Advertisement
GAMMA wave
Technical Product Information
February 2007
Switch actuator wave GE 561/01
Commissioning
To control the switch actuator, both channels must first
be connected via radio to GAMMA wave radio sensors,
such as, e.g., pushbutton wave, transmitter wave, hand-
held transmitter wave, binary input wave, etc.
The connection is made by switching on the "special
function channel A" or "special function channel B" oper-
ating mode on the switch actuator, by correspondingly
long actuation of the pushbutton and display via the
LED. Subsequently, sending the program telegrams is to
be actuated at the GAMMA wave radio sensor to be
connected (see operating instructions for the corre-
sponding device).
The two channels of the switch actuator can be con-
nected to a total of up to 40 GAMMA wave radio sen-
sors.
Connection via radio:
Diagram F
F1
Switch actuator wave GE 561/01
F2
Pushbutton
F3
LED
F4
Radio button with GAMMA wave radio technology
F5
Insulated screwdriver
To connect a radio sensor to a channel of the switch ac-
tuator wave, the corresponding channel should be
switched to the "special function" operating mode.
Technical Manual
Update: http://www.siemens.de/gamma
2.20.8.1/4
F4
F3
F2
F5
F1
wave GE 561/01, 6 pages
Subject to change without prior notice
Special function for channel A:
A brief actuation of the pushbutton (F2) for the duration
of up to 3 seconds switches the actuator to the "special
function channel A" operating mode. This is displayed by
a slow flashing with approx. 0.5 Hz (once in 2 seconds)
of the LED (F3).
Special function for channel B:
A long actuation of the pushbutton (F2) for the duration
of 3 to 6 seconds switches the actuator to the "special
function channel B" operating mode. This is displayed by
a steady light of the LED (F3).
Programming a radio sensor.
To program a radio sensor to a channel of the switch ac-
tuator wave, carry out the following steps 1A or 1B, 2
and 3 one after the other:
1A. Switch on special function channel A.
Action:
Brief actuation of the pushbutton (F2) for the
duration of no more than 3 seconds.
Display:
Within 3 seconds after the release of the push
button the LED (F3) begins to flash slowly
(once in 2 seconds) with approx. 0.5 Hz.
or
1B. Switch on special function channel B.
Action:
Long actuation of the pushbutton (F2) for the
duration of 3 to 6 seconds.
Display:
Within 3 seconds the LED (F3) flashes once
briefly (approx. 0.1 sec.). Within 3 to 6 sec-
onds after the release of the pushbutton, the
LED shows a steady light.
The switch actuator wave waits for radio telegrams to
connect to a radio sensor.
2. Trigger program telegram at the radio sensor
wave.
Action:
Trigger the sending of the program telegrams
at the radio sensor (F4) to be connected
(switch to special function via DIP switch,
pushbutton, etc., depending on the device,
see operating instructions for the correspond-
ing device).
3. Successful connection.
Display:
After receipt of the program telegrams of the
radio sensor (F4) and successful connection,
the LED (F3) flashes quickly for the duration
of approx.3 seconds with approx. 2.5 Hz (3
times per sec.). Subsequently the LED clears
and the actuator exits the "special function"
operating mode.
© Siemens AG 2007
5WG3 561-4AB01
Siemens AG
Automation and Drives Group
Electrical Installation Technology
P.O. Box 10 09 53, D-93009 Regensburg
Advertisement
