Stereo Aux Return Control; Supplement To Ub1832Fx-Pro - Behringer EURORACK UB1622FX-PRO User Manual

EURORACK UB1622FX
Fig. 2.11: Monitor fader of the UB1832FX-PRO
Press the MUTE switch to mute the monitor send.
The SOLO switch routes the monitor send to the solo bus
(post-fader and post-mute) or to the PFL bus (pre-fader and
pre-mute). The position of the MODE switch in the main section
determines which of the buses is selected.
The STEREO AUX RETURN 1 control determines the level of
this signal in the main mix. If STEREO AUX RETURN 1 is used as
effects return, this will determine the level of the effects when
mixed with any “dry” channel signal.
+
Fig. 2.12: Stereo aux return and
stereo aux return (to aux send) controls
The two right-hand STEREO AUX RETURN controls have a
special function: they can be used to add an effect to a monitor
mix. An example follows (UB1622FX-PRO wired to an effects
device):
In this instance, your effects device should be set up as follows:
the AUX SEND 2 jack should be connected to the L/Mono input of
your effects device, with its outputs coming back into the STEREO
AUX RETURN 1 jacks.
Connect the AUX SEND 1 jack output to the amplifier of your
monitor system. The AUX SEND 1 master control determines the
overall volume of the monitor mix.
/UB1832FX
-PRO
Using the STEREO AUX RETURN (TO AUX SEND) control, the
effect signal can now be blended into the monitor mix.
You can easily use the headphones distribution amplifier
BEHRINGER POWERPLAY PRO HA4700/HA8000 to provide four
(HA8000: eight) stereo headphone mixes for your studio.
The following table shows which jacks on the console can be
used for this purpose.
Tab. 2.1: Connectors and controls for monitor mix with effect
On consoles UB1622FX-PRO and UB1832FX-PRO this is the
STEREO AUX RETURN 2, on consoles UB2222FX-PRO and
UB2442FX-PRO this is the STEREO AUX RETURN 3.
Use the STEREO AUX RETURN FX control to determine the
level of the signal routed from the AUX RETURN FX jacks to the
main mix. If nothing is connected to these jacks, the output of the
built-in effects module will appear.
This switch routes the signal fed in via the STEREO AUX
RETURN FX jacks either to the main mix (not pressed) or to the
submix (pressed).
On the UB2442FX-PRO you can select which subgroup the
signal is assigned to (switches 1-2 / 3-4, to the right of MAIN MIX /
TO SUBS).
Additionally, this model allows you to route the aux returns
together to the solo bus and the PFL bus. The LED lights up when
Solo is on.
This control behaves the same way as the other stereo aux
returns. Additionally, it provides for a simple monitor path using
the switch CTRL ROOM & PHONES ONLY.
Use this switch to route the signal appearing at the AUX
RETURN 4 jacks to the control room and headphones outputs.
The UB1832FX-PRO has a stereo fader for the AUX RETURN
FX and offers a variety of routing options: MUTE disables the
effect return (but not PFL of course!), SOLO routes it to the Solo
or PFL busses, SUB to the subgroups and MAIN to the main mix.
2. CONTROL ELEMENTS AND CONNECTORS
/UB2222FX
-PRO -PRO
‘‡r…hyÃrssrp‡†Ã ‘‡r…hyÃrssrp‡†Ã
qr‰vprÃ…rprv‰r†Ã qr‰vprÃ…‚ˆ‡r†Ã†vthyÃ
†vthyÃs…‚€ ihpxÇ‚
à 
V7 %!!AYQSP
STEREO AUX
!
AUX SEND RETURN
connectors
V7 '"!AYQSP
STEREO AUX
!Ã
AUX SEND RETURN
connectors
V7!!!!AYQSP
STEREO AUX
Ã!
AUX SEND RETURN connectors
Â…Ã!
V7!##!AYQSP
STEREO AUX
!
AUX SEND RETURN
connectors
‚ƒ‡v‚hy)
STEREO AUX
à !Ã
AUX SEND RETURN
connectors
/UB2442FX
-PRO
UurÃrssrp‡Ã†vthyÃ
…rhpur†Ã‡urÀ‚v‡‚…Ã
€v‘Évh
«
STEREO AUX
Ã
RETURN (TO AUX
SEND ) control
MONITOR switch of
Ã!
the FX/AUX RET
STEREO AUX
Ã
RETURN (TO AUX
SEND ) control
STEREO AUX
Ã
RETURN (TO AUX
SEND ) control
STEREO AUX
!
RETURN (TO AUX
!
SEND ) control
9