Remote Controller Manual; Remote Controller Specifications; Introduction Of Function Buttons On The Remote Controller; Names And Functions Of Indicators On Remote Controller - Midea MFA-18HRDN1-Q Manual

REMOTE CONTROLLER MANUAL

1. Remote Controller Specifications

Model
Rated Voltage
Lowest Voltage of CPU
Emitting Signal
Reaching Distance
Signal Range
Environment
2. Introduction of Function Buttons on the
Remote Controller
1
SET TEMPERATURE
4
AUTO
COOL
DRY
HEAT
5
MODE
SWING ECONOMIC TIMER ON
AIR DIRECTION
6
7
Fig. 1
TEMP Button : Press the button to decrease the indoor
1
temperature setting.
TEMP Button : Press the button to increase the indoor
2
temperature setting.
ON/OFF Button: Push this button to start the unit operati-
3
on.Push the button again to stop the unit operation.
MODE Select Button:
4
mode is selected in a sequence that goes from AUTO
COOL DRY HEAT and FAN, as the following figure
indicates:
AUTO COOL
COOL only model has no HEAT feature.
SWING Button: Push this button, the louver would swing
5
up and down automatically. Push again to stop it .
RESET Button: Press When the RESET button is
6
pushed, all of the current settings are cancelled and the
control will return to the initial settings.(Use a 1mm little
round stick to push the button )
AIR DIRECTION Button:
7
be fixed at a desired angle. The louver swing(upward
or downward
) to a certain angle for each press. When
the louver swing at an angle which would affect the
cooling and heating efficiency of the air conditioner, it
would automatically change the swing direction (upward
or downward).
R51D/E R51D/CE
3.0V(Alkaline dry batteries LR03
2.0V
8m (when using 3.0 voltage,
it Gets 11m)
-5 ~60
2
O C)
8
FAN
HIGH
MED
LOW
3
TEMP.
9
ON/OFF FAN SPEED
10
RESET LOCK TIMER OFF
POWERFUL
11
12
13
Each time you push the button, a
DRY
HEAT
NOTE
Push this button, the louver can
FAN SPEED Button:
8
Speed in the sequence that goes from AUTO LOW
MED to HIGH, then back to Auto.
TIMER ON Button:
9
ON(start to operate). Each press will increase the time ON
setting in 30 minutes increments. When the setting time
displays 10:00, each press will increase the time ON setting
in 60 minutes increments.To cancel the time ON program,
simply adjust the time ON to 0:00.
2)
ECONOMIC RUNNING Button:
10
Energy-Saving operation mode. Press the button again to
cancel.
11
TIMER OFF Button:
OFF (turn off the operation). Each press will increase the
time OFF setting in 30 minutes increments. When the
setting time displays 10:00, each press will increase the
time OFF setting in 60 minutes increments. To cancel the
time OFF program, simply adjust the time OFF to 0:00
LOCK Button:
12
little round stick to push this button )
POWERFUL Button:
13
mode to go into powerful cooling (heating)operation.Press
again to cancel it.
The unit will automatically revert back to the previous
operational mode after continuously operating under the
powerful cooling mode.
3. Names and Functions of indicators on
Remote Controller
1
2
4
6
7
DIGITAL DISPLAY area:
1
ure and, if in the TIMER mode, will show the ON and OFF
settings of the TIMER. It will automatically revert back to
show the temperature after 5 seconds. Under "FAN" oper-
ation mode,nothing is shown in this area.
FAN
TRANSMISSION Indicator:
2
when remote controller transmits signals to the indoor unit.
ON/OFF Indicator:
3
turned on by the remote controller, and disappears when
the unit is turned off.
OPERATION MODE Indicator:
4
ion modes--"AUTO", "COOL", "DRY", "HEAT" and "FAN".
HEAT only available for heat pump model.
FAN SPEED Indicator:
5
select the desired fan speed setting (Auto-Low-Med- High).
You selection will be displayed in the LCD window except
the Auto fan speed.
LOCK Indicator: This symbol appears when press the
6
LOCK button, and disappears when press it again.
TIMER ON/OFF Display: This display area shows the
7
settings of TIMER. That is, if only the starting time of
operation is set, it will display the TIMER ON. If only the
turning off time of operation is set, it will display the TIMER
OFF. If both operations are set, it will show TIMER ON/ OFF
which indicates you have chosen to set both the starting time
and off time.
This button is used for setting Fan
Press this button to preset the time
Press this button to go into the
Press this button to preset the time
Push this button to lock in all the current
Press this button on cooling/heating
NOTE
Display Panel
3
4
5
TIMER ON/ OFF
This area will show the temperat-
This indicator flashes once
This symbol appears when the unit is
Shows the current operat-
Press the FAN SPEED button to
installation & owner's manual
17