Honeywell Performance Series Quick Installation Manual page 2

Preparing the Mounting Surface
1. Apply the mounting template to the mounting surface.
2. Using the mounting template as a guide, drill three pilot holes in the mounting surface,
then hammer the supplied anchors into the holes.
3. Drill a cable entry hole in the mounting surface, then pull the required cables through the hole.
Mounting and Aiming the Camera
1. Remove the dome cover from the camera assembly using the supplied Allen key.
2. If you are using a microSD card with the camera, install it before continuing. See below for
details.
1. Push and
slide metal
shell to unlock
position.
3. Connect the Ethernet cable to the RJ-45 port on the camera.
4. If the other end of the Ethernet cable is not connected to a PoE (Power-over-Ethernet)
switch or NVR, connect the power connector of the camera to a 12 VDC power source.
5. Fix the camera assembly to the mounting surface using the supplied screws.
6. Aim the camera lens in the desired direction, then tighten the screws on the camera assembly.
7. Reattach the dome cover.
Logging On to the Camera
If the camera is connected to the PoE port of a Honeywell Embedded NVR, it can be configured
using the NVR.
To log on remotely from a PC, install the Honeywell Config Tool from the software and
documentation CD, find the camera on the network, and then open the web browser with the
Honeywell Config Tool. The default user name is admin (case-sensitive) and the default password
is 1234.
• Only Internet Explorer 11 (or later) is supported.
Note
•
IP address of the device is assigned automatically by DHCP server. If the DHCP
server is not available, the device will acquire 192.168.1.108 as the default IP
address.
© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such changes.
2. Open 3. Insert microSD 4. Close metal
metal shell. card. shell and slide to
lock position.
Recommended Recorders
HEN*4 8/16/32/64-channel Focus 4K NVRs (H.264 and H.265)
HEN*3 4/8/16/32-channel Performance Series NVRs (H.264 and H.265)
HEN*2 4/8/16-channel Performance Series NVRs (H.264)
HRHT4* 4/8/16-channel 4 MP HQA/IP/CVBS Hybrid DVRs (H.264)
Regulatory Statements
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his
own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Manufacturer's Declaration of Conformance
North America The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.
Europe The manufacturer declares that the equipment supplied is compliant with the European Parliament
and Council Directive on the restriction of the use of certain hazardous substances in electrical and electronic
equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and the essential requirements of
the EMC directive (2014/30/EU), conforming to the requirements of standards EN 55032 for emissions, EN
50130-4 for immunity, and EN 62368-1 for electrical equipment safety.
CAUTION
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
WEEE (Waste Electrical and Electronic Equipment)
Correct disposal of this product (applicable in the European Union and other European countries with
separate collection systems). This product should be disposed of, at the end of its useful life, as per
applicable local laws, regulations, and procedures.
2700 Blankenbaker Pkwy, Suite 150 Aston Fields Road, Whitehouse Industrial
Louisville, KY, 40299, USA Estate Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security www.honeywell.com/security/uk
+1 800 323 4576
(North America only)
Document 800-24597 – Rev A – 08/2018
Building #1, 555 Huanke Road, Zhang
Jiang Hi-Tech Park
Pudong New Area, Shanghai, 201203,
+1 44 (0) 1928 754 028
China www.asia.security.honeywell.com
(Europe only)
+400 840 2233
(Asia Pacific only)