Connection Diagram; Important Installation Information; Connection Possibilities - Honeywell PEHA 952 JRM Installation Instruction

PehA elektro gmbh & co. kg
Postfach 1727 • D-58467 Lüdenscheid • Tel.: (02351)185-0 • Fax: (02351)27666 • e-mail: peha@peha.de • Internet: www.peha.de
blind/roller shutter module
GB Installation instruction Compact

Important installation information !

• Read through the operating instructions carefully before putting the device into service!
• Only use 1-phase power supply with a 10A overload release. (terminal L, N  230V~/50 Hz)!
• Make sure the polarity of the motors is correct! After connecting the motors, switch to central UP. When not all of the motors move UP, check the motors'
connections and polarity!
• Auto mode for the outputs can be activated and deactivated at a switch on input I32 of the JRM module. This requires the corresponding outputs to be
assigned to input I32 (see AUTO MODE instructions).
caution !!
• Only one motor (max. 1A) may be connected to each output (e.g. motor M0: O0 = motor DOWN, O1 = motor UP)! The manufacturer's operating
instructions must be observed when installing the motors.
• Use separate connections for the control and motor lines! They may not be laid together in one wiring connection.
• Wiring connections must not run behind the JRM for EMC reasons!
• The 24V inputs are connected to the JRM's 24V supply voltage. Make sure that no connections are joined to any alternating current circuits (230V~).
This can cause a defect in the Compact JRM!
• The 24V supply voltage for inputs I0-I35 is provided by the module. Buttons or sensors are used to switch it to ground (0V terminals). The voltage
may only be used for this application! The separate sensor connection (terminal 0 and 24) must be used for operating voltages of 24 V!
• The wiring connections for supplying power (230 V~ /50 Hz) to the motors (terminals L0-L3) must be protected with a 10 A automatic circuit breaker.
Make sure the loads are evenly distributed!

ConneCTIon PossIbILITIes

0 1
L0 O0 O1 O2 O3 O4 O5 L0 O6 O7 O8 O9 O10 O11 L1 L1
µ µ µ µ
M0 M1 M2 M3 M4 M5
µ µ µ µ µ µ µ µ
compact
L N
11
100-240 V ~
50-60 Hz
Status
12 x 1A
M
100-240V ~ / 50-60Hz
 Bus In  Bus Out
952 JRM
I0 I1 I2 I3 I4 I5 I6 I7 I8 0V I9 I10 I11 I12 I13 I14 I15 I16 I17 0V
10
10
connections
Three motors (M0-M2) can be connected to the output terminal block 0. Motors M0, M1, M2 can be connected
Terminal block 0 together, or M0 and M1 can be connected separately from M2 (e.g. for RCD protective switch). A phase leg
0
(Motor M0-M2) (e.g. L1) must be connected to the L0 terminals to supply the motors with power (230V~/50Hz).
caution! The L0 terminals require the same potential!
A total of 9 motors (M3-M11) can be connected to output terminal blocks 1-3 (3 motors to each terminal
Terminal block 1-3
1-3
block). One of the phase legs (L1-L3) must be connected to each terminal block to supply the motors with
(Motor M3-M11)
power (230 V~ /50 Hz).
4 Wind sensor / rain sensor 24V-input for Wind and/or rain sensor.
5 Sun sensor S1 24V-input for sun sensor S1.
6 Twilight sensor 24V-input for twilight sensor.
7 Automatic 24 V input for a switch to activate/deactivate auto mode.
24V inputs for connecting 3 dual buttons for the UP/DOWN function in group 0-2.
8
Pushbutton mode Group Attention! The "Sensors" setting deactivates Group 2! The inputs I30 and I31 for Group 2 are then available
for connection to a sun sensor S2/S3.
9 Pushbutton mode Central 24V-inputs for connection of 1 double button for the central UP/DOWN function
10 Pushbutton mode Local 24V-inputs for connection of 12 double buttons for the local UP/DOWN function
11 Main supply Operating voltage connection (100-240V~/50-60Hz).
12 Bus connection Bus port for data link between modules (see COMPACT BUS instructions).
13
Sensor connection Supply voltage for sensors (24V DC /100 mA).
PEHA_M_Installation_952JRM (Rev01-130308)
952 JRM
2 3
O12 O13 O14 O15 O16 O17 L2 L2 O18 O19 O20 O21 O22 O23 L3
M6 M7 M8 M9 M10 M11
µ µ µ µ µ µ µ µ µ µ µ µ
Compact
14:14 17.10.2012
12 13
24V

100mA 
PROG
0 24
36 x Input 24V
I18 I19 I20 I21 I22 I23 I24 I25 I26 0V I27 I28 I29 I30 I31 I32 I33 I34 I35
9 8
7 6 5 4
Description

ConneCTIon DIagRaM

terminal block 0
N
N'
FI
M0
L1'
F
L0 O0 O1
L3
µ M0 µ µ
9 mm
compact
12 x 1A
M
100-240V ~ / 50-60Hz
ENTER
952 JRM
I0 I1 I2 I3
0V
terminal
O0-O5
O6-O23
I35
I34
I33
I32
I26-I31
I24-I25
I0-I23
L, N
Bus In/Out
0, 24
terminal block 1
L1 L1
M1 M2 M3 M4 M5
F F
O3 O5 L0 O6 O7 O8 O9 O10 O11 L1 L1 O12
O2 O4
µ µ µ µ
M1 µ µ M2 µ M3 M4 µ M5 µ µ
L N
100-240 V ~
50-60 Hz
Status
 Bus In  Bus Out
36 x Input 24V
I4 I5 I6 I7 I8 0V I9 I10 I11 I12 I13 I14 I15 I16 I17 0V I18
terminal block 2 terminal block 3
Switches
Buttons or
Sensors
L2 L3
M6 M7 M8 M9
M10 M11
F F
O13 O14 O15 O16 O17 L2 O23 L3
L2 O18 O19 O20 O21 O22 L3
M6 µ µ M7 µ µ M8 µ µ M9 µ µ M10 µ µ M11 µ
Compact
14:14 17.10.2012
24V

100mA 
PROG ENTER
0 24
I19 I20 I21 I22 I23 I24 I25 I26 0V I27 I28 I29 I30 I31 I32 I33 I34 I35 0V
9 mm
GB - 1