Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Del Morino BM Series
Summary of Contents for Del Morino BM Series
- Page 1 Del Morino srl , v.Caroni di Sotto 19, I-52033 Caprese Michelangelo AR Italy Ph: +39-575-791059 Fax: +39-575-791210 E.mail: export@del-morino.it http://www.del-morino.it USE AND MAINTENANCE MANUAL BRUSH MOWER TYPE BM / SC - 2008 BMUsa-e-06.doc Use and maintenance manual : BM - SC...
-
Page 2: Preface
PREFACE This manual is an integral part of the machine. It must always accompany the machine and be kept within reach of the operator. The enclosures mentioned are on integral part of this manual. The purpose of this manual. This manual gives information for the correct and safe use of the machine. The owner must read this manual carefully before work with the machine. -
Page 3: Description
DESCRIPTION UNCTION OF USE This machine, thanks to its versatility, accomplishes both the function of mower and brush mower. The quickly and easy application of various device types, permit to obtain a good finishing in grass cutting (with fixed blade) and a radical scrub clearing (with jointed blade). ERFORMANCES The machine is connected with the walking tractor with a joint that besides to transmit the power allows a rotation of the machine around its longitudinal axis that aids adaptability with any ground. -
Page 4: Technical Specification
TECHNICAL SPECIFICATION HARACTERISTICS PER MODEL Model Type Power Cutting width Cutting height Blades Blades Weight speed g/min Inch Inch N° r.p.m. 21 BCS 6÷10.5 2.4÷4.15 2400 21 GRI 6÷10.5 2.4÷4.15 2400 26 BCS 6÷10.5 2.4÷4.15 2400 26 GRI 6÷10.5 2.4÷4.15 2400 31 BCS 6÷10.5 2.4÷4.15... -
Page 5: Safety Information
SAFETY INFORMATION ENERAL REGULATIONS Only work in daylight. To prevent damage due to lunch of objects or parts of blades, before to start job be sure that any persons or animals should be in the radius of 50 meters from the machine. Wear long pants and heavy shoes. -
Page 6: Safety Signs On The Machine
SAFETY SIGNS ON THE MACHINE In this section the safety signs on the machine are reproduced and explained. WARNING DANGER DANGER 1. Read the operator manual. 2. Danger. 3. Danger, stay at safety distance from blades until machine moves. The safety signs on the machine must always be legible. In case of damage, the labels of the signs must be substituted. -
Page 7: Instructions For Use
INSTRUCTIONS FOR USE EFORE BEGINNING WORK a) Adjust front baffle opening as follows: 1. Unscrew and take out the two screws "L" and unscrew the two screws “I” on two machine sides. 2. Adjust position of baffle "H". 3. Plug in and lock screws "L", lock the screws “I”. b) Adjust cutting height operating as follows : 1. -
Page 8: To Beginning Work
O BEGINNING WORK a) Keep people and animals at least 65 feet radius all around the machine. b) Raise the machine from ground. c) Connect PTO power and gradually bring it to good speed. d) Pull down slowly the machine and start the work. T THE END OF WORK a) Stop the walking tractor. -
Page 9: Maintenance Instruction
MAINTENANCE INSTRUCTION On schedule "A" the maintenances are indicated with their terms to effect on the machine. Not follow the scheduled terms can compromise the functionality of the machine and in this case the warranty is not applicable. CHEDULA "A" - SCHEDULED MAINTENANCE FIRST AFTER 10 EACH 30... -
Page 10: Greasing
REASING The only greasing point is equipped with greaser HYDRAULIC TYPE MODEL “A” UNI 7663. To grease use only MULTIFUNCTIONAL GREASE LITHIUM BASED Type NLGI 2. The only greasing point is the point “C” located on one side of the hub. Greasing operation must be made at the terms scheduled on schedule “A”. -
Page 11: Blade Substitution
LADE SUBSTITUTION a) To change blade, operate as follows: 1. Unscrew nut "A" and take off pin "D" with respective spacer “B” from blade "C". 2. Plug in pin "D" in new blade putting pin head in the suitable slot, insert the spacer “B”. 3. -
Page 12: Problems Solving
PROBLEMS SOLVING TROUBLES GROUNDS AND SOLUTIONS -Damaged blade - Replace Abnormal vibrations -Broken blade - Replace -Not balanced blade - Balance -Not sharp blade - Sharp Uneven or unsatisfactory cut... -
Page 13: Transport
TRANSPORT Except when working, moving the machine takes place when the machine is standing still and the transmission is disconnected. <Important>: keep speed low avoiding holes and ground roughness. <Important>: Before begin the movements always make sure that the safety hooks be in position. <Note when on the road, obey existing traffic laws. -
Page 14: Work And Maintenance Sheet
WORK AND MAINTENANCE SHEET Every user should register on this sheet the facts about the life of the machine (both work and maintenance), so as to attest its conditions. DATE WORKING MAITENANCE NOTE USER HOURS... -
Page 15: Your Observation For Improvements
YOUR OBSERVATION FOR IMPROVEMENTS Customers can record on this sheet any observations on the performance of the machine, including possible problems. Observations coming directly from the work field are of great help in improving the product. We now thank those who will give us this help. SPARE PARTS ORDERS If you must order some spare parts, please follow these instructions : Take the spare parts list and the spare parts drawing enclosed in this manual. - Page 16 SPARE PARTS...
-
Page 17: Bm21 - Bm26 - Bm31 / 2008 Bcs Spare Parts
BM21 – BM26 – BM31 / 2008 BCS SPARE PARTS... -
Page 18: Bm21 - Bm26 Grillo / 2008 Grillo Spare Parts
BM21 – BM26 GRILLO / 2008 GRILLO SPARE PARTS... -
Page 19: Sc53 - Sc67 / 2008 Spare Parts
SC53 – SC67 / 2008 SPARE PARTS... -
Page 20: Table Of Contents
TABLE OF CONTENTS PREFACE ..................................2 DESCRIPTION ................................. 3 PERFORMANCES ............................... 3 PERFORMANCES LIMIT............................3 STANDARD EQUIPMENT ............................3 TECHNICAL SPECIFICATION ............................. 4 SAFETY INFORMATION ............................... 5 GENERAL REGULATIONS ............................5 SAFETY RESTRICTIONS ............................
Need help?
Do you have a question about the BM Series and is the answer not in the manual?
Questions and answers