Related Manuals for Osram e:cue SYMPL Core S
Summary of Contents for Osram e:cue SYMPL Core S
- Page 1 Light is OSRAM Our Brand AB447060035 e:cue SYMPL Core S Setup Manual...
- Page 2 AB447060035 e:cue SYMPL Core S Setup Manual (original issue) e:cue SYMPL Core S Installationsanleitung (Originalversion) Edition/Ausgabe: 23.08.19 [EN_DE_SYMPL_Core_S_Setup_v2p0] Published by / Herausgegeben von: OSRAM GmbH Karl-Schurz-Strasse 38 33100 Paderborn, Germany ©2019 OSRAM GmbH, BU Digital All rights reserved / Alle Rechte vorbehalten...
-
Page 3: Table Of Contents
Table of Contents / Inhalt Table of Contents / Inhalt English Security instructions Symbols General security instructions General device description Delivery content Connectors and interfaces User interface: LEDs Identify button: Identification & Reset & Update General remarks Transport Unpacking Warranty regulations Maintenance and Repair Disposal Support... - Page 4 Table of Contents / Inhalt Certifications Dimensions / Abmessungen...
-
Page 5: English
English... -
Page 6: Security Instructions
Connect cables and data only when the device is powered down. The device must be supplied by a separate certified SELV Class 2 power supply. The maximum length of each connected cable is 30 m. If safety instructions are missing, please contact OSRAM to receive a new copy. -
Page 7: General Device Description
SYMPHOLIGHT. Connections between servers, Cores and Nodes are always made with e:net via Ethernet. e:cue SYMPL Core S is a stand-alone engine for e:cue SYMPHOLIGHT with SYMPL Nodes as interfaces. It executes SYMPHOLIGHT shows in small to medium-sized shows and controls all available SYMPL Nodes. As a user interface it utilizes the Action Pad of SYMPHOLIGHT with all usual web browsers. -
Page 8: Connectors And Interfaces
Yellow: This SYMPL Core S is a slave in a master/slave group. Error/Status Green: Signals system activity. Orange: System load reaches 100%. Red: A system error occurred. Restart the system by disconnecting the power supply. If the error persists, contact OSRAM Service. -
Page 9: Identify Button: Identification & Reset & Update
General device description Ethernet link Off: No network connection available. On: If constantly alight, network connection available. Flashing: Data traffic over network. Power On: Device is in operation. Identify button: Identification & Reset & Update The Identify button has four functions: to send an Identify message (A), to reset the SYMPL Core S (B), and to update the firmware of the SYMPL Core S (C). -
Page 10: General Remarks
Only transport the device in its original packaging. This protects the device from damage. Unpacking Only unpack the e:cue SYMPL Core S at its installation location. To protect the device against condensation water, unpack it and wait until all moisture remaining in the device has evaporated. Condensation can occur when the device is moved from a cold to a warm location. -
Page 11: Disposal
Support In case of technical problems or questions regarding installation and repair please contact: OSRAM GmbH Customer Service Karl-Schurz-Str. 38 33100 Paderborn, Germany +49 (5251) 54648-0 support@ecue.com... -
Page 12: Installation Conditions
160 mm (with 40 mm conduit) Installation location Indoor Mounting process The e:cue SYMPL Core S is designed to mount onto a 35 mm DIN rail (EN 60715) in a vertical position. 1. Clip the device to the rail from top. -
Page 13: Power Supply
24 V DC to the SYMPL Core S. Network configuration The configuration of the e:cue SYMPL Core S is completely done via e:cue SYMPHOLIGHT. See the SYMPHOLIGHT System Manual for details on configuration, available at www.ecue.com. -
Page 14: Default Network Properties
Network configuration successful installation of the power supply is required for changing the network configuration. You can either adjust the network settings with SYMPHOLIGHT or using the web interface of the SYMPL Core S. Via the web interface extended DMX/RDM settings are configurable. Default network properties The SYMPL Core S has as factory setting the AutoDHCP enabled. -
Page 15: Network Configuration With The Web Interface
Network configuration Click “Apply” to submit the changes. The network configuration of the SYMPL Core S is completed. Network configuration with the web interface Open a common web browser on a connected PC. Enter the SYMPL Core S's IP address into the address bar: e.g. - Page 16 Network configuration Click “Apply”. The Settings page is displayed: Define the network settings at “Device Basics” to your needs. You can also change the password for entry to the web interfaces of the SYMPL Core S here. Click “Submit” to apply the settings. The network configuration of the SYMPL Core S is completed.
-
Page 17: Firmware Update
Firmware Update Firmware Update To update the SYMPL Core S, a connection of the SYMPL Core S to SYMPHOLIGHT is required. Download the SYMPL Core S Updaterfrom the e:cue website and save it on your local drive. Double-click to execute the Updater. HowTo update SYMPL Core S with an USB memory stick You will need a USB memory stick with at least... - Page 18 Firmware Update • Keep the Identify button pressed and reconnect the power supply. • The Master/Slave LED will start to blink. • Release the button immediately. After the update, the SYMPL Core S will restart and return to normal operation. HowTo update SYMPL Core S image directly to SD card Follow these steps in order: Open file SymplCoreUpdater_*.exe.
- Page 19 Firmware Update (better triple!) check to choose the drive letter matching your SD card! Check again if the drive letter corresponds to the SD card. If so, confirm overwriting. When done, power off the SYMPL Core S. Insert the SD card and power it on.
-
Page 20: Dismounting
Dismounting Dismounting Disconnect all attached cables. Dismount the e:cue SYMPL Core S from the rail by pulling the black DIN rail handle and unhitching the SYMPL Core S. The dismounting is completed. Before dismounting, appropriate measures must be taken to protect the respective components against damage caused by electrostatic discharge (ESD protection). - Page 21 1 x e:net / Ethernet, RJ45 CAT5 shielded USB 2.0 Type A microSD card with SYMPHOLIGHT software Certifications e:cue SYMPL Core S is certified according to EN 55022, EN 55024, 62368-1 Ed. 2 Conforms to ANSI / UL Std. 60950-1 4000805...
- Page 22 Dimensions / Abmessungen All dimensions in mm / Alle Abmessungen in mm 53.5 90.5...
- Page 23 OSRAM GmbH Sales Operations Head office / Zentrale: Karl-Schurz-Str. 38 Marcel-Breuer-Strasse 6 33100 Paderborn, Germany 80807 Munich, Germany +49 5251 54648-0 Phone +49 89 6213-0 support@ecue.com Fax +49 89 6213-2020 www.ecue.com www.osram.com Light is OSRAM Our Brand...
Need help?
Do you have a question about the e:cue SYMPL Core S and is the answer not in the manual?
Questions and answers