Panasonic HL-C201A-SP3 Instruction Manual

Ultra High-Speed, High-Accuracy Laser Displacement Sensor
Sensor Head
HL-C201A(E)-SP3, HL-C201A(E)-SP3M
Thank you very much for purchasing Panasonic products. Read this Instruction Man-
ual carefully and thoroughly for the correct and optimum use of this product. Kindly
keep this manual in a convenient place for quick reference.
● This product is intended to detect the objects and does not have the control func-
tion to ensure safety such as accident prevention.
Do not use the product as a sensing device to protect human body.
● Be careful not to directly watch or touch the direct laser beam or reflected laser beam.
● The product was developed and manufactured for industrial use.
BEFORE USE
● Before using the product, check the sensor head model and contents of packing.
● Sensor head model
Check the model name of product at the top of sensor
head.
● Packing
Check that all of the following components are includ-
ed in the package.
• 1 sensor head unit
• 1 Instruction manual
• Laser warning labels
[JIS/IEC/KS: 1 set, GB: 1 set (E type only)]
● This product satisfies the adaption of CE product by using in combination with
controller and programmable display, which are subjected to CE. Please confirm
that there is CE mark on connecting controller's label.
1 DESCRIPTION
● HL-C201A(E)-SP3, HL-C201A(E)-SP3M displacement sensor head achieves ul-
tra high-speed and high-accurate measurement using linear image sensor as light
receiving element to be used on equipment that require high-speed operation with
high-accuracy.
● The product is used at specular reflection installation.
2 CAUTIONS ON HANDLING LASER LIGHT
● In order to prevent the accident by laser product and protect the users, JIS C
6802 "Safety of laser products" was established based on the regulation of
-2014
IEC (International electrotechnical Commission). This regulation classifies laser
products according to the level of hazard, and provides the safety measures for
respective classes.
HL-C201A(E)-SP3, HL-C201A(E)-SP3M are classified as "Class 1 laser products"
according to IEC 60825-1 (JIS C 6802
-2014
● Laser hazardous class
Classification according to IEC 60825-1
Class Model
HL-C201A(E)-SP3
Class 1 Safe under reasonably foreseeable conditions of operation
HL-C201A(E)-SP3M
● WARNING label
In Japanese / English
/ Korean
In Chinese
(E type only)
● Install the product so the laser beam comes higher or lower than eye level in order
not to watch the beam directly during operation.
● Please contact our company if the system breaks down. It is not equipped with a
function that stops laser radiation automatically during disassembling the sensor
head. The users therefore may be exposed to laser beam in disassembling the
sensor head.
● When this product is used in China, affix the Chinese warning label (accessory)
on the label in the product.
● Do not use the system in the manner other than specified in this Instruction Manual.
INSTRUCTION MANUAL
CMJE-HLC201ASP3(03) No.0059-61V
WARNING
) "Safety of laser products".
-2014
(JIS C 6802 )
-2014 -2014
Description of hazardous evaluation
<Label position>
3 EXPORT REGULATIONS BY JAPANESE GOVERNMENT
● HL-C201A-SP3 and HL-C201A-SP3M are subject to export control regulation by
the Foreign Exchange and Foreign Trade Law. Export admission by Japanese
government is required before the product is to be exported or brought out of the
country. These products are also subject to Article 1.B.3.b.1 of Nuclear Suppliers
Group in international export control regime and 2.B.6.b.1 of Wassenaar Arrange-
ment.
● Please follow the export control regulations required.
HL-C201AE-SP3 and HL-C201AE-SP3M (E type) are not subject to export con-
trol regulations under the condition that they are used combined with the non-
pertinent controller to export control specified by Foreign Exchange and Foreign
Trade Law. When they are combined with the pertinent controller to export control,
they are subject to the Law. In this case export admission by Japanese govern-
ment is required before the product is to be exported or brought out of the country.
4 SPECIFICATIONS
Model No. HL-C201A(E)-SP3
Meas. method
Measurement center distance
Measurement range (Note 2)
Beam source
Max output: 0.3mW, Emission Peak wavelength: 658nm
Approx. ø30μm
Beam diameter (Note 3)
Beam receiving element
0.04μm / average times: 256, 0.01μm /average times: 4,096
Resolution
Linearity
Temperature characteristics
Laser emission
Meas. range Yellow LED: Near measurement center:ON, within measurement range:Blink, beyond the range:OFF
Protective structure
Pollution degree
Insulation resistance 20M ohms or more by 500V DC megger (between all the terminals and enclosure.)
Commercial Frequency AC 500V for 1min. (between all the terminals and enclosure.)
Impulse ±1,000V 1.2/50μs (between all the terminals and enclosure.)
Endurance: 10 to 55Hz (cycle: 1minute), Resistant amplitude of vibration: 1.5mm, in
Vibration resistance
X, Y, and Z directions for 2 hours
Shock resistance
Ambient illuminance (Note 6) 3,000ℓx or less (illuinance at beam receiving surface using incandescent lamp)
Ambient temperature 0 to +45°C (No dew condensation or icing allowed), At storage: -20 to +70°C
Ambient humidity
Ambient Height
Material Main unit case / cover faluminum: Die-cast, Front cover: Glass
Cable length
Cable extension Extendible to 30m long maximum using the optional extension cable.
Weight
Applicable regulations
Notes: 1) Measuring conditions are as follows unless otherwise specified; connection with controller, power voltage:
24V DC, ambient temperature: 20°C, sampling cycle: 40μs, average times:256, at measurement center dis-
tance, measurement subject: clear glass, and digital measurement value.
2) The measurement range is between +0.1 and +1.0mm (in case the sampling cycle is 20μs), or between +0.8
and +1.0mm (in case the sampling cycle is 10μs).
3) The figure shows the value at measurement center distance. It is determined by 1/e
of center beam intensity. Due to leak light outside the specified area, the reflectance around the detecting
point may be higher than at the point and this may affect the measurement value.
4) The minimum resolution of 0.25μm can be achieved if the sensor head is connected to the controller that is
not subject to "Foreign Exchange and Foreign Trade Law".
5) The linearity of ±0.025%F.S. can be achieved if the sensor head is connected to the controller that is not sub-
ject to "Foreign Exchange and Foreign Trade Law".
6) The variation in ambient illuminance is ±0.02%F.S. or less.
HL-C201A(E)-SP3M
Specular reflection
15mm
±1mm
Red semiconductor laser Class 1 (JIS/IEC/GB/KS)
Approx. 30 × 1,400μm
Linear image sensor
[E type (Note 4) 0.25μm / average times 256]
±0.02%F.S. [E type (Note 5) ±0.025%F.S.]
0.02%F.S./°C
Green LED: Lights up during laser emission.
IP67 (except connector)
2
196m/ s 2 in X, Y, and Z directions for 3 times
35 to 85%RH At storage:35 to 85%RH
2,000m or less
0.5m
Approx. 400g including cable weight
Conformed to EMC Directive
2 (approximately 13.5%)