Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for JED T464
-
Page 1: T464 Installation And Setup
JED MICROPROCESSORS PTY LTD 173 Boronia Rd, Boronia, (PO Box 30), Victoria, 3155, Australia. Phone: +61 3 9762 3588, Fax: +61 3 9762 5499. www.jedmicro.com.au jed@jedmicro.com.au T464 Installation and Setup 20090709 v1r0 JED Microprocessors Pty. Ltd. - Page 1 of 27... -
Page 2: Table Of Contents
T464 Status LED’s..................21 Network Connectivity Tests ..............21 Viewing IP Configuration of the PC using IPCONFIG ......22 Testing Connectivity Using PING............24 T464 Specifications ..................26 Power supply ..................26 Relays.....................26 Revision History ..................27 20090709 v1r0 JED Microprocessors Pty. Ltd. - Page 2 of 27... -
Page 3: Disclaimer
This document: • Assumes the reader has prior experience with network configuration and troubleshooting. • Provides information necessary to install and setup a T464 on a network. • Contains specific information about networks running on Microsoft Windows XP and Microsoft Windows Vista operating systems (Windows). -
Page 4: Installation Scenarios
(MAC) in order to allocate an IPv4 address (IP) to the T464. Each T464 has a unique MAC. The MAC is printed on a label near the Ethernet connector. The MAC is also reported by the setup software accessed via a serial terminal. -
Page 5: Dhcp
10001. Some network security software may block access to this port and it may be necessary to alter port usage permissions. Installations where the T464 and the administration terminal are on the same subnet may make use of auto discovery. Auto discovery relies on issuing a broadcast command via UDP on port 30718 and capturing the IP of each T464 that responds. -
Page 6: T464 Configuration
• T460/T464 Software Upload Cable. • Appropriate DC power source for T460/T464. A serial terminal is required to configure T464. Usually, a PC or notebook running serial terminal application software is employed. There are a number of serial terminal applications that may be downloaded from the internet at no cost. -
Page 7: Accessing The Setup Menu
ESC: Exit via Software Restart Enter Function - [h(elp) - a|i|j|k|l|v|ESC]: Monitor Text Note: The Setup Menu will exit via a restart and the T464 will resume normal operation if: • The user hits the ESC key, or • No user input is detected for longer than sixty seconds. -
Page 8: Network Parameters
T464 Installation and Setup Network Parameters The T464 leaves JED configured with DHCP, BOOTP and AutoIP enabled. This configuration will operate in the default Windows network environment which uses AutoIP. A DHCP server will also configure the network parameters without any further intervention. - Page 9 [The following example shows parameters set by a DHCP Server] 192.168.000.003 Gateway: 192.168.000.254 Mask: 255.255.255.000 Name Server: 203.012.160.035 Manually configure IP, Subnet Mask and Gateway? y/n: The Network parameters display: T464 configured via DHCP 20090709 v1r0 JED Microprocessors Pty. Ltd. - Page 9 of 27...
-
Page 10: Special Ip Addresses
T464 Installation and Setup Special IP Addresses There are some special IP addresses that may be used with the T464 to specifically control the BOOTP, DHCP, and AutoIP options. These addresses are shown in Table 1. ü Enabled û Disabled... -
Page 11: Gateway
Gateway The gateway parameter is an IP address that provides routing information to the T464. The T464 default settings will allow a DHCP server to configure this information. This gateway IP may be entered manually and is necessary if the administration terminal resides on a different subnet to the T464. -
Page 12: Reset Network Interface To Factory Defaults
T464 Installation and Setup Reset Network Interface to Factory Defaults The T464 network configuration may be reset to factory defaults by hitting ‘y’ when prompted. Following successful restoration of network default settings, the T464 will exit via a restart and resume normal operation. -
Page 13: Show Input State
T464 Installation and Setup Show Input State Some versions of the T464 are equipped with 4 relay outputs and 4 switch closure to ground inputs. The state of the T464 I/O<hyperlink to spec.> may be observed be selecting the ‘Show Input State’ option from the Setup Menu. -
Page 14: Change User Level
This option is reserved for JED Technical support use. Input Special Notes The T464 can store up to 80 characters of notes to be displayed on the administration terminal. This field may provide comments regarding room configuration and attached devices, contact extensions and phone numbers, etc. -
Page 15: Input Location
T464 Installation and Setup Input Location The T464 can store up to 80 characters of location information to be displayed on the administration terminal. This field may provide comments such as room level, building, campus, etc. The Location text may be edited by selecting option ‘l’... -
Page 16: Load Semi-Static Data From T460
45 seconds after power is applied. The current copy of T460 information stored in the T464 may be displayed by selecting the Setup Menu option ‘v’. The following panel illustrates output after selecting option ‘v’:... - Page 17 When the user chooses to update the Semi-static values, the progress is displayed. For each T460 value successfully loaded into the T464, a ‘+’ is displayed. If any value fails to load, a ‘X’ is displayed, and the T464 default value is used instead.
-
Page 18: T464 Software Upload
• 464v2ee_swv1r4_200902261128.hex The most recent Software will have the latest Date and Time stamp. Note: Both files are required to upgrade the Software in the T464. Only files having the same version and release numbers should be used. Uploader Application Software... -
Page 19: Procedure
T464 Installation and Setup Procedure 1. Do Not apply power to the T460 yet. 2. Connect the T464 Projector 0 port to the PC/Notebook serial port using a T460/T464 Software Upload cable. 3. Open the Megaload application. The MegaLoad Application 5. - Page 20 40 and 50 seconds to complete. If the upload process does not start, click the “Send Reset” button in the Command panel. 14. The successful programming of the T464 Flash and EEPROM may be verified by sliding the scroll bar in the Message panel.
-
Page 21: Windows Network Configuration
T464 Installation and Setup Windows Network Configuration T464 Status LED’s In the corners of the T464 Ethernet socket are two status LED’s. The colour and state of the LED’s are helpful in determining network connectivity. The LED’s may be interpreted using Table 4. -
Page 22: Viewing Ip Configuration Of The Pc Using Ipconfig
DNS Servers ... : 192.168.0.254 NetBIOS over Tcpip..: Enabled [Other adapters may appear below…] The highlighted text shows the current configuration of the Network Adapter. 20090709 v1r0 JED Microprocessors Pty. Ltd. - Page 22 of 27... - Page 23 • The Subnet mask on the PC and the T464 should be the same. • The IP of the PC and the T464 should NOT be the same. • The IP of the T464 should be selected from a range within the same subnet as the PC.
-
Page 24: Testing Connectivity Using Ping
PC with XP or Vista networking enabled. Ping sends a packet of data on TCP port 7. The T464 will ‘echo’ the packet back to the PC and the time taken for the round trip will be displayed, if the T464 is located. - Page 25 Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.1.3: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), Successful and unsuccessful PING results output. 20090709 v1r0 JED Microprocessors Pty. Ltd. - Page 25 of 27...
-
Page 26: T464 Specifications
T464 Specifications Power supply The T464 requires a power source rated to supply: • 12VDC @ 170mA If the T460 is to be powered from the T464, the power source must be rated to supply: • 12VDC @ 270mA Relays... -
Page 27: Revision History
T464 Installation and Setup Revision History 20090202 v1r0 Mik Biber – JED Microprocessors Pty. Ltd. Preliminary release. 20090327 Highlight requirement for T460 FLAG ‘E’ to be set. 20090709 Remove reference to Preliminary. 20090709 v1r0 JED Microprocessors Pty. Ltd. - Page 27 of 27...