Do you have a question about the FR-C21 and is the answer not in the manual?
Questions and answers
Robert Repasi
January 19, 2025
The power light is flashing. Can not to turn on. What can I do?
1 comments:
Mr. Anderson
May 14, 2025
If the power light on your anko FR-C21 is flashing and it won't turn on, follow these steps:
1. Make sure the power adaptor is plugged into both the appliance and a working power point. 2. Switch on the power at the power point. 3. Check the power point by testing it with another device, like a table lamp. 4. If the power point has no power, contact an electrician. 5. Press the On/Off button on the appliance. 6. If still not working, refer to the “No Power” section for further troubleshooting.
If none of these steps work, the issue may be with the power adaptor or internal components.
Page 1
Back & Thigh Massager User Manual Model No.: FR-C21 Rev 3 Note: The specifications and/or components of this appliance are subject to change without prior notice.
Warnings ................4 Important Safeguards ............4 Introduction ................ 7 Components ............... 8 Operation Procedure ............9 Set Up .................. 9 Power ................10 Massage Control Operation ..........10 Back Massager / Heat ............10 8.1.1 Full Back Massage ..............11 8.1.2 Upper Back Massage ............
1 Warnings We recommend checking with your doctor before using the massager, especially if you have health problems. Before using this appliance, read and follow all warnings and instructions in this manual, even if you are familiar with this product. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the...
Page 5
In case of pregnancy, diabetes or illness, consult your doctor before using this product. Massage should be pleasant and comfortable. Should pain or discomfort result, or if you experience pain in a muscle or joint for a prolonged period of time, stop use and consult your doctor.
Page 6
The appliance should always be switched off before disconnecting from the power supply. Never pull the cord to disconnect the power adaptor from either the appliance or the power point. Grasp the plug / adaptor body. There are no user serviceable parts in this appliance. If this appliance is to be used by a third party, please supply the instruction manual with it.
If the power adaptor or power adaptor supply cord is damaged, do not use. It must be disposed in order to avoid a hazard. ONLY for indoor domestic use. Industrial or commercial use invalidates the warranty. No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling of appliance.
4 Components Massage Body - Back Power Jack Socket Power Adaptor CW1203000AU Massager Controller Massage Seat Body - Thigh Controller Storage Pocket Elastic Straps Page 8 of 16...
5 Operation Procedure Note: Avoid using the massager before going to sleep or in conditions where you may fall asleep when using the massager. The unit will automatically turn off after approximately 15 minutes. Do Not use for more than 15 minutes at a time without a 30 minute cool down period in between uses.
7 Power Before first use, please read the Instruction Manual carefully. • Connect the small cable jack of the power adaptor to the massage appliance. • Insert the Power Adaptor Plug into the power point and switch on. • • The appliance is now ready for use.
8.1.1 Full Back Massage Press the “FULL” button. The indicator light illuminates and the rotating • massage fingers start to rotate. At the same time, they will travel the full height of the seat back, pause for a second, the rotating massage fingers will reverse rotation direction, and will then travel all the way down again.
To stop the massage fingers rotating at a particular spot, so as to apply heat in • one particular area, press the “LOWER” button when it reaches your desired position and then ensure the Heat function has been turned on. After approximately 15 minutes, the unit will automatically turn off.
10 Cleaning the Appliance CAUTION: DO NOT IMMERSE IN WATER OR LIQUID. Turn off and unplug appliance prior to cleaning. • Do Not immerse the appliance in water, or any other liquid. • • Clean only with a soft, very slight damp sponge. NEVER allow water or any other liquids to come into contact with the appliance •...
11 Troubleshooting Problem Cause Remedy Plug in power adaptor and Switch On at power point. If still no power, check the power point Power Not Switched On. has power supplied by checking with another appliance such as a table lamp. No Power.
12 Warranty Against Defect 12 Month Warranty Thank you for your purchase from Kmart. Kmart Australia Ltd warrants your new product to be free from defects in materials and workmanship for the period stated above, from the date of purchase, provided that the product is used in accordance with accompanying recommendations or instructions where provided.
Need help?
Do you have a question about the FR-C21 and is the answer not in the manual?
Questions and answers
The power light is flashing. Can not to turn on. What can I do?
If the power light on your anko FR-C21 is flashing and it won't turn on, follow these steps:
1. Make sure the power adaptor is plugged into both the appliance and a working power point.
2. Switch on the power at the power point.
3. Check the power point by testing it with another device, like a table lamp.
4. If the power point has no power, contact an electrician.
5. Press the On/Off button on the appliance.
6. If still not working, refer to the “No Power” section for further troubleshooting.
If none of these steps work, the issue may be with the power adaptor or internal components.
This answer is automatically generated