Wurtec S3 Communicator Manual
Building powered.
Hide thumbs
Also See for S3 Communicator:
- Manual (24 pages) ,
- Instructions manual (20 pages) ,
- Quick start manual (2 pages)
Subscribe to Our Youtube Channel
Related Manuals for Wurtec S3 Communicator
Summary of Contents for Wurtec S3 Communicator
- Page 1 S3 Communicator uilding owered Emergency Telephone Guide Use with Part Numbers 11-930 through 11-939 Version 5.0 September 2019...
-
Page 2: Table Of Contents
If there is any damage call us for advice at 800-837-1066 or our tech line at 419-930-1066. Before Programming the Wurtec S3 Communicator ....... 5... -
Page 3: Introduction
When programming locally be sure to have a 9V battery with adequate charge There are two ways to program the Wurtec S3C: 1) locally [using onboard keypad and battery connected to the phone or external power connected. This will energize the keypad or external power supply] or 2) remotely [accessing the S3C from another location by calling so it can be programmed. -
Page 4: Quick Set-Up (From Onboard Keypad)
/ END message again. The new recording will automatically overwrite the old recording. You can repeat this process until the message is correct. Buy Online! Wurtec.com Buy Online! Wurtec.com... -
Page 5: Resetting To Factory Defaults
The phone will then say “Reset” and then shut off. At this point anything Battery Type: Rechargeable 150 mAh or higher that has been programmed in the phone is erased and reset to factory defaults. The S3 Communicator is not polarity sensitive. Factory Defaults are as follows: Programming (Locally or Remotely) -
Page 6: Programming Ring-Down Line
VOL DN Once you have entered your choice, the phone will repeat the number back to you. If correct press to return to the previous menu or then to exit VOL DN VOL UP programming. Buy Online! Wurtec.com Buy Online! Wurtec.com... -
Page 7: Programming (Locally Or Remotely) | Advanced Options
Press to return to the previous menu to VOL DN VOL DN menu to continue programming. Press then to exit programming when continue programming. Or press then to disconnect. VOL UP VOL UP finished. Buy Online! Wurtec.com Buy Online! Wurtec.com... -
Page 8: User Preferences - Maintenance Announcements On/Off
Press to disable timing out. Press VOL DN VOL UP finished programming you can press then to exit program mode. then to exit programming mode once you are finished. VOL UP Buy Online! Wurtec.com Buy Online! Wurtec.com... -
Page 9: Touch Tone Id
VOL UP Press for first output. STEP 5 Press to program. Press to review. Press to disable. Press VOL DN return to external outputs or then to disconnect. (continued on next page) VOL UP Buy Online! Wurtec.com Buy Online! Wurtec.com... -
Page 10: Program Status
If - call cancellation on/off you are unable to get to the job site, you can call Wurtec Inc. All phone numbers - maintenance announcements are listed on troubleshooting page 21. -
Page 11: Phone Line Volume
/ END If you have any questions about the installation or operation of your S3 Communicator, please call us toll free at (800) 837-1066, 8:00 am—5:00 pm, Monday-Friday. You can also call our direct Tech Line at 419-930-1066. -
Page 12: Troubleshooting
S3 Communicator Does Not Hang Up After Conversation Ends This most commonly happens if the S3 Communicator is on a “Ring - Down” line. On most ring-down systems a “wink” signal is not sent to the phone to hang the phone up. If this is... - Page 13 Troubleshooting Flowchart Troubleshooting Flowchart Buy Online! Wurtec.com Buy Online! Wurtec.com...
-
Page 14: Glossary
Should your package arrive damaged, you must contact the shipping company to place the call is placed from the S3 Communicator. If this option is enabled the operator will NOT claim. We cannot do this for you. Do not ship the material back before the carrier inspects the... - Page 15 6200 Brent Drive, Toledo, Ohio | Ph: 800.837.1066 | Buy Online! wurtec.com...
Need help?
Do you have a question about the S3 Communicator and is the answer not in the manual?
Questions and answers