Entering Manufacturer Codes - Yamaha RX-V795RDS Owner's Manual

Entering manufacturer codes

If you have a component which is not a Yamaha model, you can enter the code for the manufacturer of the component in the
corresponding position of the selector dial. By doing so, you can control the component with the remote controller.
Refer to the code list at the end of this manual for the code numbers you need.
Notes
Some Yamaha CD players and tape decks cannot be controlled with the default codes. To control such a model, enter the code
for the model in the corresponding position.
If there is no code applicable for your component in the code list, you must use the remote controller provided for the component.
Entering a code
1
Set the selector dial to the position for controlling the
component. (For example, set to "VCR" for a VCR.)
POWER
/DTS
SURROUND
CD
2
Press both of the VOLUME
same time and hold them until the indicator flashes
twice.
TV
CODE SET
MUTE
VOLUME
3
Use the numeric keys to enter the four-digit
manufacturer code for the component to be used.
Make sure that the indicator flashes twice.
/DTS MOVIE
SURROUND THEATER 2
MOVIE
CD TAPE/MD
THEATER 1
TUNER
1 3
2
MONO MOVIE DISCO
DVD/LD VCR
TV SPORTS
TV/DBS
4 6
5
ROCK
CHURCH
PHONO
JAZZ CLUB
V-AUX
7 9
8
HALL TEST
+
EXT. DEC. 100
+
10
0
CLEAR
ENTER
A/B/C/D/E
* If the indicator does not flash, repeat step 3 and enter
the code again.
4
Try operating the component with the remote controller
to check the code entering is successful.
Note
If the component cannot be controlled, enter another code for
the same manufacturer.
STANDBY
C
MOVIE
THEATER 2
MOVIE
TAPE/MD
THEATER 1
and keys at the
POWER STANDBY
C
Flashes
twice.
POWER
STANDBY
C
Flashes
twice.
Entering a code for a second (or third) VCR
You can use the CBL/DBS or DVD MENU position, or both of
them to control a second (and/or third) VCR if you do not use a
cable TV, DBS tuner, DVD player etc.
* If you will use the DVD MENU position for a second (or third)
VCR, you must enter the code for an LD player in the DVD/LD
position.
1
Set the selector dial to the CBL/DBS or DVD MENU
position.
2
Press both of the VOLUME
same time and hold them until the indicator flashes
twice.
TV
CODE SET
MUTE
VOLUME
3
Press the MUTE key.
4
Use the numeric keys to enter the four-digit
manufacturer code for the second (or third) VCR. Make
sure that the indicator flashes twice.
/DTS MOVIE
SURROUND THEATER 2
MOVIE
CD TAPE/MD
THEATER 1
TUNER
1 3
2
MONO MOVIE DISCO
DVD/LD VCR
TV SPORTS
TV/DBS
4 6
5
ROCK
CHURCH
PHONO
JAZZ CLUB
V-AUX
7 9
8
HALL TEST
+
100
EXT. DEC.
+
10
0 CLEAR
ENTER
A/B/C/D/E
* If the indicator does not flash, repeat step 4 and enter the
code again.
5
Try operating the component with the remote controller
to check the code entering is successful.
Note
If the component cannot be controlled, enter another code for
the same manufacturer.
REMOTE CONTROLLER
POWER STANDBY
M
/DTS MOVIE
SURROUND THEATER 2
MOVIE
CD TAPE/MD
THEATER 1
and keys at the
POWER
STANDBY
M
Flashes
twice.
TV
CODE SET
MUTE
VOLUME
POWER STANDBY
M
Flashes
twice.
71