TP-Link TL-WA1201 Quick Installation Manual page 2

Client Mode
Connects your wired devices to a wireless network.
Internet
1. Connect the access point according to Step A to B in the diagram.
2. Turn on the power, and wait until the Wireless LEDs (
3. Use the default SSID and Password printed on the label of the access point to
join its Wi-Fi network.
4. Launch a web browser and enter http://tplinkap.net. Create a password to log in.
Multi-SSID Mode
Creates multiple wireless networks to provide different security and VLAN groups.
Internet
Existing Router
1. Connect the access point according to Step A to D in the diagram.
2. Turn on the power, and wait until the Wireless LEDs (
3. Use the default SSID and Password printed on the label of the access point to
join its Wi-Fi network.
4. Launch a web browser and enter http://tplinkap.net. Create a password to log in.
Power on via the PoE Injector
Power the device with the included passive PoE injector when the access point is located far from a power outlet.
Note: The passive PoE injector supports a cable length up to 30 meters, but the value may vary due to the environment.
Internet
Existing Router
Frequently Asked Questions (FAQ)
Q1. How do I restore the access point to its factory default settings?
• With the access point powered on, use a pin to press and hold the Reset button until the Power LED starts
blinking, then release the button.
Note: Resetting the access point will clear all previous configurations, and the access point will reset to the default Access Point
mode.
Q2. What should I do if I cannot access the web management page?
• If the computer has a static IP address, change its settings to obtain an IP address automatically.
• Verify that http://tplinkap.net or http://192.168.0.254 is correctly entered in the web browser.
• Use another web browser and try again.
• Reboot your access point and try again.
• Power off your host AP and enter http://tplinkap.net in the web browser to try again.
Q3. How do I recover the access point's web management password or retrieve my Wi-Fi password?
• If you forget the password for the web management page, refer to Q1 to reset the access point to its factory
default settings. Then create a new login password.
Host AP's SSID
) are lit and stable.
B
) are lit and stable.
Reset
B A
5. Go to Quick Setup, select Client mode and click Next. Follow the step-by-step
instructions to complete the configuration.
6. Now, connect your wired device to the access point via an Ethernet cable.
Enjoy!
D C A
5. Go to Quick Setup, select Multi-SSID mode and click Next. Follow the
step-by-step instructions to complete the configuration.
6. Go to Settings > Wireless > Wireless Settings to modify VLAN IDs.
7. Now, connect your wireless devices to the Wi-Fi networks isolated by VLANs.
Enjoy!
• If your forget your Wi-Fi password, but are able to log in to the web management page, log in and go to Settings
> Wireless > Wireless Settings to retrieve or reset your Wi-Fi password.
Q4. What should I do if my wireless network is not stable?
This could be caused by interference. You can try the following methods:
• Log in to the web management page. Go to Settings > Wireless > Wireless Settings and change your wireless
channel to a different one.
• Move the access point to a new location away from Bluetooth devices and other household electronics, such as
cordless phones, microwaves, and baby monitors to minimize signal interference.
Safety Information
• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device.
• Do not use any other chargers than those recommended.
• Do not use damaged charger or USB cable to charge the device.
• Do not use the device where wireless devices are not allowed.
• Adapter shall be installed near the equipment and shall be easily accessible.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or
damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
For technical support, the user guide and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
TV
OR
VLAN 1
SSID 1 for VLAN 1
SSID 2 for VLAN 2
VLAN 2
SSID 3 for VLAN 3
VLAN 3
TL-WA1201's SSID
Passive PoE Injector
Other
OR
Wired
Device