Page 1
Visit us at : http://www.lgservice.com Deluxe Wired Remote Controller For Split Duct Owner's & Installation Manual Models: PDRCUDB0 PDRCUDB0B PDRCUDB0S IMPORTANT • Please read this manual completely before installing the product. • Installation work must be performed in accordance with the national wiring standards by authorized personnel only.
Deluxe wired remote controller Owner’s & Installation Manual TABLE OF CONTENTS I Safety precautions ............3~4 I Part description ..............5~6 • Deluxe wired remote controller.............6 I Deluxe wired remote controller switch information ...7 I Installation method ...............8 I Group control.................9 I Installation instruction..........10~12 •...
Safety Precautions Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. I Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. WARNING This symbol indicates the possibility of death or serious injury.
Page 4
Safety Precautions Request to the service center or installation Do not give the shock using sharp and specialty store when the product becomes wet. pointed objects. • It will cause fire or electric shock. • It will cause breakdown by damaging parts. CAUTION I In-use Do not clean using the...
Part Description Part Description 1. Wired remote controller 2. LCD screen 3. Connecting cable and connector AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 Accessory Connecting cable Fixing screw (2EA) Owner / Installation Installation paper...
Deluxe wired remote controller switch information Deluxe wired remote controller switch information Product selection 1. C/O Product 2. H/P Product • On installing, don't impact to the PCB and LCD display • Don't remove the caution label. Zone type selection •...
Installation Method Installation Method Put the installation paper on the place and determine the position and height of the fixing screws of the deluxe wired remote controller. • Refer to the printed side of the installation paper. The position of the fixing screws Plug the connecting cable into the indoor unit.
Installation Method Group Control 1. When installing more than 2 units of air conditioner to one deluxe wired remote controller, please connect as the right figure. • If it is not event communication Signal wire indoor unit, set the unit as slave. •...
Installation Instruction Installation Instruction Installer Setting - Test Run Mode The Test Run Mode is to check the installation status of the product. The temperature will not be controlled during trial operation. Instead the product will operate in several modes such as cooling, strong wind, comp-on. The test run mode is to check the installation status of the product.
Installation Instruction Installer Setting - Setting the Cental Control Address Group No. Indoor No. Press the button. Press the button. Press the button to change the group number. Press the button to AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 change the indoor unit number.
Installation Instruction Installer Setting - ESP Function E.S.P function is setting the volume of each air flow. It is for the convenience of installation. It is recommended that you should not use this function while using the wireless remote controller. CAUTION If you set ESP incorrectly, the air conditioner may malfunction.
Owner's Instruction Owner's Instruction Cooling Mode Cooling mode will begin if you press the button. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 Press the button and set the expected temperature lower than the current room temperature. REMO (18~30°C) ZONE 1...
Owner's Instruction Heating Mode Press the button and then press the button. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 Set the expected room temperature higher than the current room temperature. (16~30°C) REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 A click of the button will increase the expected...
Owner's Instruction Auto Changeover Mode AUTO Press the button and then press the button. AUTO AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 When the expected temperature is lower than the room temperature : Cooling Mode. When the expected temperature is higher than the REMO ZONE 1 ZONE 2...
Owner's Instruction Dehumidification Mode Dehumidification operation: Dehumidification by lowering temperature slightly Press the button on the remote controller. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 Select the dehumidification function by pressing the button and the button. REMO ZONE 1 ZONE 2...
Owner's Instruction Fan Mode Press the button on the remote controller. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 Select the fan function by pressing the button button. REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 When the fan is being done, "Fn"...
Owner's Instruction Fan Speed Selection You can easily control the fan speed. Select the proper fan speed which you want by pressing the button on the remote controller. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 • If you press the button, the strength of the fan speed will change in the order of Low ¡...
Sub Function Sub Function Thermistor Press the button on the remote controller. INDOOR REMO Set thermistor mode by pressing button. Function Selected button Operation in indoor unti temperature INDOOR sensor. Operation in remote controller REMO temperature sensor. Operation in lower temperature after comparing the temperature between the indoor unit and remote controller.
Sub Function Plasma You can use the plasma function. Press the button. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 Press button. REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 • A click of the button will turn on/off the indicator. •...
Special Function Special Function This is a function to prevent tampering of settings by children or others. Child Lock You can use the child lock function. Press the button of the remote controller. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 Press...
Special Function Zone control function You can control zones when you've installed the zone controller new type. Press button. ZONE 2 ZONE 3 ZONE 1 ZONE 4 ZONE 1 ZONE 2 ZONE 3 ZONE 4 AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4...
Special Function Simple Reservation Press button on the remote controller. Press easy button. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 REMO You can change the values by pressing the ZONE 1 ZONE 2 ZONE 3 ZONE 4 control buttons.
Special Function Setting the current time You can set the current time by pressing the time display. When the time display is selected, a window for date and time setting shows up. AUTO INDOOR REMO ZONE 1 ZONE 2 ZONE 3 ZONE 4 REMO ZONE 1...
Special Function Weekday reservation Weekday reservation is the function to set the time to turn on and off for each day during the week from monday through sunday. Press the button on the control panel of the remote controller. Select the day of week to set using the button.
Special Function Different Mode Operation When one outdoor unit have several indoor units, different mode operation is which each indoor unit operate different mode. If one indoor unit operate heating Mode while several indoor units are operating cooling mode, segment and segment are blinking like screen on the left •...
Page 27
P/No.: 3828A20561Y Printed in Korea After reading this manual, keep it in a place easily accessible to the user for future reference.