Introduction: The Vizi Hex Wash7 is a DMX intelligent, moving head, wash fixture. The Vizi Hex Wash7 has 3 DMX channel modes; 19 channels, 21 channels, or 27 channels. The fixture has two different operating modes; auto program or DMX control. The Vizi Hex Wash7 can be used as a stand alone unit or in a Primary/Secondary configuration.
Objects have fallen, or liquid has been spilled into the appliance. The appliance has been exposed to rain or water. The appliance does not appear to operate normally or exhibits a marked change in performance. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Vizi Hex Wash7 Product Registration The Vizi Hex Wash7 carries a two year limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number.
Page 7
Please keep this manual with the unit, for future reference. Vizi Hex Wash7 Dimensions 286.88mm [11.29in] 206.53mm [8.13in] 284.4mm [11.20in] 202mm [7.95in] Ø152.41mm [6.00in] 284.4mm [11.20in] 202mm [7.95in] ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
These installations should be checked by a skilled person once a year.CA The Vizi Hex Wash7 is fully operational in three different mounting positions; hanging upside-down from a ceiling, mounted sideways on trussing, or set on a flat level surface. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.).
Page 9
Omega holders into the respective holes on the bottom of the Vizi Hex Wash7. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder. Pull the safety-cable through the holes on the bottom of the base and over the trussing system or a safe fixation spot.
Page 10
Data Cable (DMX Cable) Requirements (For DMX and Primary/Secondary Operation): The Vizi Hex Wash7 can be controlled via DMX-512 protocol. The Vizi Hex Wash7 can be either a 19, 21, or 27 channel DMX unit. The DMX address is set electronically using the controls on the panel of the unit.
(DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
Page 12
Data Compliment (- signal) Pin 2 in 3 Data True (+ signal) in 3 Pin 4 - Do Not Use Not Used Pin 5 - Do Not Use Not Used ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
A DMX controller allows you to create unique programs tailored to your individual needs. 1. The Vizi Hex Wash7 has 3 DMX channel modes; 19 Channel mode, 21 Channel mode, and 27 Channel mode. See pages 13-21 for detailed description of the DMX traits.
Blue Blue Blue Blue White = White = White = White = Amber = Amber = Amber = Amber = UV = UV = UV = UV = ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 25
Blue Blue Blue Blue White = White = White = White = Amber = Amber = Amber = Amber = UV = UV = UV = UV = ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 26
Green = Blue Blue White = White = Amber = Amber = UV = UV = DMX VALUES 225-228 Green = Blue White = Amber = UV = ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 28
User Mode A B C - These are customizable DMX modes. Select either of these modes and set the amount of DMX Channels and what each channel does. 4. Press the MODE button once to return to the “User Mode Set” menu. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 29
“8”. 3. Set the DMX value of Channel 3 to your desired starting address. This will take about 20 seconds before the unit accepts the new DMX address. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 30
4. Either “Off” or “On” will be displayed, use the LEFT or RIGHT buttons to toggle between. 5. Press ENTER to confirm your selection or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 31
4. Either “Off” or “On” will be displayed, use the LEFT or RIGHT buttons to toggle between. 5. Press ENTER to confirm your selection or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 32
4. The current stand by setting will be displayed, use the LEFT or RIGHT buttons to adjust the hibernation period between 01M-99M or “Off”. 5. Press ENTER to confirm your selection or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 33
3. Press LEFT or RIGHT until “RDM PID” is displayed, and press ENTER. 4. “XXXXXX” will be displayed. “XXXXXX” represents the units current RDM ID. 5. Press ENTER or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 34
4. Either “Off” or “On” will be displayed, use the LEFT or RIGHT buttons to toggle between. 5. Press ENTER to confirm your selection or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 35
4. Either “Off” or “On” will be displayed, use the LEFT or RIGHT buttons to toggle between. 5. Press ENTER to confirm your selection or press MODE to exit. Dim Curve ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 36
2. Press the UP or DOWN buttons until “Init.Effect” is displayed, press ENTER. 3. “XXX” will be displayed. “XXX” represents the current effect position. 4. Press ENTER or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 37
3. Either Secondry 1, Secondry 2, or Secondry 3 will be displayed. Use the LEFT or RIGHT buttons to find your desired setting and press ENTER, or the press MODE button to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 38
3. Either “Off” or “On” will be displayed, use the LEFT or RIGHT buttons to toggle between. Selecting “On” will restore the factory settings. 4. Press ENTER to confirm your selection or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 39
4. Either “Off” or “On” will be displayed, use the LEFT or RIGHT buttons to toggle between. 5. Press ENTER to confirm your selection or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 40
3. Press LEFT or RIGHT buttons, until “Clear Last” is displayed, and press ENTER. 4. Either “Off” or “On” will be displayed, use the LEFT or RIGHT buttons to toggle between. 5. Press ENTER to confirm or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 41
3. The model name will now be displayed. 4. Press MODE to exit. Software. V - This will allow you to see the software version you are currently running. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 42
3. Use the LEFT or RIGHT buttons to scroll through the various functions. 4. Press ENTER when you find the function you would like to adjust or press MODE to exit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 43
Sce. Input - The Vizi Hex Wash7 features an integrated DMX recorder. Preprogrammed scenes can be transmitted to the fixture via any DMX compliant controller. This function allows those scenes to be stored in to the fixture’s built-in memory and then...
6. For your “Secondary” units, access the main menu, and press the UP or DOWN buttons so that “Function” is highlighted, then press ENTER. 7. Press the UP or DOWN buttons until “Disp. Set” is displayed, and press ENTER. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 45
2. After you have set the WiFly address, follow the DMX instructions on page 26 to select your desired DMX Channel mode and set your DMX address. 3. Apply power to the ADJ WiFly Transceiver. The fixture must be set up first before you apply power to WiFly Transceiver.
Using a flat head screw driver unscrew the fuse holder. Remove the bad fuse and replace with a new one. Vizi Hex Wash7 Dimmer Curve Chart Ramp (Fade Time) (Fade Time) Effect Standard Stage Architectural Theatre ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Unit does not respond to sound; 1. Low frequencies (bass) should cause the unit to react to sound. Tapping on the microphone, quiet or high pitched sounds may not activate the unit. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
ADJ Products, LLC be liable for any loss or damage,direct or consequential, arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. ADJ Products, LLC - www.adj.com - Vizi Hex Wash7 Instruction Manual Page...
Page 53
ADJ Products, LLC 6122 S. Eastern Ave. Los Angeles, CA 90040 USA Tel: 323-582-2650 / Fax: 323-725-6100 Web: www.adj.com / E-mail: info@americandj.com A.D.J. Supply Europe B.V. Junostraat 2 6468 EW Kerkrade The Netherlands service@adjgroup.eu / www.adj.eu Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99...