Advertisement
RPK5-GM4102
Interface Installation Steps (cont.)
4. The Mute loop (if not cut) will turn the accessory output off when an OnStar or Bluetooth call is made or received. If the aftermarket radio has a
mute input, cut this loop and connect the outer Brown wire to the mute input.
5. Connect the SWC wire according to the chart on page 4 (aftermarket radio MUST support a wired remote input).
6. If you wish to reassign functions to the SWC follow the programming instructions in the next section.
7. Connect the proper AUX cables depending if your vehicle has the MyLink or standard non-touchscreen radio equipped with a USB port.
8. Connect the supplied USB retention cable. MyLink radios will have a mini USB cable behind the radio. In this case the USB-GM1 cable (sold
separately) can be used. The supplied cable will need to be ran to the back of the factory USB port located at the rear of the center console.
USB and AUX cable Installation
1. Use a flat bladed plastic trim tool and release the retainer clips
securing the console's (1) right and (2) left side covers to the front
floor console assembly.
2. Move the front seats to the forward most position.
3. Remove the 4 Phillips head bolts (3) securing the console's rear
cover (4) to the front floor console.
4. Remove the front floor console rear cover (4).
5. Remove the electrical connections from the back of the AUX and
USB panel located inside the center console.
6. Connect the RPK5-GM4101-AUX-HAR and the RPK5-GM4101-
USB-HAR (if the vehicle is equipped with factory AUX).
7. Route the new AUX and USB cables down the driver side and
using a fish tape, route the cables up into the radio cavity.
Default Steering Wheel Assignments
IMPORTANT!
The interface comes pre-programmed for the functions listed in the chart below and does not require programming unless you
wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC functions can always be restored to
default settings by pressing the program button on the side of the interface once and waiting for the time out.
The Mute/End button has two functions. Pressing this button for less than 1.5 seconds will initiate the mute command. Pressing this button for
more than 1.5 seconds will initiate the end command. This dual function button can also be reprogrammed to whatever features the customer
chooses.
Default SWC Button Assignments
Volume +
Volume -
Source
Track +
Track -
Answer/Voice
Mute/End
Optional Steering Wheel Control Programming
If you wish to re-assign the SWC functions or utilize short press long press dual command functionality, the interface must be programmed in
the specific order shown in the chart on the next page. If you come across a function in the chart that your steering wheel does not have, or you
do not want to program, press and release the program button on the side of the interface to skip that function. The LED will flash off and on
confirming that you have successfully skipped that function and are ready to proceed to the next one.
Short Press Long Press Dual Command Functionality
This feature allows you to assign two aftermarket radio functions to each of the vehicle's SWC buttons. It can be used with as many of the
buttons as the user likes or none at all. When this functionality is implemented, quickly pressing and releasing a SWC button will initiate the short
press command, while pressing and holding a SWC button for longer than two seconds will initiate the long press command. Please note that
all buttons except the Mute button do not have a long press command programmed by default. If you wish to assign dual command functionality
to the SWC please follow the programming steps on the next page.
Pacific Accessory Corporation
Alpine
JVC
Kenwood
Volume +
Volume +
Volume +
Volume -
Volume -
Volume -
Source
Source
Source
Track +
Track +
Track +
Track -
Track -
Track -
Answer/OnStar
Answer/OnStar
Answer/OnStar
Activation
Activation
Activation
Mute/Factory
Mute/Factory
Mute/Factory
Bluetooth End
Bluetooth End
Bluetooth End
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
Email - support@pac-audio.com - Phone: 727-592-5991
Complete Radio Replacement Kit with Integrated Climate
Control Retention for 2010-2015 Chevrolet Camaro
Clarion/
Pioneer
Nakamichi
Volume +
Volume +
Volume -
Volume -
Source
Source
Search +
Track +
Search -
Track -
Answer/OnStar
Answer/OnStar
Activation
Activation
Mute/Factory
Mute/Factory
Bluetooth End
Bluetooth End
PAC-audio.com
Sony
Fusion
Volume +
Volume +
Volume -
Volume -
Source
Source
Track +
Track +
Track -
Track -
Answer/OnStar
Answer/OnStar
Activation
Activation
Mute/Factory
Mute/Factory
Bluetooth End
Bluetooth End
Rev: R6
Date: 010419
Page 5
Advertisement
