Related Manuals for Häfele Connect Mesh
Summary of Contents for Häfele Connect Mesh
- Page 1 Connect Mesh 6-way Distributor Version 1.0 © 2020 by Häfele GmbH & Co KG 1/10 Subject to Adolf-Häfele-Str. 1 · D-72202 Nagold www.hafele.com alteration...
-
Page 2: Change History
1. Change history Version Date Changes • Initial Documentation 2/10 © 2020 by Häfele GmbH & Co KG Subject to Adolf-Häfele-Str. 1 · D-72202 Nagold www.hafele.com alteration... -
Page 3: Table Of Contents
2. Table of Contents 1. Change history _________________________________________________________________________________________________________2 2. Table of Contents _______________________________________________________________________________________________________3 3. Connect Mesh 6-way Distributor ________________________________________________________________________________________4 3.1. General information _____________________________________________________________________________________________________4 3.2. Power Supply __________________________________________________________________________________________________________4 3.3. Ports _________________________________________________________________________________________________________________4 3.4. Sensor Port ___________________________________________________________________________________________________________4 Supported Sensor Models ___________________________________________________________________________________________________5 LED IR Dimmer Switch __________________________________________________________________________________________________5... -
Page 4: Connect Mesh 6-Way Distributor
Reset Button Status LED Mounting holes Sensor Port [image 3.1.1] The Connect Mesh 6 way distributor acts as a node in your BLE Mesh network and manages connected devices such as LED products and electrical furniture fittings. 3.2. Power Supply Connect the device to the power supply by plugging it into a Häfele Loox LED Driver. Please note the specified maximum allowed power values of the Driver and the Connect Mesh 6 way distributor. This information influences the maximum performance of the connected devices. -
Page 5: Supported Sensor Models
Supported Sensor Models LED IR Dimmer Switch Product number: 833.89.126 You can toggle devices on and off or dim lights by holding. IR-Sensor Switch On/Off Product number: 833.89.127 You can toggle devices on and off. Door Sensor Switch Product number: 833.89.128 If the sensor is covered, the signal turns off otherwise on. Motion Detector Product number: 833.89.135 The signal turns on for 30 seconds if motion is detected and then turns off again. -
Page 6: Ir Sensor Switch
IR Sensor Switch Product number: 833.89.136 You can toggle devices on and off by approaching the IR-sensor on the side. IR Sensor Switch Modular Product number: 833.89.137 You can toggle devices on and off by approaching the IR-sensor on the side. IR-Dimmer Modular Product number: 833.89.129 You can toggle devices on and off or dim lights by approaching the IR-sensor on the side and or holding. Capacitive Switch Product number: 833.89.087 You can toggle devices on and off by... -
Page 7: Capacitive Dimmable Switch
Capacitive Dimmable Switch Product number: 833.89.133 You can toggle devices on and off or dim lights by touching the enclosure constantly. Switch Door Product number: 833.89.059 If the sensor is pressed, the signal turns off otherwise on. Switch Door Modular Product number: 833.89.143 If the sensor is pressed, the signal turns off otherwise on. -
Page 8: Switch Rocker
The Häfele Connect Mesh 6 way distributor can be provisioned when the red Status-LED on the topside flashes. Start the Connect Mesh app and tap on “Add devices”. The box will be displayed in the list of devices found. Tap the icon to start the provisioning mode. Follow the instructions in the app. After provisioning, you can assign the individual functions to the box in the app. -
Page 9: Reset
3.7. Reset Option 1: Reset by App • In case the device is provisioned and connected to the app, the user can reset the mesh device via the Connect Mesh App (more information in the specific Häfele Connect Mesh App). Option 2: Manual Reset by Power On/Off • Switch ON/OFF the mesh device 8 times at consistent intervals of 2 seconds each. (Attention: Wait until the red status led is off before switching ON again.) -
Page 10: Q&A
4. Q&A Question Answer My RGB-LED-Band/Multi White LED-Band is Check the channel order connections. Be sure that the configuration of the not working like it should. The control sliders device channels match the order of how the device is connected. behave strangely. 10/10 © 2020 by Häfele GmbH & Co KG Subject to Adolf-Häfele-Str.