Wurtec S3 Communicator Master Station Manual
Hide thumbs
Also See for S3 Communicator Master Station:
- Manual (24 pages) ,
- Instructions manual (20 pages) ,
- Quick start manual (2 pages)
Subscribe to Our Youtube Channel
Related Manuals for Wurtec S3 Communicator Master Station
Summary of Contents for Wurtec S3 Communicator Master Station
- Page 1 S3 Communica tor ASTER TATION Use with Part Numbers 11-598-H1A through 11-598-S1A Version 2.0 October 2008...
-
Page 2: Table Of Contents
Before Programming the Wurtec Master Station ........ -
Page 3: Getting Started
If there is any damage call us for advice at 800-837-1066 or call our tech line at 419-930-1066 Telephone Line Intercom Out to Phones External 12-24 VAC/DC Earth Ground Isolated Program Keys Battery (BAT) Microphone (MIC) Speaker (SPK) LED (LED1) Buy Online! Wurtec.com... -
Page 4: Connection Diagram
Connection Diagram Buy Online! Wurtec.com... -
Page 5: General Master Station Information
In the instance that this event occurs the Master Station can still call the S3C emergency elevator phones because the system can also be used as an intercom automatically should this event occur. Buy Online! Wurtec.com... -
Page 6: Using The Master Station
After the conversation is over press the key again to hang up the Master / END Station. Hanging up the handset will NOT hang up the phone, it will just put the Master Station into speakerphone mode. Buy Online! Wurtec.com... -
Page 7: Programming S3C From Master Station
TALK elevator phone. Then press to hang up the Master Station. Hanging up / END the handset on the Master Station will NOT hang up the phone, it will just put the Master Station in speakerphone mode. Buy Online! Wurtec.com... -
Page 8: Introduction
Introduction There are two ways to program the Wurtec S3C: 1) locally [using onboard keypad and battery or external power supply] or 2) remotely [accessing the S3C from another location by calling it]. We recommend programming LOCALLY. Power Requirements: External 12-24V AC/DC isolated from earth ground at 200 mA or higher. -
Page 9: Quick Set-Up (From Onboard Keypad)
TALK Continue to press and release the keys until the desired volume / END VOL DN is reached. The “beep” tone will gradually decrease. The phone will say “Invalid Entry” one it has reached its lowest volume. Buy Online! Wurtec.com... -
Page 10: Adjusting Conversation Volume
/ END VOL DN reached. The phone will say “Invalid Entry” once the lowest volume is reached. TALK When fi nished press to hang up the phone. / END Buy Online! Wurtec.com... -
Page 11: Resetting To Factory Defaults
Maintenance Announcements - Off Ring Count - 1 Ring Volume - Mid Level (4) Emergency Phone Numbers - None Site ID Message - None Announcements - None Talk Time - 180 seconds Touch Tone ID - None Buy Online! Wurtec.com... -
Page 12: Installation
There are three in car local announcements for notifying which of the possible three emergency numbers are being dialed. STEP 1 PROG Press button. MENU STEP 2 Press for message menu. (continued on next page) Buy Online! Wurtec.com... -
Page 13: Programming (Locally Or Remotely) | Advanced Options
Press to review whether or not announcements are on or off. Press to turn off announcements. Press to return to the previous menu to VOL DN continue programming. Or press then to disconnect. VOL UP Buy Online! Wurtec.com... -
Page 14: User Preferences - Maintenance Announcements On/Off
MENU STEP 2 Press for advanced options. STEP 3 Press for talk time. STEP 4 To program a different talk time than the default 180 seconds (3 minutes) press (continued on next page) Buy Online! Wurtec.com... -
Page 15: Access Code
STEP 5 Press to return to the previous menu and continue on programming. If you are VOL DN fi nished programming you can press then to exit program mode. VOL UP Buy Online! Wurtec.com... -
Page 16: Ring Count
Once you have chosen an option in step 4 you can at this point press to return VOL DN to the previous menu to continue with programming. If you are fi nished you can press then to exit program mode. VOL UP Buy Online! Wurtec.com... -
Page 17: Program Status
At this point the phone will automatically revert back to the main program menu. You can choose any option to continue with programming. If you are fi nished you can press then to exit program mode. VOL UP Buy Online! Wurtec.com... -
Page 18: Calling Into Remote Phone
If you do not know the Access Code you must go to the job site and gain access to the circuit board keypad and reset to factory defaults or change the access code. If you are unable to get to the job site, you can call Wurtec Inc. All phone numbers are listed on troubleshooting page 20. -
Page 19: Phone Line Volume
/ END VOL DN the desired volume is reached. The phone will say “Invalid Entry” once the lowest TALK volume is reached. When fi nished press to hang up the phone. / END Buy Online! Wurtec.com... -
Page 20: Flowchart
9V battery connected to the phone. The 9V battery energizes the keypad when programming outside of the elevator. CAUTION when connecting the phone to external power be sure the 9V battery is rechargeable, otherwise you could damage the phone. Buy Online! Wurtec.com... - Page 21 Have a Good Telephone Line but Phone Says “Telephone Line Failure” Wurtec supplies a 12VAC isolation transformer with the phone. This transformer should be used with the phone. If you are getting a power source directly from the controller, it can create a ground loop with the telephone line and cause the phone to malfunction.
-
Page 22: Glossary
A typical site ID message should consist of: building name, address, elevator number if more than one is present, and a callback number. Telco Telephone Line Buy Online! Wurtec.com... -
Page 23: Warranty Policy
A defective product, shall be returned to Wurtec Inc. identifi ed with our return authorization number and freight prepaid, within fi fteen (15) days after discovery of possible defect. Wurtec Inc. reserves the right to request proof of purchase as well as other proof to document warranty claim. - Page 24 6200 Brent Drive, Toledo, Ohio | Ph: 800.837.1066 | Buy Online! wurtec.com...
Need help?
Do you have a question about the S3 Communicator Master Station and is the answer not in the manual?
Questions and answers