1. Manuals
  2. Brands
  3. elsner elektronik Manuals
  4. Temperature Controller
  5. KNX T-AP
  6. Installation and adjustment

elsner elektronik KNX T-AP Installation And Adjustment

Hide thumbs Also See for KNX T-AP:
Table of Contents

Advertisement

Quick Links

Download this manual
EN
KNX T-AP
Temperature Sensor
Item number 70121
Installation and Adjustment

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KNX T-AP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for elsner elektronik KNX T-AP

Summary of Contents for elsner elektronik KNX T-AP

  • Page 1 KNX T-AP Temperature Sensor Item number 70121 Installation and Adjustment...

  • Page 3: Table Of Contents

    6.6.3. OR logic connection inputs ................ 23 Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany Temperature Sensor KNX T-AP • from software version 0.2.0, ETS programme version 2.0 Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 4 Clarification of signs Installation, inspection, commissioning and troubleshooting of the device must only be carried out by a competent electrician. This manual is amended periodically and will be brought into line with new software releases. The change status (software version and date) can be found in the contents footer. If you have a device with a later software version, please check www.elsner-elektronik.de in the menu area "Service"...

  • Page 5: Description

    5.5 mA, max. 15 mA when programming LED is active Data output KNX +/- bus terminal plug BCU type Own micro controller PEI type Group addresses max. 184 Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 6: Installation And Commissioning

    Elsner Elektronik is not liable for any changes in norms and standards which may occur after publication of these operating instructions.

  • Page 7: Location

    Fig. 2 Rear view with dimensioning of Slot for KNX terminal +/- openings for mounting Programming button for teaching the instrument Programming LED Cable entry with threaded joint Temperature sensor tip Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 8: Connection Of The Sensor

    ATTENTION The device can be damaged if significant volumes of water penetrate the housing. • Do not clean with high pressure cleaners or steam jets. Temperature Sensor KNX T-AP • Status: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 9: Transfer Protocol

    Temp. threshold value 4: (1:+ | 0:-) Input 1,006 Temp. threshold value 4: Switching output Output 1,001 C R T Temp. threshold value 4: Switching output Input 1,006 block Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 10 C R T 0=OFF) Temp. controller: Cooling 2 status (1=ON | Output 1,001 C R T 0=OFF) Temp. controller: Window status Input 1,019 (0: CLOSED | 1: OPEN) Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 11 OR logic 4: 8-bit output A Output 5,010 C R T OR logic 4: 8-bit output B Output 5,010 C R T Software version Output 217,001 C R T Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 12: Setting Parameters

    • 20 messages per second Use malfunction object No • Yes 6.3. Temperature measured value Use Offsets to adjust the readings to be sent. Offset in 0.1°C -50…50; 0 Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 13: Temperature Threshold Values

    Beforehand, enter how the threshold value will be received from the bus. Basically, a new value can be received, or simply a command to increase or decrease. Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 14 No • Yes Analysis of the blocking object • At value 1: block | At value 0: release • At value 0: block | At value 1: release Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 15: Temperature Pi Control

    Behaviour of the blocking object with value • 1 = Blocking regulation | 0 = Releasing regulation • 0 = Blocking regulation | 1 = Releasing regulation Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 16 If the setpoint is set via parameters: Set the setpoint for heating and/or cooling. Specified setpoint using Parameter Setpoint (heating) in 0.1°C -300 … 800 Setpoint (cooling) in 0.1°C -300 … 800 Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 17: Heating Control Level 1/2

    Setpoint difference between 1st and 2nd 0...100; 40 level (in 0.1°C) (for level 2) Control type • 2-point-control (for level 2, no common control variables) • PI control Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 18 • Electric heating Maximum control variable is reached Warm water heating: 5 at setpoint/actual difference of (in °C) Floor heating: 5 Convection unit: 4 Electric heating: 4 Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 19: Cooling Control Level 1/2

    In the 1st level, cooling is controlled by a PI control in which either control parameters can be entered or predetermined applications can be selected. Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 20 This setting provides fixed parameters for a cooling ceiling Control type • PI control Setting of the controller by • Controller parameter • specified applications Application • Cooling ceiling Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 21 Decide when night reduction is to be activated. Night reduction for object value • 1 = active | 0 = inactive • 0 = active | 1 = inactive Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 22 • Increase / Decrease Interval 0.1°C • 0.2°C • 0.3°C • 0.4°C • 0.5°C • 1°C • (only when "increasing/decreasing") 2°C • 3°C • 4°C • 5°C Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 23: Logic

    The same setting options are available for AND and OR logic. Each logic output may transmit one 1-bit or two 8-bit objects. Determine what the out put should send if logic = 1 and = 0. Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 24: And Logic Connection Inputs

    Communication object logic input 2 inverted Communication object logic input 3 Communication object logic input 3 inverted Communication object logic input 4 Communication object logic input 4 inverted Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.

  • Page 25: Or Logic Connection Inputs

    AND logic output 2 AND logic output 2 inverted AND logic output 3 AND logic output 3 inverted AND logic output 4 AND logic output 4 inverted Temperature Sensor KNX T-AP • Version: 27.01.2020 • Errors excepted. Subject to technical changes.
  • Page 26 Elsner Elektronik GmbH Control and Automation Engineering Sohlengrund 16 75395 Ostelsheim Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de Germany +49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de Technical support: +49 (0) 70 33 / 30 945-250...

This manual is also suitable for:

70121

Table of Contents