Yamaha RX-V795RDS Owner's Manual page 43

Automatic preset tuning
You can make use of an automatic preset tuning function for RDS stations. With this function, this unit performs automatic tuning
and stores RDS stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 40.
To store stations
1
FM/AM
2
Press and hold for more than 3 seconds
MEMORY
MAN'L/AUTO FM
MEMORY
Flashes.
3
DOWN TUNING
To tune to higher frequencies, press the "UP" side once.
To tune to lower frequencies, press the "DOWN" side once.
* If the TUNING button is not pressed, in a while, the
automatic preset tuning begins automatically toward higher
frequencies.
The automatic preset tuning begins from the frequency
currently displayed. Received stations are programmed to
A1, A2 ... A8 sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other groups
(B, C, D and E) in that order.
NATURAL SOUND AV RECEIVER RX V795RDS
STANDBY/ON
A/B/C/D/E 1 2 3 4 5 6 7
BASS TREBLE
BASS TONE
PHONES SPEAKERS 0 0
EXTENSION BYPASS
l l l l
A B
2 2 2 2
3 3 3 3
ON OFF ON OFF 4 4 4 4
5 5 5 5
DVD/LD
CD
TV/DBS TUNER
V-AUX PHONO
STEREO VCR
AUTO 0 20 100
UP
CINEMA DSP
VOLUME
INPUT SELECTOR
l6
20 l2
28
40
TAPE/MD MON
/EXT. DECODER
60
0
–dB
TUNING
8 MEMORY EDIT FM/AM DOWN TUNING UP INPUT MODE
MODE
MAN'L/AUTO FM AUTO/MAN'L MONO
BALANCE RDS MODE SET VIDEO AUX
/ FREQ EON LEVEL MENU EFFECT
0
l l
2 2
3 3 PTY SEEK PROGRAM
4 4
L 5 5 R
MODE START S VIDEO VIDEO L AUDIO R
2 1 3
If you want to store the first received station to the
desired preset station number.
If, for example, you want to store the first received station to
C5, select "C5" by using the A/B/C/D/E button and the preset
station number selector buttons after pressing the MEMORY
button in step 2. Then press the TUNING button. The first
received station is stored to C5, and next stations to C6, C7 ...
sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section "To recall a preset
station" on page 40.
To recall a preset station
Simply follow the procedure of the section "To recall a preset
station" on page 40.
A recalled station is shown by the frequency (and the station
name if the station employs PS data service) on the display.
Notes
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section "To store stations" on page 40.
The automatic preset tuning search will be performed
through all RDS network frequencies until stations are
stored up to E8. If the number of received stations is not
enough to be stored up to E8, the search is finished
automatically after searching all frequencies.
With this function, only RDS stations with sufficient signal
strength are stored automatically. If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section "To store stations" on page 40.
* There may be a case that this function cannot receive a
station which could be received by the automatic tuning
method. This is because this function receives a large
volume of PI (Program Identification) data along with the
station.
BASIC OPERATION
8
4
2
41