Condensate Drain 4; Dimensions And Clearances - York SUNLINE 2000 D1EE 048 Installation Instruction

035-12046-003-A-0204
(Direct-Drive Units)
FIELD-SUPPLIED
DISCONNECT SWITCH
LOCATION
CONTROL
FILTER ACCESS
BOX ACCESS
#
&
" PVC FEMALE
"
COND. DRAIN
""
(See Detail "A") %
&
A, B
WIRING ENTRY
(See Detail "B")
#
&
%
%
BOTTOM SUPPLY &
RETURN AIR OPENINGS
(SEE NOTE)
B - POWER WIRING ENTRY
A - CONTROL WIRING ENTRY
CLEARANCES
Front
Back
Left Side (Filter Access)
Right Side (Cond. Coil)
1
Below Unit
2
Above Unit
NOTE:
Units and ductwork are approved for zero clearance to combustible
materials when equipped with electric heaters.
1
Units may be installed on combustible floors made from wood or
class A, B or C roof covering material. (Applicable in USA only).
2
Units must be installed outdoors. Overhanging structures or shrubs
should not obstruct the outdoor coil nor the fan outlet.
%
'
DETAIL "A"
UNIT WITH ECONOMIZER RAIN HOOD
FIG. 5 - DIMENSIONS & CLEARANCES - 3 - 5 TONS
Unitary Products Group
BLOWER
ACCESS
FRONT VIEW
&
%
$
%
$
"
&
UNIT BASE WITH RAILS
&
&
Shown separately to illustrate bottom
duct openings and power connection
locations.
NOTE: For curb-mounted units, refer to the
duct hanger dimensions of the curb for the
proper size of the supply and return air
& duct connections.
&
24"
12" (Less Economizer)
36" (With Economizer
or Fixed Air/Motorized
Air Damper)
24" (Less Economizer)
36" (With Economizer)
24"
20"
72" (For Condenser Air
Discharge)
" CONDENSATE
"
DRAIN
(must be trapped)
'
"
""
%
&
OUTDOOR
COIL
COMPRES-
SOR
ELECTRIC
HEAT
ACCESS
"
%
$
%
REAR VIEW
SIDE SUPPLY AND RETURN
AIR OPENINGS
AIR FLOW LEGEND
RETURN AIR
SUPPLY AIR
%
&
OUTDOOR AIR
'
OUTDOOR AIR
&
(Economizer)
DIMENSION "A"
FIXED
OUTDOOR 12
AIR DAMPER
MOTORIZED
$
DAMPER
DUCT COVERS - Units are shipped with all air duct
openings covered.
For side duct applications;
1.Remove and discard the supply and return air duct
covers.
2.Connect ductwork to duct flanges on the rear of the
unit.
For bottom duct applications;
1. Remove the side supply air duct cover to gain
access to the bottom supply air knockout panel.
2. Remove and discard the bottom knockout panel.
3. Replace the side duct cover.
4. With filter section access panel removed from the
unit, remove and discard the bottom return air
knockout panel.
5. Replace the filter access panel.
All dimensions are in inches. They are sub-
ject to change without notice. Certified di-
mensions will be provided upon request.
UTILITIES ENTRY DATA
3
KNOCKOUT
HOLE SIZE
(DIA.)
"
#
&
A 7/8" *
%
% B 2" *
&
*
Knockouts in the bottom of the unit can be
located by the slice in the insulation.
**
Do not remove the 2" knockout ring.
"A"
""
%
&
DETAIL "B"
UNIT WITH FIXED OUTDOOR
AIR/MOTORIZED DAMPER RAIN HOOD
USED FOR
Control Wiring
(Side or
Bottom)**
Power Wiring
(Side or
Bottom)
"
B
A
&
"
"
&
7