Page 1
Seven Hills NSW 2147 Molendinar QLD 4214 info@oasisaquatics.com.au T: 03 9887 2131 T: 02 9838 0000 T: 07 5679 6821 oasisaquatics.com.au P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP info@oasisaquatics.com.au INSTALLATION AND OPERATION MANUAL oasisaquatics.com.au...
Page 2
Please pass these instructions on to the owner of this equipment. MODELS P270 (1.0HP) P330 (1.25HP) P380 (1.5HP) P490 (2.0HP) P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP info@oasisaquatics.com.au INSTALLATION AND OPERATION MANUAL oasisaquatics.com.au...
Page 3
• Ensure that an electrical isolation switch is located with easy access so that the pump can be switched off in an emergency. P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP info@oasisaquatics.com.au INSTALLATION AND OPERATION MANUAL oasisaquatics.com.au...
OASIS’S advanced pump technology provides reliable and efficient performance that lasts. OASIS pool and spa pump are designed with high flow and the head pressures are ideally suited for the modern pool or spa with extensive equipment.
If the supply cord of this product is damaged the dealer or manufacturer must replace it, with genuine OASIS pool and spa pump spares. • Water temperature is not to exceed 45 degrees P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP info@oasisaquatics.com.au INSTALLATION AND OPERATION MANUAL oasisaquatics.com.au...
Do not use type ‘P’ (green) plumber’s glue on the barrel unions as this may cause damage to the material used. Always install pump for maintenance and service accessibility. P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP info@oasisaquatics.com.au INSTALLATION AND OPERATION MANUAL...
Please consult your local pool shop regularly to have your water tested. P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP info@oasisaquatics.com.au INSTALLATION AND OPERATION MANUAL...
Page 8
6. Replace the lid and ensure that it seals on the large rubber o-ring. Firm hand tightness only is required. a. The o-ring & thread can be lubricated with silicone grease. P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP info@oasisaquatics.com.au INSTALLATION AND OPERATION MANUAL...
3. Remove the discharge & suction barrel unions taking care not to lose the o-rings. 4. Move the pipe work with the barrel unions attached until the pump can be moved clear. P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP info@oasisaquatics.com.au INSTALLATION AND OPERATION MANUAL oasisaquatics.com.au...
Page 10
• Barrel unions need to be hand tightened. No sealant, glues or silicones are required. • When making any enquiries about your OASIS pool and spa pump be certain to quote the model number from the nameplate located on motor.
12 month in field labour warranty is applicable in some Capital City Metropolitan areas or within a 20 km radius of an Authorised Oasis Service Agent. A travel fee may be charged on all other areas. Oasis shall have no liability for incidental or consequential damages. No person is authorized to make any representation or warranty on behalf of Oasis other than what is stated here.
Page 12
Queensland 62 Parkhurst Drive Unit 1, 20-22 Foundry Road Unit 4, 8 Reichert Drive P SERIES HIGH PERFORMANCE - P270 | P330 | P380 | P490 POOL & SPA PUMP Knoxfield VIC 3180 Seven Hills NSW 2147 Molendinar QLD 4214 info@oasisaquatics.com.au...