Yamaha PortaTone PSR-550 Owner's Manual page 142

MIDI Data Format
(3-6-1-2) TEMPO CONTROL
binary hexadecimal
11110000 F0
01000011 43
01111110 7E
00000000 01
0ttttttt TT
0ttttttt TT
0ttttttt TT
0ttttttt TT
11110111 F7
The internal clock will be set to the received Tempo value.
Tempo Meta Event is a large data block (24-bit), it is divided into 4 groups with 7-bits
going into each of the Tempos 1-4 (4 receives the remaining 3 bits).
(3-6-2) UNIVERSAL SYSTEM EXCLUSIVE
(3-6-2-1) UNIVERSAL REALTIME MESSAGE
(3-6-2-1-1) MIDI MASTER VOLUME (Receive only)
binary hexadecimal
11110000 F0
01111111 7F
01111111 7F
00000100 04
00000001 01
0sssssss SS
0ttttttt TT
11110111 F7
or
11110000 F0
01111111 7F
0xxxnnnn XN
00000100 04
00000001 01
0sssssss SS
0ttttttt TT
11110111 F7
The volume for all channels will be changed simultaneously.
The TT value is used as the MIDI Master Volume value. (the ss value is ignored.)
(3-6-2-2) UNIVERSAL NON REALTIME MESSAGE
(3-6-2-2-1) GENERAL MIDI SYSTEM ON
binary hexadecimal
11110000 F0
01111110 7E
01111111 7F
00001001 09
00000001 01
11110111 F7
or
11110000 F0
01111110 7E
0xxxnnnn XN
00001001 09
00000001 01
11110111 F7
Depending upon the received ON message, the System Mode will be changed to XG.
Except MIDI Master Tuning, all control data be reset to default values.
This message requires approximately 50ms to execute, so sufficient time should be
allowed before the next message is sent.
The bank select message for the channel 10 and the NRPN message are not received in
the GM mode.
(3-6-3) XG STANDARD
(3-6-3-1) XG PARAMETER CHANGE
(3-6-3-1-1) XG SYSTEM ON
binary hexadecimal
11110000 F0
01000011 43
0001nnnn 1N
01001100 4C
00000000 00
00000000 00
01111110 7E
00000000 00
11110111 F7
Depending upon the received ON message, the SYSTEM MODE will be changed to
XG.Controllers will be reset, all values of Multi Part and Effect, and All System values
denoted by "XG" data within All System will be reset to default values in the table.
This message requires approximately 50ms to execute, so sufficient time should be
allowed before the next message is sent.
142
Exclusive status
YAMAHA ID
Style
Tempo4
Tempo3
Tempo2
Tempo1
End of Exclusive
Exclusive status
Universal Realtime
ID of target Device
Sub-ID #1=Device Control Message
Sub-ID #2=Master Volume
Volume LSB
Volume MSB
End of Exclusive
Exclusive status
Universal Realtime
When N is received N=0-F, whichever is received.
When N is transmitted N always=0.
X = don't care
Sub-ID #1=Device Control Message
Sub-ID #2=Master Volume
Volume LSB
Volume MSB
End of Exclusive
Exclusive status
Universal Non-Realtime
ID of target Device
Sub-ID #1=General MIDI Message
Sub-ID #2=General MIDI On
End of Exclusive
Exclusive status
Universal Non-Realtime
When N is received N=0-F, whichever is received.
When N is transmitted N always=0.
X = don't care
Sub-ID #1=General MIDI Message
Sub-ID #2=General MIDI On
End of Exclusive
Exclusive status
YAMAHA ID
Device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
(3-6-3-1-2) XG PARMETER CHANGE
binary hexadecimal
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1N Device Number
01001100 4C Model ID
0aaaaaaa AA Address High
0aaaaaaa AA Address Mid
0aaaaaaa AA Address Low
0ddddddd DD Data
| |
11110111 F7 End of Exclusive
For parameters with data size of 2 or 4, transmit the appropriate number of data bytes.
For more information on Address and Parameters, refer to < Table 1-2 > - < Table 1-5 >.
The data types listed below are transmitted and received.
System Data
Multi Effect1 Data
Multi Part Data
Drums Setup Data
(3-6-3-2) XG BULK DUMP
binary hexadecimal
01110000 F0 Exclusive status
01000011 43 YAMAHA ID
0000nnnn 0N Device Number
01001100 4C Model ID
0bbbbbbb BB ByteCount MSB
0bbbbbbb BB ByteCount LSB
0aaaaaaa AA Address High
0aaaaaaa AA Address Mid
0aaaaaaa AA Address Low
0ddddddd DD Data
| |
0ccccccc CC Check sum
11110111 F7 End of Exclusive
For more information on Address and Byte Count, refer to < Table 1-2 > - < Table 1-5 >.
The Check Sum value is set such that the sum of Byte Count, Address, Data, and Check
Sum has value zero in its seven least significant bits.
If the top of the block is appointed to the Address the XG Bulk Dump, Bulk Request
will be received.
The Block is a unit that consists of the data, arranged in the list, as the Total Size.
The data types listed below are transmitted and received.(These are transmitted only
after a Bulk Dump request is received.)
System Data
System Information (Transmit ONLY)
Multi Effect1 Data
Multi Part Data
Drums Setup Data
(3-6-3-3) XG PARAMETER REQUEST (Receive only)
binary hexadecimal
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0011nnnn 3n Device Number
01001100 4C Model ID
0aaaaaaa AA Address High
0aaaaaaa AA Address Mid
0aaaaaaa AA Address Low
11110111 F7 End of Exclusive
For more information on Address and Byte Count refer to < Table 1-2 > - < Table1-5 >.
The data types listed below are received.
System Data
Multi Effect1 Data
Multi Part Data
Drums Setup Data
(3-6-3-4) XG DUMP REQUEST (Receive only)
binary hexadecimal
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0010nnnn 2n Device Number
01001100 4C Model ID
00aaaaaaa AA Address High
00aaaaaaa AA Address Mid
00aaaaaaa AA Address Low
11110111 F7 End of Exclusive
For more information on Address and Byte Count refer to < Table 1-2 > - < Table1-5 >.
The data types listed below are received.
System Data
System Information
Multi Effect1 Data
Multi Part Data
Drums Setup Data