Table of Contents
Advertisement
Quick Links
Aristospray Ltd
UK & Europe
2b Stephenstown Industrial Park
Balbriggan
County Dublin
Ireland
K32 KV26
Australia
27 Tatura Avenue
Gosford
NSW 2250
Email sales@aristospray.com
www.QTechSpray.com
www.Aristospray.com
Phone
UK 01895 276751
Ireland 01 690 3162
Australia 1300 229 757
International +353 1690 3162
Aristospray Australasia PTY Ltd
27 Tatura Ave,
Gosford
NSW 2250
Phone: 1300 229 757
QTech.
QT830 Airless Sprayer.
USER
MANUAL
Advertisement
Table of Contents
Related Manuals for QTech QT830
Summary of Contents for QTech QT830
- Page 1 QTech. Aristospray Ltd UK & Europe 2b Stephenstown Industrial Park Balbriggan QT830 Airless Sprayer. County Dublin Ireland K32 KV26 Aristospray Australasia PTY Ltd Australia 27 Tatura Ave, 27 Tatura Avenue Gosford USER NSW 2250 Gosford Phone: 1300 229 757 NSW 2250 MANUAL Email sales@aristospray.com...
- Page 2 Quick check QTech QT830 Honda Engine-Drive Airless Sprayer The information on this page is intended only as a quick guide. It is no way intended as a substitute to the information on the pages following, which the user should be fully acquainted with before using an engine drive airless sprayer.
-
Page 3: Specification
TriTech T360 airless spray gun gland nut TriTech Contractor 517 Suction airless tip & guard filter 3/8” x 15m textile braided hose assembly 1/4” x 1m textile braided whip hose Prime valve Suction hose PRODUCT CODE QT830 QTechSpray.com QTech QT830 Airless Sprayer... -
Page 4: General Safety
5 Re-engage gun safety latch and close Priming Valve. If the SPRAY TIP OR HOSE IS CLOGGED, follow Step 1 through 5 above. Expect paint splashing into the bucket while relieving pressure during Step 4. QTechSpray.com QTech QT830 Airless Sprayer... -
Page 5: Specific Safety Rules
Skin injection by high pressure paint is not a simple cut. It must be treated surgically immediately. WARNING: FIRE AND EXPLOSION HAZARD Take all precautions to avoid sources of sparks and ignition when spraying. Keep the machine at least 6 meters away from the spraying operation. QTechSpray.com QTech QT830 Airless Sprayer... - Page 6 + NEVER wipe off build up around the spray tip. ALWAYS wear a spray mask, gloves and protective eye wear while spraying. ALWAYS ensure fire extinguishing equipment is readily available and properly maintained. QTechSpray.com QTech QT830 Airless Sprayer...
- Page 7 NEVER ATTEMPT TO RECOUPLE THE HOSE. Examples of these are: It is not possible to recouple a high pressure hose . acetone, benzene, ether, gasoline, naphtha. Consult your supplier if in doubt. QTechSpray.com QTech QT830 Airless Sprayer...
-
Page 8: Operation
OPEN position). Fill the packing nut/wet cup with Turn the engine ignition switch clockwise to the ON position. about 2-3 drops of QTech Pull the recoil starter grip lightly until compression is felt, then pull briskly and QLube lubricating oil. -
Page 9: Shutting Off The Engine
LCD display. when switching between different types of paints. Turn the pump control switch ON (If the hose and gun do not need flushing, proceed to step 11, over page). and continue normally. QTechSpray.com QTech QT830 Airless Sprayer... - Page 10 9 Turn off the pump control and lock the trigger. The drain tube may now be rejoined to the suction tube in the material bucket. The unit is now primed and ready to install the tip and tip guard. QTechSpray.com QTech QT830 Airless Sprayer...
-
Page 11: Spray Gun
Remember to follow the PRESSURE RELIEF PROCEDURE before refilling material. If the paint does run out, the pump will suck in air. This air must be bled out, follow the instructions for PRIMING. QTechSpray.com QTech QT830 Airless Sprayer... -
Page 12: Spray Tip Selection
With these variables in mind, the operator will need to fine tune the pressure to suit the actual conditions of the situation. QTechSpray.com QTech QT830 Airless Sprayer... - Page 13 3 Watch the drain tube and as soon as the storage solution appears in the tube, bucket to the waste bucket next to it. shut the machine off and close the priming valve. This will trap the storage solution inside the pump to protect it. QTechSpray.com QTech QT830 Airless Sprayer...
-
Page 14: Weekly Maintenance
2 The engine oil should be changed after the first 20 hours of operation (break-in period). Thereafter, it should be changed every 100 hours. NOTE: All engine repairs should be entrusted to an authorised service centre. QTechSpray.com QTech QT830 Airless Sprayer... - Page 15 OFF and then back ON again to reset Maximum Clutch will When No further pressure disengage pressure signal action required exceeded is normal, will automatically return to QTechSpray.com QTech QT830 Airless Sprayer...
- Page 16 QTech QT830 QTechSpray.com QTech QT830 Airless Sprayer...
- Page 17 SOCKET CAP SCREW (M5x8xP0.8) NEEDLE BEARING (TA2830) COVER PLATE SPINDLE SOCKET CAP SCREW (M8x35xP1.25) PARALLEL KEY (6x6x20) ENGINE NEEDLE BEARING (TA4540) FITTING (PT1/4" x 9/16"-18) FLAT HEAD MACHINE SCREW (M5x12xP0.8) MOUNTING TENON (10x10x100) PRESSURE TRANSDUCER (110V&220V) QTechSpray.com QTech QT830 Airless Sprayer...
- Page 18 PANHEAD TAPPING SCREW (M4x8) SOCKET CAP SCREW (M8x16xP1.25) HEX BOLT (M8x35xP1.25 NYLOCK NUT (M8xP1.25) PUSH BUTTON SWITCH CABLE GLAND (SB5F-3) CABLE GLAND (SB5M-1) GROMMET SOCKET CAP SCREW (M4x6xP0.7) SOCKET CAP SCREW (M5x12xP0.8) MOUNTING BRACKET TOOL BOX QTechSpray.com QTech QT830 Airless Sprayer...
Need help?
Do you have a question about the QT830 and is the answer not in the manual?
Questions and answers