Table of Contents
Advertisement
Quick Links
3450 Sabin Brown Road • Wickenburg, AZ 85390
(800) 992-3833 • mail@bnproducts.com
Rebar Cutter Instructions & Parts Lists
DC SERIES PORTABLE REBAR CUTTERS
CORDLESS MODELS
• DCC-1636BHL • DCC-2036BHL
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY
BEFORE ATTEMPTING TO USE YOUR TOOL
SERVICE NOTE
Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained. For a Service Repair
Center nearest you please call (800) 992-3833 or go visit us online:
www.bnproducts.com
Page | 1
September, 2020
Cordless_Cutter_Instructions_2020B
Advertisement
Table of Contents
Related Manuals for BN Products DC Series
Summary of Contents for BN Products DC Series
- Page 1 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • mail@bnproducts.com Rebar Cutter Instructions & Parts Lists DC SERIES PORTABLE REBAR CUTTERS CORDLESS MODELS • DCC-1636BHL • DCC-2036BHL IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO USE YOUR TOOL...
- Page 2 2 minutes. production tools. Contact your local distributor or BN Products When the oil is warm, run the piston out just before it re- turns and stop.
-
Page 3: Stopper Bolt Adjustment
Once set, the stopper needs no further adjustment while piston itself may be damaged. Return the unit to an authorized cutting rebar of the same diameter, but must be reset for a repair center or BN Products for repair. different size rebar. MAINTENANCE ON CUTTER BLOCKS... -
Page 4: Oil Level Check
blocks. If either cutting edge is dull or chipped, remove retain- CAUTION: Never remove oil-plug when unit is hot or ing bolts and rotate both blocks so that two new edges come oil will spurt out. into use. Replace and tighten bolts. (Each block has four cutting Check that oil is level with bottom of plug hole (i.e. -
Page 5: General Safety Rules
OVERHAUL on invites accidents. Remove any adjusting key or wrench before turning the power Return the unit to an authorized agent for overhaul at least tool on. A wrench or a key left attached to a rotating part of the once every two years, sooner if subjected to heavy use. - Page 6 Type DCC-1636BHL DCC-2036BHL Cutting ability #5, 5/8” (16mm) Grade 60 #6, 3/4” (20mm) Grade 60 or less or less Minimum cutting diameter .157” (4mm) Cutting Speed 2 seconds / 500 pieces per 4.2 seconds / 320 pieces per charge charge Power Source •...
-
Page 7: Charging Your Battery
USB device could be damaged. In any that the switch is turned off on the tool. Do not put your finger event, BN Products will not be responsible for any loss or fail- on the switch while attaching or removeing it. After installing ure of any connected equipment. -
Page 8: Charging Method
CHARGING LAMP DISPLAY Old batteries used for cordless tools are valuable and recyclable. It is a resource. When discarding batteries and similar prod- ucts, please cooperate with recycling centers. Please bring it to The charger has a “charging lamp” that displays the charging the store where you purchased it. - Page 9 LED WARNING SIGNALS Select charging method. Depending on the charging method, insert the storage battery into the charger or plug the power plug into an outlet. This product has a function to protect the tool and the storage Look for and turn on the USB power switch. When the battery, when the protection function is activated, while the USB power switch is turned on, the USB power lamp lights switch is pulled, the LED light will turn on.
- Page 10 DCC-1636BHL DCC-1636BHL 1C4273700 RAM RETURN SPRING 7GW004 WASHER M4 1C197301 DELIVERY VALVE 76303ZZ BEARING 1C2071000 HOUSING 1C1331 DELIVERY VALVE SPRING 1C3141000 CAM SHAFT 7USI26 USI PACKING 1C13352 SPRING GUIDE 7DP03015 DOWEL PIN 3X15 7B10030T11 STOPPER BOLT 10X30 1C13292 PUMP HEAD SEAL 7NT04030 TAPPING SCREW 4X30 1C16031...
- Page 11 DCC-2036BHL DCC-2036BHL 1C4273700 RAM RETURN SPRING 7GW004 WASHER M4 1C197301 DELIVERY VALVE 76303ZZ BEARING 1C2071000 HOUSING 1C1331 DELIVERY VALVE SPRING 1C3141000 CAM SHAFT 7USI26 USI PACKING 1C13352 SPRING GUIDE 7DP03015 DOWEL PIN 3X15 7B10030T11 STOPPER BOLT 10X30 1C13292 PUMP HEAD SEAL 7NT04030 TAPPING SCREW 4X30 1C16031...
- Page 12 BN PRODUCTS-USA,LLC. 3450 Sabin Brown Road • Wickenburg, Arizona 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com www.bnproducts.com Page | 12 September, 2020 Cordless_Cutter_Instructions_2020B...
Need help?
Do you have a question about the DC Series and is the answer not in the manual?
Questions and answers