Download
Share
Print this page
Texecom Flashguard Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Texecom Manuals
  4. Marine Equipment
  5. Flashguard
  6. Installation instructions manual
Texecom Flashguard Installation Instructions Manual

Texecom Flashguard Installation Instructions Manual

Hide thumbs

Advertisement

Available languages

Available languages

Quick Links

Download this manual
Texecom Ltd
St Crispin Way
GB
Haslingden
Lancashire
BB4 4PW
Technical Helpline:
Sales Hotline:
Fax:
01706 223450
Email:
Project Advanced Security Systems, S.A.
Avda. Doctor Severo Ochoa Nº 35,
E
Edificio 5,
Local A 28100 Alcobendas
(MADRID)
Tlfno:
Fax:
91 754 36 50
Email:
All information on this sheet is believed to be correct at the time of going to press.
Texecom can accept no responsibility for damage caused by incorrect installation.
08456 300 600
01706 220460
Sales@texe.com
91 304 56 43
att.cliente@pass-project.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the Flashguard and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Texecom Flashguard

Summary of Contents for Texecom Flashguard

  • Page 1 Tlfno: 91 304 56 43 Fax: 91 754 36 50 Email: att.cliente@pass-project.com All information on this sheet is believed to be correct at the time of going to press. Texecom can accept no responsibility for damage caused by incorrect installation.
  • Page 2 Premier Alarm Sounder Backplates Flashguard - The Installer’s Choice 1 - 5 6 - 10 Installation Instrucciones de Instructions Instalación...
  • Page 3 I I n n s s t t a a l l l l a a t t i i o o n n I I n n s s t t r r u u c c t t i i o o n n s s Thank you for buying Flashguard, the generic term for sounder/strobe units.
  • Page 4 1 Mounting and Assembly Instructions Using the backplate of the unit (or the template on the rear of the carton) mark the positions of the three mounting screw holes (A), and cable entry hole (B). Drill and plug the screw holes as marked. Using a long masonry drill bit, drill a hole through the wall for the cable.

  • Page 5: Typical Wiring Configurations

    3 Terminal Connections (J) For use with positively triggered panels only. Do not connect to Supply + STROBE TRIG + (+12V Hold Off) when using a standard negatively triggered panel. TRIGGER + Applying a negative voltage triggers the sounder. TRIGGER - Applying a negative voltage triggers the strobe.
  • Page 6 5 Precautions G Two units in series Note: In this configuration the total current consumption approaches 1 amp. Ensure that the alarm panel can source this amount of current. If in doubt change the mode of operation of one or both units to SCB to reduce the current load on the panel. G Tamper switches (C) Care should be taken to ensure that none of the wiring prevents the tamper switch from moving freely.

  • Page 7: Technical Specification

    Technical Specification Sounder Maximum Sounder Output (dBA @ 1m) Strobe Frequency (Hz) Input Voltage - Maximum - Minimum Current Consumption (mA) @ 13.2V - Sounder (SAB mode) - Sounder (SCB mode) - Strobe - Standby Current - Maximum battery charge current (constant current charger) Technical Helpline &...
  • Page 8 I I n n s s t t r r u u c c c c i i o o n n e e s s d d e e I I n n s s t t a a l l a a c c i i ó ó n n Gracias por comprar Flashguard, el término genérico para aparatos de sonido/luz.
  • Page 9 1 Instrucciones de Montaje: Usando la placa trasera del aparato (o el molde detrás del cartón) marque las posiciones de los tres agujeros de montaje (A), y el agujero para cable (B). Taladre y prepare los agujeros marcados. Usando un taladro largo, haga un agujero a través de la pared para el cable. Pase el cable a través del seguro en el agujero para cable (B) y descubra el cable usando la guía en la placa trasera.
  • Page 10 3 Terminal de Conexiones (J) Para uso con centrales que tienen salidas positivo. No lo conecte STROBE TRIG + a la red + (+12V Hold Off) si usa una central con salidas negativo. TRIGGER + La sirena empieza al aplicarse aquí un voltaje negativo. TRIGGER - STROBE TRIG - El flash empieza al aplicarse aquí...
  • Page 11 5 Precauciones G Dos sirenas en serie: Nota: De esta manera el consumo total de corriente se acerca a 1 Amperio. Asegurase de que el Panel de Control puede suplir esta corriente. Si no esta seguro, cambie el modo de operación de una o ambas unidades a SCB para reducir la carga al panel. G Interruptor sabotaje(C): Tenga cuidado de asegurar que ningún cable prevenga el libre movimiento del interruptor sabotaje.
  • Page 12 Especificacion Tecnica Potencia Maxima De Sonido (dBA @ 1m) Frequencia De Flash (Hz) OLTAGE AXIMO - Maximo - Minimo Consumo de Corriente (mA) @ 13.2V - Sirena (Modo SAB) - Sirena (Modo SCB) - Flash - Corriente En Reposo...