Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Maxell MXIP-100
Summary of Contents for Maxell MXIP-100
-
Page 2: Table Of Contents
PA1777 - 00 Intense Pulsed Light Device MXIP - 100 User Manual Thank you for purchasing Maxell product. Please read the user manual in advance and use the product safely. Contents Content of the package Introduction Safety Precaution Features Part Names... -
Page 3: Content Of The Package
Disclaimer ・ Maxell shall not be responsible for any damage caused by res, earthquakes, action of a third party, any accidents, intended or unintended misuse or other usage under abnormal conditions. ・ All explicit and implicit contents not stated in the warranty card are not covered. - Page 4 Prohibited actions when handling the product. The shape of graphic symbol that indicates speci c notes is shown in black. Caution to re, explosion, high temperature when handling the product. The shape of graphic symbol that indicates speci c notes is shown in black. instruction which must be followed when handling the product.
- Page 5 Warning Do not cover the power adapter with a cloth or a cover Do not splash or soak in water Heat will accumulate and cause deformation of the case, It may cause electric shock or malfunction. fire or electric shock. Do not use with wet hands Do not use a power adapter other than the provided power adapter...
-
Page 6: Features
Features This product is a device that irradiates the skin with light to remove unwanted hair. A cooling plate is installed around the irradiation window to cool down the skin at the same time as irradiation. It lessens the pain and heat during irradiation and gently cares for the skin. Cooling Plate The plate gets cold when the power is turned on. -
Page 7: Part Names
Part Names Main Unit Air Outlet Skin Detection Sensor Irradiation Window Power Button Cooling Plate Long Press : Power ON/OFF Short Press : Output level Switch (1-5) Air Inlet Multi-Function Button Long Press : Single Mode/ Continuous Mode Select Switch Main Unit Bottom Air Outlet Short Press:... -
Page 8: Sites Where The Device Can Be Used
Recommended Treatment Area The time is an approximate time when used at level 1. Face (Female only） approx. 1 min ※Do not use above the cheekbones. Areas that cannot be irradiated. Armpit approx. 2 mins Bikini line approx. 2 mins Legs approx. - Page 9 Areas that can be irradiated. Arms approx. 6 mins Finger approx. 1 min Chest・ Abdomen （Male Only） approx. 3 mins each ※Do not use on areola. The device cannot irradiate without touching the ※Do not use on navel. skin detection sensor.
-
Page 10: Frequency Of Use
Frequency of Use First week once 1 week week once 1 or 2 weeks week once 9~12 2 weeks or 1 month If hair growth is no longer seen, it is not necessary to perform the treatment as often as above. If hair becomes visible again, perform the treatment as needed. -
Page 11: Operation Instructions
Operating Instructions Caution ・Please keep the room bright when using.・Storage light will be generated when irradiating, please make sure that there are no people or pets nearby.・Strong light is emitted during use. Be careful not to look directly at the area of use. • When using on face, please close your eyes. - Page 12 The mode can be switched by long pressing the multi button (for 2 seconds). Select the mode to use. Switch the Single Mode When you want to perform a treatment for a mode small area or sensitive area Continuous When you want to e ciently care for a wide irradiation mode area *Continuous mode is a mode of continuously...
- Page 13 Continuous Mode Make sure there is no gap between the irradiation window and the ❶ area you want to irradiate. Press against the area you want to If the skin detection sensor is not in contact with the skin, the device cannot irradiate.
-
Page 14: Maintenance
Maintenance ・Always stop operation and unplug the power plug from the power outlet when cleaning. ・Just after use, the irradiation window and cooling plate will still keep the temperature, so please cool down a little before cleaning. ・Gently wipe off the irradiation window, cooling plate, and main unit with a dry cloth. -
Page 15: Device Disposal
DC12V/4A Max. Main Unit Input voltage / current Max. 48W Power consumption C ~ 35 Operation Temperature AC100-240V 50/60Hz Input Power Adapter DC12V/4A Max. Output approx. 1.8m Length Approx. 1.5m Power Cable Length Maxell, Ltd. 30-13 Motoyoyogi-Cho, Shibuya-Ku, Tokyo 151-8527...
Need help?
Do you have a question about the MXIP-100 and is the answer not in the manual?
Questions and answers