Zamel RZB-03 Manual

COMFORT MODE TIME PROGRAMMING
Open the roller blind completely.
Press PROG push-button of SRP-02 device for a longer time until LED red diode
switches on (constant signal). Next release PROG push-button. Wait (for about
5 seconds) till LED red diode switches on (first signal pulsates, next the signal is
constant).
Wait again (for about 5 seconds) till LED red diode switches on (first signal pulsates,
next the signal is constant).
Press PROG push-button of SRP-02 device, next release PROG push-button - the
roller blind moves automatically.
If the roller blind is in a required comfort position - press PROG push-button and
release it - the roller blind stops - ROLLER BLIND MOVEMENT TIME IS ADDED.
RADIO TRANSMITTERS DELETION
Press PROG push-button of SRP-02 device for a longer time.
LED red diode switches on (signal pulsates) and then it switches off.
push-button in SRP-02 - MEMORY IS DELETED.
COOPERATION AND OPERATING RANGE
Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02 180 m 200 m 200 m 200 m
RNK-04
180 m 200 m 200 m 200 m
P-256/8 230 m 250 m 250 m 250 m
P-257/4 (2) 180 m 200 m 200 m 200 m
RNM-10 230 m 250 m 250 m 250 m
RNP-01 160 m 180 m 180 m 180 m
RNP-02 160 m 180 m 180 m 180 m
RNL-01 160 m 180 m 180 m lack*
RTN-01 200 m 200 m 200 m 200 m
RCR-01 160 m 180 m 180 m lack*
RTI-01 160 m 180 m 180 m 180 m
RXM-01 230 m 250 m 250 m 250 m
* 1-channel transmitters do not cooperate with roller blind controllers
CAUTION: The given range concerns open area - an ideal condition without any
natural or artificial obstacles. If there are some obstacles between a transmitter
and a receiver, it is advisable to decrease the range according to: wood and pla-
ster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %,
metal: from 90 to 100%, glass: from 10 to 20 %, Over- and underground medium
and high electrical power lines, radio and television transmitters, GSM transmit-
ters set close to a device system have also a negative influence on the range.
After 5 seconds
Release the
200 m 250 m 180 m 250 m 250 m 180 m
200 m 250 m 180 m 250 m 250 m 180 m
250 m 300 m 200 m 300 m 300 m 230 m
200 m 250 m 180 m 250 m 250 m 180 m
250 m 300 m 200 m 300 m 300 m 230 m
180 m 200 m 160 m 200 m 200 m 160 m
180 m 200 m 160 m 200 m 200 m 160 m
lack* 200 m 160 m 200 m 200 m 160 m
200 m 250 m 200 m 250 m 250 m 200 m
lack* 200 m 160 m 200 m 200 m 160 m
180 m 200 m 160 m 200 m 200 m 160 m
250 m 300 m 200 m 300 m 300 m 230 m
WIRELESS CONTROL SET - ROLLER BLINDS CONTROL
RZB-03
TECHNICAL DATA
Input (supply) terminals:
Input rated voltage:
Battery life:
Input voltage tolerance:
Nominal frequency:
Nominal power consumption:
Transmission:
Transmission way:
Maximum number of transmitters:
250 m Maximum time of roller blind
movement:
250 m
Comfort mode time adjustment:
300 m
250 m Optical signalling:
300 m
Local control terminals:
200 m
Roller blind motor power supply
terminals:
200 m
200 m Relay contact parameters:
250 m Number of terminal clamps:
200 m
Section of connecting cables:
200 m
Ambient temperature range:
300 m
Operating position:
Casing mounting:
Casing protection degree:
Protection level:
Overvoltage category:
Pollution degree:
Surge voltage:
Dimensions:
Reference standard:
RNK-02
-
3 V (battery CR2032)
3 ÷ 5 years
-
-
0,4 W („stand-by" mode)
-
0,7 W (roller blind movement)
radio 868,32 MHz
unidirectional
Coding: addressing transmission
-
Range: up to 250 m in the open air
-
- 1 ÷ 120 sec (every 0,1 sec)
LED red diode
- LOCAL (up),
-
- 2NO 5A / 250V AC3 1250 VA
-
-
-10 ÷ +55
free
wall plugs, double-sided
installation cable box Ø60 mm
adhesive tape
IP20 (PN-EN 60529)
III
-
2
- 1 kV (PN-EN 61000-4-5)
90 x 80 x 11,5 mm
Weight: 0,038 kg
PN-ETSI EN 300 220-1 PN-EN 60669, PN-EN 60950,
PN-ETSI EN 300 220-2
SRP-02
L, N
230 V~
-
+10 ÷ -15 %
50 / 60 Hz
32
120 s
(down)
(up), (down)
6
up to 2,5 mm
2
C
o
II
II
47,5 x 47,5 x 20 mm
0,039 kg
PN-EN 61000