Table of Contents
Advertisement
Quick Links
Please note: This tool is rated for #5 (16mm) Grade 60 Rebar Only. Do not try to bend
or cut material larger in size or rebar harder than grade 60 or you will cause tool damage
or machine failure.
DBC-16H_TM_16
BN PRODUCTS-USA, LLC.
3450 Sabin Brown Road • Wickenburg, AZ 85390
(800) 992-3833 • (928) 684-2813 • mail@bnproducts.com
DBC-16H
Portable Electric #5 (16mm) Combination
Rebar Bender and Rebar Cutter
Page | 1
Advertisement
Table of Contents
Related Manuals for BN Products DBC-16H
Summary of Contents for BN Products DBC-16H
- Page 1 BN PRODUCTS-USA, LLC. 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com DBC-16H Portable Electric #5 (16mm) Combination Rebar Bender and Rebar Cutter Please note: This tool is rated for #5 (16mm) Grade 60 Rebar Only. Do not try to bend or cut material larger in size or rebar harder than grade 60 or you will cause tool damage or machine failure.
-
Page 2: Table Of Contents
EXERCISE PROPER CONTROL PARTS DRAWING GUARD AGAINST ELECTRIC SHOCK PARTS LIST Ignorance of proper operating procedures can lead to accidents. If you have any questions about any procedures, contact the nearest authorized distributor/agent or call BN Products-USA. DBC-16H_TM_16 Page | 2... -
Page 3: General Safety Rules
BN PRODUCTS-USA, LLC. 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com GENERAL SAFETY RULES • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating WARNING: Read all instructions. -
Page 4: Basic Bending Instructions
Important: Always read, understand and obey the safety in- Important: Always read, understand and obey the safety in- structions included with your new DBC-16H #5 Combina- structions included with your new DBC-16H #5 Combina- tion Rebar Cutter and Bender before operating this tool or tion Rebar Cutter and Bender before operating this tool or any other power tool. -
Page 5: Bending/ Cutting
There is always a chance that the cut end may shoot out, especially if less than 30cm (1 foot) in length. REBAR IN-PLACE The DBC-16H can be used for bending rebar in-place, DESIGNATED MATERIALS protruding from a wall, floor or column. The closest Exceeding designated material specifications greatly in- bend to the surface would be a minimum of 4.5”... -
Page 6: Inspection
BN PRODUCTS-USA, LLC. 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com INSPECTION GENERAL OPERATING INSTRUCTIONS Inspect cutter before each application. Faulty or loose cutter blocks could result is personal injury. Keep handle CAUTION: Indicates hazard that could result in dry, clean and free from oil and/or grease. -
Page 7: Stopper Bolt Adjustment
BN PRODUCTS-USA, LLC. 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com STOPPER BOLT ADJUSTMENT 4. If a drop in power is observed and motor is unusually hot, check carbon-brushes. (See maintenance) THE STOPPER BOLT IS PROBABLY THE MOST 5. -
Page 8: Oil-Change
BN PRODUCTS-USA, LLC. 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com CAUTION: Hydraulic oil is highly flammable. Keep away packing. Turn cutter over and drain oil into a suitable recep- from sparks and naked flame. -
Page 9: Tool Specifications
BN PRODUCTS-USA, LLC. 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com TOOL SPECIFICATIONS DBC-16H DBC-16H Model No. Cutting Mode Bending Mode Cut / Bend 180 degree bend in 3 seconds Speed 7 seconds 2.42”... -
Page 10: Parts Drawing
BN PRODUCTS-USA, LLC. 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com DBC-16H_TM_16 Page | 10... -
Page 11: Parts List
BN PRODUCTS-USA, LLC. 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • (928) 684-2813 • mail@bnproducts.com DBC-16H_TM_16 Page | 11... - Page 12 DBC-16H_TM_16 Page | 12...
Need help?
Do you have a question about the DBC-16H and is the answer not in the manual?
Questions and answers