Advertisement
5
CAUTIONS
Connection
● Turn off the power of controller before connecting or disconnecting the connectors.
● When connecting or disconnecting the connectors, be sure to hold the connector
area not to apply extra force to the cable.
● Be careful not to touch terminals or to let foreign matter get in the connector after
disconnecting connectors.
● Be careful not to apply force to around the connector of standard cable and ex-
tension cable. Do not bend the cables near connectors. Failure to do so causes
causes disconnection of the cable.
● When moving the sensor head during operation, install it so the cable not bend
bend during movement. Use replaceable extensions cable in case the cable
needs bend.
Wiring
● Do not run the sensor cable along (bundled in parallel) with other wirings. Keep it
at least 100mm away from other wires. Run the cable so it is separate from high
voltage and power circuit lines. If it is necessary to run the cable in parallel with
them, shield it by running through a grounded electrical conduit.
● Install the product as far away as possible from noise source such as high-voltage
lines, high-voltage device, power lines, power device, machines which generate a
large starting and stopping surge, welding machines and inverter motor.
● Do not pull the cable using a force more than 29.4N
when routing the cable with the sensor head and
controller fixed. At least 20 mm is required from the
cable connection to the bend. The bending radius
must be 30 mm or more.
● Use only 1 extension cable for connection between
one sensor head and a controller.
Warming up time
● Allow at least 30 minutes of warming up after turning on the power to ensure the
performance of the product.
Environment
● The life of the semiconductor laser depends on the ambient temperature during
use. When using the product near a heat source, take measures to lower the am-
bient temperature of the sensor head as possible. Mount the sensor on a device
having good heat radiation because the sensor itself emits heat.
● Water, oil, or fingerprints on the emitter surface and receiver surface of sensor
head reflects light. Dust and dirt on them block light. Keep them clean at all times.
When cleaning these parts, wipe them off using a soft lint-free cloth or lens clean-
ing paper.
● Install the sensor head so ambient light such as sunlight or light with the same
wavelength as laser beam should not enter the light receiver. If high accuracy is
required, install a light shielding plate or the like on the sensor head.
● The controller and connectors are not structurally dustproof, waterproof, or corro-
sion-resistant. Do not use the product underwater or in the rain.
● Do not use the product in dusty places or that exposed to flammable or corrosive
gases, droplet, direct sunlight, severe vibration or impact.
Setting
● The product is used at specular reflection installation. Set the "Installation Mode"
to Specular Reflection.
6
MEASUREMENT RANGE / INDICATOR
Meas. range indicator
OFF
Measurement center
distance
● The measurement range indicator at sampling cycle of 20μs or 10μs lights up at
the center of limited measurement range.
7
BEAM DIAMETER (Unit: mm)
ø0.14
HL-C201A(E)-SP3
Minimal spot type
Measurement center distance
1.25
HL-C201A(E)-SP3M
Line spot type
20mm or more
R30mm or more
Blink
ON
Blink
OFF
Measurement range
ø0.03
ø0.14
Measurement range
1.40
1.55
0.14
0.03
8
DIMENSIONS (Unit: mm)
Light emission axis
0.14
http://panasonic.net/id/pidsx/global
Overseas Sales Division (Head Office)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: +81-568-33-7861 FAX: +81-568-33-8591
About our sale network, please visit our website.
PRINTED IN JAPAN
Measurement range
indicator (yellow)
Laser emission
indicator
(green)
2-ø4.5 (mounting hole)
Light reception axis
© Panasonic Industrial Devices SUNX Co., Ltd. 2017
Advertisement
