  • Page 5 All installations and services must be performed by qualified service personnel.

  • Page 6: Table Of Contents

    All installations and services must be performed by qualified service personnel. TABLE OF CONTENTS SECTION BEGINNING PAGE I. SAFETY SECTION II. GENERAL INSTRUCTIONS A.VENTING B. DUCT WORK/AIR CONDITIONING C. BURNER INSTALLATION D. FUEL SYSTEM INSTALLATION E. WIRING III. STARTING THE UNIT A.

  • Page 7: General Instructions

    All installations and services must be performed by qualified service personnel. II. GENERAL INSTRUCTIONS - READ BEFORE START OF INSTALLATION 1. The heating output capacity of the furnace proposed for installation should be based on a heat loss calculation made according to the manuals provided by the Air Conditioning Contractors of America (ACCA) or the American Society of Heating, Refrigeration and Air Conditioning Engineers, Inc.

  • Page 8: A.venting

    The OL20 furnace is to be installed on non-combustible flooring only. NOTE: When power venting a Thermo Pride oil fired furnace an isolated combustion air kit (PVB or Beckett boot) is to be used with the other manufacturers power venting system.

  • Page 9: Duct Work/Air Conditioning

    All installations and services must be performed by qualified service personnel. TABLE 1: Suggested sizes and positions of flue pipe opening on left hand side of casing. UNIT DIA. “X” “Y” FLUE DIA. GASKET TRIM COLLAR HOLE DIM. DIM. PART# PART# OL20FA151T60 7-1/2”...

  • Page 10: Burner Installation

    All installations and services must be performed by qualified service personnel. The most common location for the A-shaped coil (A style) is shown in Fig. 2. Fig 2: Acceptable locations for the air conditioner evaporator coil. NOTICE: The minimum coil pan clearance for a sectional or drum type heat exchanger is three inches unless specified otherwise by the individual coil manufacturer.
  • Page 11 Thermo Pride burners. (See Fig. 5). See Thermo Pride burner application chart for type of insulator. Do not allow the burner tube or end cone to physically touch or protrude into the chamber, as excess heat transfer could result in destruction of the tube, end cone or both.

  • Page 12: Fuel System Installation

    All installations and services must be performed by qualified service personnel. Fig. 5: (Side view) Burner insertion illustration D. FUEL SYSTEM INSTALLATION In situations where the oil storage tank is installed at the same level with, or above, the burner, a single oil supply line run from the oil tank to the burner will be usually be adequate.

  • Page 13: Starting The Unit

    All installations and services must be performed by qualified service personnel. III. STARTING THE UNIT A. INITIAL OPERATION OF THE FURNACE WARNING: To avoid possible explosion, DO NOT attempt to light the burner if: 1. Oil has accumulated in the base of the combustion chamber. 2.

  • Page 14: Airflow And Temperature Rise

    All installations and services must be performed by qualified service personnel. to obtain the correct overfire draft reading. See table 2. The draft measured at the flue (stack draft) should read no more than 0.05 in. W.G. NOTICE: The overfire draft is the more important measurement and should be used to adjust the setting of the barometric draft control.

  • Page 15: Troubleshooting And Service

    B. LIMIT POSITION AND LOCATION cWARNING: The predetermined fan and limit locations on all of the Thermo Pride oil fired furnaces have been tested and approved by Thermo Products, LLC. Any attempt to relocate these safety controls or replace these safety controls with a control that is not approved, or is incompatible, may result in personal injury, substantial property damage or death.

  • Page 16: Installer's Instructions To User

    All installations and services must be performed by qualified service personnel. Fig. 6: Typical Heat Exchanger Cleanout Cover Locations. With access to the inside of the heat exchanger through the burner area, clean-out openings, and vent pipe connection, it is possible to use a long, flexible wire brush and an industrial type vacuum cleaner to remove any soot build-up.

  • Page 17: Users Information Section

    All installations and services must be performed by qualified service personnel. The sequence of operation of the furnace. The correct operation and maintenance of the appliance as outlined in the users information manual. That failure to maintain and operate this furnace in accordance with these instructions could result in hazardous conditions, bodily injury, property damage and may void the limited warranty on the furnace.

  • Page 18: Starting The Furnace

    All installations and services must be performed by qualified service personnel. cCAUTION: Do not attempt to make repairs yourself. cWARNING: The area around the furnace should be kept free and clear of combustible liquids and material, especially papers and rags. cWARNING: never burn garbage or refuse in your furnace.
  • Page 19 All installations and services must be performed by qualified service personnel.

  • Page 20: Appendix-A Replacement Parts List

    All installations and services must be performed by qualified service personnel. APPENDIX-A Replacement Parts List Replacement Parts for OL20FA151T60...
  • Page 21 All installations and services must be performed by qualified service personnel.
  • Page 22 All installations and services must be performed by qualified service personnel. Replacement Parts for OL20RA151T60...
  • Page 23 All installations and services must be performed by qualified service personnel.
  • Page 24 All installations and services must be performed by qualified service personnel. Replacement Parts for Beckett Burner...
  • Page 25 All installations and services must be performed by qualified service personnel. Replacement Parts for Riello F5 Burner...

  • Page 26: Appendix-B Wiring Diagrams

    All installations and services must be performed by qualified service personnel. APPENDIX-B Wiring Diagrams...

This manual is also suitable for:

Ol20ra151t60 seriesOl20fa151t60bOl20fa151t60rOl20ra151t60bOl20ra151t60r

Table of Contents