Part Names; Specifications - Panasonic LC4H-S Series Manual

Part names

• 4-digit display type
Controlled output indicator
Reset indicator
Lock indicator
Reset switch
Set/lock switch
• 6-digit display type
Controlled output indicator
Reset indicator
Lock indicator
Reset switch
Set/lock switch

Specifications

Item
Rated operating voltage
Rated frequency
Rated power consumption
Rated control capacity
Input mode
Max. counting speed
Counting input (input 1, input 2)
Reset input
Lock input
Rating
Input signal
Output mode
One shot output time
Indication
Digit
Decimal point
Pre-scaling
Memory
Power for senser
Contact arrangement
Contact Initial contact resistance
Contact material
Mechanical (contact)
Life
Electrical (contact)
Operating voltage range
Initial withstand voltage
Electrical
Initial insulation resistance
(At 500 V DC)
Temperature rise
Functional
Vibration
resistance
Destructive
Mechanical
Functional
Shock
resistance
Destructive
Ambient temperature
Operating
Ambient humidity
conditions
Air pressure
Connection
Protective construction
COUNTER LC4H
O P .
R S T
L O C K
UP
RESET
SET/ LOCK
DOWN
COUNTER LC4H
O P .
R S T
L O C K
RESET
SET/ LOCK
Ralay output type
AC type
100 to 240 V
Max. 10 V A
5 A 250 V AC (resistive load)
Addition (UP)/Subtraction (DOWN)/Direction (DIR)/Individuality (IND)/Phase (PHASE)
16.7 ms at 30 Hz/0.1 ms at 5 kHz ON time: OFF time = 1:1
Min. input signal width: 1 ms, 20 ms (selected by DIP switches)
Contact, Open collector input/DC two-wire system sensor Input impedance: 1 kΩ or less, Input residual voltage: 2 V or less,
Open impedance: 100 kΩ or less, Max. energized voltage: 40 V DC
HOLD-A, HOLD-B, HOLD-C, SHOT-A, SHOT-B, SHOT-C, SHOT-D, 7 modes selectable by DIP switches
7-segment LCD, Counter value (backlight red LED), Setting value (backlight yellow LED)
6-digit display type –99999 to 999999 (0 to 999999 for setting)
0.001 to 9.999 (4-digit type), 0.001 to 99.999 (6-digit type)
12 V DC (±10%) 100 mA Max.
100 mΩ (at 1 A 6 V DC)
Ag alloy/Au flush
2.0 × 10
7 ope. (Except for switch operation parts)
1.0 × 10
5 ope. (At rated control voltage)
85 to 264 V AC
Between live and dead metal parts: 2,000 Vrms for 1 min (pin type)
Between live and dead metal parts: Min. 100 MΩ (pin type)
Max. 65° C (under the flow of nominal operating current at nominal voltage)
10 to 55 Hz (1 cycle/min), single amplitude: 0.35 mm
10 to 55 Hz (1 cycle/min), single amplitude: 0.75 mm
02/2003
Counter display
Set value display
Up keys
Down keys
Counter display
Set value display
Up keys
DC/AC type
12 to 24 V DC/24 V AC
50/60 Hz common
5 modes selectable by DIP switches
30 Hz, 5 kHz (selectable by DIP switches)
Min. input signal width: 20 ms
1 s, 0.5s, 0.2s, 0.1s, 0.05, 0.01s
4-digit display type –999 to 9999 (0 to 9999 for setting)
Can be set to three digits
EEP-ROM (Overwriting times: 10
1 Form C
10.8 to 26.4 V DC, 20.4 to 26.4 V AC
Between input and output: 2,000 Vrms for 1 min
Between input and output: Min. 100 MΩ
Min. 98 m/s 2 (4 times on 3 axes)
Min. 294 m/s 2 (5 times on 3 axes)
–10° C to 55° C +14° F to +131° F
Max. 85 % RH
860 to 1,060 h Pa
11-pin/screw terminal
IP66 (front panel with a rubber gasket)
DIP switches
1 2 3 4 5 6 7 8
(Same for screw terminal type)
DIP switches
1 2 3 4 5 6 7 8
(Same for screw terminal type)
Transistor output type
DC/AC type
12 to 24 V DC/24 V AC
Max. 3 W
100 mA, 30 V DC
5 ope. or more)
—
1 Form A (Open collector)
—
—
—
1.0 × 10
7 ope. (At rated control voltage)
.014 inch (10 min on 3 axes)
.030 inch (1 h on 3 axes)
LC4H-S
83