Page 5
Screw fuel can cap on tightly and shake the mixture before fueling your machine. Your Atom Edger is powered by a two-stroke, air cooled engine which requires a fuel mixture of gasoline and two-cycle oil that is used for air-cooled Before fueling the edger, clean the filer cap and engines.
Need pre-measured engine oil? Contact your local authorized Atom dealer. Remember. .. • Always mix two-cycle oil with gasoline before fueling your edger. Never, ever run your Edger on gasoline alone.
10. Throttle trigger (engine accelerator control) is operated by pushing down interlock with thumb and pulling on trigger (Fig. 11 ). EDGING INSTRUCTIONS The Atom Edger is very easy and simple to use. With both arms fully extended some downwards, as in Fig. 16, hold...
Page 8
(Fig 22). you are familiar with 12. Clutch: The Atom Edger is equipped with a the controls and the centrifugal clutch. DO NOT run edger at low handling of the Atom speeds (or, if blade is jammed, at high engine Edger.
IIIIAINTENANCE INSTRUCTIONS (CONTINUED) CHECKING THE SPARK PLUG Clean plastic dust cap and housing; press back by gently tapping into place. Clean inside blade cover If engine is low on power, difficult to start or runs of any built up dirt. poorly at idling speed, check the spark plug.
MAINTENANCE INSTRUCTIONS (CONTINUED) • The loss of engine power that is not corrected by 2. If filter torn or very dirty cleaning the air filter and muffler. replace. • The engine operates in an erratic or fuel-rich 3. Wash filter condition Ondicated by excessive exhaust smoke detergent and water (Rg.
Replace exhaust spark arrestor if worn, broken or to overheat, and that blocked (Fig 36}. in turn may cause mechanical failure on Cylinder fin the part of the Atom � Edger. Remove air .._ ... deflector to clean. Muffler FIG 37...
Page 14
� S4 II/ATOM' MODEL 505 LAWN EDGER PARTS LIST �...
Page 15
II/A TOM G 34L , ,e --0 � 47 ENGINE PARTS � � 4 9 IDENTIRCATION ( •...
Page 16
II/ATOii/i G34L ENGINE PARTS LIST KEY# PART# DESCRIPTION KEY# PART# DESCRIPTION 46600 c-vlinder 46659 Knob 46601 Bolt, MSx L20 46660 Plate, Stoooer 46602 Gasket, Base Pulley � 46603 Crankcase Comp. Screw, MS x L14 46604 46663 Collar 46605 Gasket, Case 46664 Insulator 46606...
ENGINE TROUBLESHOOTING (CONTINUED) THE ENGINE RUNS POORLY _, t ---l , ___ H ______ �r---• -.. I .. __ ___ E_ C 1'_ u _s e _s _ ___ LE M _ _ I ON . .., TION PROS __ ,._F_I ND _____ __ .., _ NG...
COMPLETE WORKSHOP MANUAL • NOTE • TO REPAIR THROTTLE TRIGGER ASSEMBLY 1. Remove scre ws shown in Fig 38 and remove cover and a l l parts. Re assemble FIG45 f o l l ows. 2. Fit thrott l e inter-l o ck c omp r e s-s i on spring (F i g 45 ).
COMPLETE WORKSHOP MANUAL (CONTINUED) 3. Carefully push new blade shaft #43114 up into bearing and tap through carefully so washers, crown gear and spacer remain in position and the 3/8 FIG53 bolt is pushed out (Fig. 50 ) . 4. When blade shaft FIG50 comes through, turn assembly over.
Page 22
COMPLETE WORKSHOP MANUAL (CONTINUED) 4. With a soft hammer, tap casing down until it TO REPAIR CLUTCH bottoms on pinion bearing (Fig. 66). Replace these parts if the Outch spring is broken, the 5. Flt bearing location screw (See Fig. 59 marked A) Clutch fibre is worn or the Clutd1 bolt or shoe holes are and leave nut loose.
Page 23
TIE N30VE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. to ooy damage to the Atom Edger that Is the resut of improper maintenance or to any Atom Edger that has been altered o, moclfied so as to adversel affecl the product's This warranty �...
Need help?
Do you have a question about the 205AV and is the answer not in the manual?
Questions and answers