Page 1
Ventilation Wired Remote Controller Owner's & Installation Manual Models: PZRCUSB0 IMPORTANT • Please read this installation manual completely before installing the product. • Installation work must be performed in accordance with the national wiring standards by authorized personnel only. • Please retain this installation manual for future...
Safety Precaution Safety Precaution • The installation requires expert skills, and it should be installed by the service center or other shops specialized in the installation and recognized by our company. • For all the problems arising after installation by someone who has no relevant qualifications, our company will not provide free service.
Page 4
Safety Precaution Request to the service center or installation Do not give the shock using sharp and specialty store when the product becomes wet. pointed objects. • It will cause fire or electric shock. • It will cause breakdown by damaging parts. AU TO SW IN OP ER...
Part Description Part Description Name and Function of Remote Controller 1. Display Window 2. Execute/Cancel of Time EXTERNAL VENTILATOR OPERATION SUB FUNCTION Reservation, Weekly Heater Preheat Linked Run Auto Auto Dual Remote Defrost Humidify Reservation/Week Day Central Run Heat XCH Auto Normal Fan Speed Z O N E...
Installation Instruction Installation Instruction Remove the sticker attached on the back of the insulation and attach it on the wall where you want to install remote controller. Separate the cover of remote control as shown on the right hand side. Fix the setup board over the insulation.
Remote controller Connection Method Remote controller Connection Method 1. Check if the cable is properly conneced to CN-REMO port (CN-AIRCON is used if remote controller is connected with Airconditioner ) P/N:3850A25162L CN-REMO CN-AIRCON CN-REMO CN-AIRCON 2. Connect the cables between the indoor unit and the remote controller. Connector for the Connector for the remote controller side...
Connection Method Between Ventilation Remote Controller and Air conditioner Remote Controller Connection Method Between Ventilation Remote Connection method between ventilation Controller and Air conditioner Remote Controller Ventilaton remote controller can be installed along with air conditioner remote controller. But connect ventilation wired remote controller and air conditioner wired remote controller only when its necessary.
Page 9
Connection Method Between Ventilation Remote Controller and Air conditioner Remote Controller 5. Use the Terminal block to connect the ventilation remote controller and the air conditioner remote controller (Yellow wire : Communication line, Black wire : Ground) AUTO SWING OPERATION SET TEMP FAN SPEED SUB FUNCTION...
Address Setup for Central Control Address Setup for Central Control You can set the address by pressing the Program button and the Set/Clr button for about 3 seconds at EXTERNAL VENTILATOR OPERATION SUB FUNCTION Linked Run Heater Preheat Auto Auto the same time.
Address Setup for Airconditoner -Ventilator Connection Address Setup for Airconditoner -Ventilator Connection Set the air conditioner remote control to set the central control address of each indoor unit. EXTERNAL VENTILATOR OPERATION SUB FUNCTION Linked Run Heater Preheat Auto Auto Dual Remote Defrost Humidify Central Run Heat XCH Auto Normal...
Page 12
Address Setup for Airconditoner -Ventilator Connection Press the Timer and Min button simultaneously EXTERNAL VENTILATOR OPERATION SUB FUNCTION about 3 seconds.Now the remote controller enters Heater Preheat Linked Run Auto Auto Defrost Humidify Dual Remote the mode to input an end address of the connected Central Run Heat XCH Auto Normal Fan Speed...
E.S.P(Influx) E.S.P(INFLUX) What is an E.S.P function? This is the function that decides the strength of the air for each air speed and because this function is to make the installation easier, please do not use this function while using the remote controller. If you press the Timer button and the Fan speed button EXTERNAL VENTILATOR OPERATION...
E.S.P(Outflow) E.S.P (OUTFLOW) What is an E.S.P function? This is the function that decides the strength of the air for each air speeds and because this function is to make the installation easier, please do not use this function when using the remote controller. If you press the Timer button and the Ventilaton mode EXTERNAL VENTILATOR OPERATION...
Ventilation Mode Setting Ventilation Mode Setting Select the desired operation mode by EXTERNAL VENTILATOR OPERATION SUB FUNCTION pressing the Ventilation Mode button. Linked Run Heater Preheat Auto Auto Auto Defrost Humidify Dual Remote • You can select the Operation Mode in Central Run Heat XCH Auto Normal...
Rapid Ventilation/Power Saving Ventilation Rapid Ventilation/Power Saving Ventilation Rapid Ventilation EXTERNAL VENTILATOR OPERATION SUB FUNCTION Press the [Rapid Ventilation] button. Linked Run Heater Preheat Auto Dual Remote Defrost Humidify fresh Central Run Heat XCH Auto Normal Fan Speed Z O N E •...
Additional Function Additional Function Setting of current time • You can easily set the current time. Press the [Hour] button on the adjustment part of the remote controller. EXTERNAL VENTILATOR OPERATION SUB FUNCTION Linked Run Heater Preheat Auto Auto Dual Remote Defrost Humidify Figures change from 00 to 23 whenever you press Central Run Heat XCH Auto...
Weekly Reservation Setup Weekly Reservation Setup No reservation operation can be set if the current time not is not set. Example) To operate the ventilator at 06:00 ~ 08:00 and 13:00 ~ 22:00 on Monday Press the [Program] button on the adjustment part EXTERNAL VENTILATOR OPERATION SUB FUNCTION...
Holiday Setup Holiday Setup Example) In the case it's holiday on Tuesday. • Automatically turns off when the reservation day set up. Press the [Program] button on the adjustment part of the remote controller. • Display part flickers as following figure. EXTERNAL VENTILATOR OPERATION SUB FUNCTION...
On/Off Reservation On/Off Reservation ‘On’ Reservation • This function will automatically turn ON the units at set time. Timer Press [Timer] button on the adjustment part of the remote controller. Timer Timer Set the desired time with [Hour, Min] button. Timer Cancel fresh...
Optional Function Optional Function Plasma Press the plasma button. EXTERNAL VENTILATOR OPERATION SUB FUNCTION Linked Run Heater Preheat Auto Auto Dual Remote Defrost Humidify Central Run Heat XCH Auto Normal Fan Speed The plasma function is performed so that purifies Z O N E 1 2 3 4 PLASMA...
Optional Function Humidifier You can use the humidifier function. Press the Humidifier button. When indoor air condition is dry, the humidifier operates and it maintains the EXTERNAL VENTILATOR OPERATION SUB FUNCTION Linked Run Heater Preheat Auto Auto humidity The humidification function operates when the Dual Remote Defrost Humidify Central Run Heat XCH Auto...
Page 23
P/No.: 3828A20860F Printed in Korea After reading this manual, keep it in a place easily accessible to the user for future reference.